In most cases, you’ll find wall studs on the wall above your fireplace. Use a high-quality stud finder to search for the studs before you secure the mount. Using wall studs will result in a more secure mount.
Can you use plywood for studs above a fireplace?
Other Stud Finding Tips. It’s becoming common practice to use plywood backing above fireplaces. This is done to make TV mounting easy because you can anchor anywhere into the plywood using a hollow wall toggle. Keep this in mind if you have trouble finding studs above a fireplace.
How to find studs between wall plates?
In the case of wall plates, simply remove the wall plate, and then get a thin tool to stick between the wall and fixture. The tool will either go into the empty space behind the drywall, or stop, indicating that you've found a stud. 4. Drill Pilot Holes Even after utilizing the first three methods, you still might not where the studs are.
How far apart should studs be on a wall?
Most homes are built with 16” on-center studs, which means there should be a stud every 16”. If you have trouble finding studs on a wall, verify how far apart they are in the home by locating and measuring them on another wall.
Can you use a stud finder on a wall?
Sometimes, electronic and magnetic stud finders won’t do you much good. This is often the case when it comes to old homes with lathe and plaster walls. In these cases, you can rely on wall fixtures, such as electrical outlets, light switches, cable jacks, and sconces, to locate studs.
How far apart are studs above a fireplace?
They're always spaced either 16 or 24 inches on center (measured from center to center) along the wall and run between the floor and ceiling. Drywall or lath (for plaster walls) attaches to the edge of the studs.
Can you drill above a fireplace?
Here are a few tools you'll likely need to mount a tv above a fireplace: Anchors, a hammer drill, a high-impact drill and bits, and a dry shop vacuum.
Can I mount a TV above my fireplace?
The short answer is – yes. However, to ensure your television isn't damaged from the heat, care must be taken to ensure heat generated by the fireplace is redirected away from television. There are several ways to do this, such as installing a proper mantel and building an alcove for the television.
How do I find a stud in my fireplace?
If you cannot locate a stud, try tapping a small nail into the wall board near an existing fixture. If it meets resistance behind the wall-board then you have a stud. Wall studs should be spaced in regular intervals (usually 16" on center in the US) so you can simply measure over to your mount area to locate them.
How do you hang a TV over a fireplace without studs?
How to Mount a TV Above a Fireplace Without Studs?Choose a TV Wall Mount. As we mentioned before, select a wall mount that is compatible with the weight and size of your room. ... Drill Pilot Holes. Use an electric drill for this. ... Secure the TV Mount with Toggle Bolts. ... Attach the Mounting Plate to the TV. ... Hang the TV.
Can you mount a TV above a brick fireplace?
Mounting a TV always requires special equipment, no matter what type of wall you use. Mounting a TV above a brick fireplace requires masonry bits and a hammer drill to get the job done.
How high should a 65 inch TV be mounted above a fireplace?
In general, the answer is 60-68 inches above the ground; however, this number will vary depending on the height of the homeowner. If you have to lift or strain your neck at all, it's too high.
How far above a fireplace should a TV be mounted?
The Rule of Thumb. The general rule of thumb is that if your fireplace mantle is less than four feet tall, the product should ideally be 12 inches above it. In the case it is more than four feet tall, your TV should ideally be 6 inches above it or the same height.
How much weight can a mantle hold?
The maximum weight for all 60INCH MANTELS is 150 lbs. The maximum load for all 72 inch mantels is 180 lbs.
Where do you put your electronics when TV is above fireplace?
The rule in place is to keep the wall-mounted television about 3 to 7 inches above the fireplace. It gives you a good viewing angle. It also helps you easily conceal the HDMI cables using a wire raceway.
What might be behind the wall above my fireplace?
If you live in a newer home the walls above the fireplace are likely to be drywall over standard wood studs or furring strips. Studs are usually made of 2x4's while furring strips are only an inch wide.
Can you put a TV on a chimney wall?
It's not advisable to mount a TV above a fireplace because excess heat and electronics don't mix. The area above the fireplace is often warmer than other wall surfaces in your home. Consider this: A gas fireplace can generate 20,000 to 35,000 British thermal units (BTUs) of heat per hour.
Is it safe to drill into a chimney?
don't drill into the chimney masonry without knowing if you are drilling into a joint. If you drill and drive a fastner into a joint you can crack the joint, causing a gap all the way to the inside of the chimney. Hot flue gasses can then escape.
How do you hang a TV over a fireplace?
0:592:03How to Mount a TV Above a Fireplace - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's very easy just to drag along your wall. When identifies that stud location. You just mark withMoreIt's very easy just to drag along your wall. When identifies that stud location. You just mark with a pencil the third. Step is then determining the location to mount the wall plate to the wall.
Can you drill into chimney breast?
You need a more powerful drill and decent quality drill bit what your describing wouldn't stop a decent drill and drill bit drilling it sounds you lack the power as chimneys don't have boarding on the inside even so if let's say a brick was lose or anything that still wouldn't stop the drill unless it lacked power.
Can you drill through fire brick?
0:064:23How to drill firebrick - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's pretty simple to do firebrick is pretty for it feels a get a little break but what I do anywayMoreIt's pretty simple to do firebrick is pretty for it feels a get a little break but what I do anyway I take a regular power drill non hammer. Action not a hammer drill.
How to find studs in a wall?
The easiest and most common method of locating studs within a wall is to use an electronic stud finder. Each model varies slightly , but generally speaking, you place the stud finder on the wall, hold down a power button until the device beeps – this indicates that it has finished taking an initial reading of the well – then slowly move the stud finder along the wall until it lights up/beeps indicating a stud.
How to tell where a stud is?
You simply move the stud finder back and forth on a wall until you cross over a drywall screw. The magnet in the stud finder will snap to the drywall screw, and now you know where a stud is. The downside to this method is that it won’t tell you where the center of the stud is, just the location of the drywall screw.
How to use a stud finder?
When using a stud finder, use painters’ tape to mark out at least three studs in a row, then measure the distances between the studs. If the studs are equidistant apart, you can be sure the stud finder actually marked studs, as opposed to some other object in the wall.
What is wrong with electronic stud finders?
The problem with electronic stud finders is that they can mistake other objects in the wall as studs, such as water pipes and electrical wires. Sometimes drywall seams are also mistakenly marked as studs.
What is a flute?
Flutes are those things you put up to your lips – and you blow on them.
Can a magnetic stud finder scratch drywall?
If an electronic stud finder marks a stud, but you can't locate any drywall screws in that area, there likely isn't a stud there. Some cheap magnetic stud finders can scratch the wall, so make sure you get one with felt pads to protect the wall. 3. Reference Wall Fixtures.
Can you find studs above a fireplace?
Even after utilizing the first three methods, you still might not where the studs are. This is a common scenario when trying to find studs above a fireplace, where there may not know actually be any studs to find. At this point, you need to drill into the wall.
