Full Answer
What is a coax plug on a TV aerial?
Although most TV aerial splitters/ amplifiers now utilise F connectors the connection on your TV and most wall plates/ sockets is the ‘coax plug’ or it’s more accurate name is the Coax IEC plug. This video shows you how to install a coax plug.
What type of socket is used for TV aerial?
Coax IEC Sockets The most common TV aerial socket type that most people will be familiar with is the Coax IEC socket. This type of outlet is most common for TV aerial connections, but is also commonly used for FM radio.
What do the connectors do on an aerial?
We explain what the connectors do, and aim to point you in the right direction. An Aerial Flylead is used to connect from a TV aerial socket on the wall to an aerial input socket on a TV or set-top box. They are also used to connect set-top boxes and recorders to TV sets. These will have a male aerial plug at each end.
What is the difference between male and female coaxial cables?
Again, this is the coax plug that most people are familiar with. The opposite of the female socket is the male socket for obvious reasons. If you have a male socket you will need either a cable with a female plug fitted to it or a male plug with a coaxial coupler fitted into it. This will provide you with a female connection.
Do coax cables have male and female ends?
Since coax cable has 2 strings of wire (the shield and the core), gender is determined by the middle (core) wire. If you look at a connector and it has a pin in the middle, it's a male. If the connector has a hole in the middle, it's a female.
What is a male aerial connector?
An Aerial Flylead is used to connect from a TV aerial socket on the wall to an aerial input socket on a TV or set-top box. They are also used to connect set-top boxes and recorders to TV sets. These will have a male aerial plug at each end.
Why do I have two aerial sockets?
The most common reason that a satellite TV receiver will have two LNB connections is because it is a twin tuner model, commonly known as a PVR which is an abbreviation of Personal Video Recorder which usually has an in-built HDD for storing recorded TV directly onto the unit itself so you can watch back at a later date ...
What connectors are on a TV aerial cable?
Guide To Coax Cable Plugs & ConnectorsScrew On F Connectors. ... Crimp on F Plugs. ... Compression F Plugs. ... Quick F Connector – Push On. ... 0.65mm F Plugs. ... 1.65mm F Plugs. ... F Couplers. ... Male IEC Plug.More items...•
How do you fit a male aerial connector?
1:153:47Tv coax aerial plug fitting Tutorial Guide - How to - YouTubeYouTubeStart of suggested clipEnd of suggested clipContact there. So I should get good signal. So last part of the coax plug. And the screw part theMoreContact there. So I should get good signal. So last part of the coax plug. And the screw part the back together like that it's hanging up the crimper make it nice and secure on the cable.
Are all TV aerial cables the same?
There are two main types of coaxial cables – ones with an impedance of 75 Ohm (Ω) and ones with an impedance of 50 Ohm. Cables with 75 Ohm are mostly used for video signals, while 50 Ohm cables tend to be used for data and wireless communications.
Do aerial sockets have power?
More precisely, the signal captured by the aerial is actually alternating current electricity. But its frequency is much higher than of your home's electrical supply. However, this won't make cutting a coaxial cable an impossible task.
Does splitting an aerial weaken the signal?
Aerial splitters will weaken your signal. However in reasonable signal strength areas your TV can cope with this loss OK, particularly if only splitting the signal twice. Thus, unless you live in a known poor signal area, we recommend trying a splitter before you try an amplifier / booster.
Can you run 2 TVs off 1 aerial?
The good news is you can run numerous TVs off of one aerial and not need dozens. The not-so-bad news is you will need to order a TV aerial splitter. In theory, the signals your aerial receives can be amplified and split for different TVs–and they can be split up for as much as you need.
How do you put a male end on a coaxial cable?
2:044:00How to Wire A Coaxial Cable (Male Coaxial Plug) - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart off by putting the shoulder on to your coax cable. Make sure you do this you wouldn't believeMoreStart off by putting the shoulder on to your coax cable. Make sure you do this you wouldn't believe how many times I forgot open up the collar. And put it over the end of the cable.
How does a TV aerial socket work?
A screened socket means that the cable termination is with a metal housing. The metal housing that the coax cable termination is inside helps stop RF leakage and signal loss, as well as protecting against impulse noise and EMI/ RF interference which can cause the TV picture to pixelate.
What do I need to connect TV to aerial?
You'll also need an aerial lead and a working aerial.Plug your aerial lead into the aerial socket on your box (1). ... Using an HDMI cable, connect to the equivalent socket on your TV to the port marked HDMI 1 on the box. ... Put your TV on standby, then switch the TV on using your TV remote control.More items...
What does a male connector look like?
A male connector is commonly referred to as a plug and has a solid pin for a center conductor. A female connector is commonly referred to as a jack and has a center conductor with a hole in it to accept the male pin.
What is an aerial connector called?
Coaxial cable, also known as TV aerial cable or coax, is primarily used to carry video and data signals from an aerial to a device such as a satellite dishes or television. This is due to the well insulated conductor wire which prevents frequency interference.
What are male and female connectors used for?
For electronics components, gender is used to distinguish "mating connectors." Mating interconnects match together in size, configuration and number of pins. In case you didn't know, a "male" connector usually has a pin or pins "sticking out" and the "female" connector is designed to receive those pins.
What do I need to connect TV to aerial?
You'll also need an aerial lead and a working aerial.Plug your aerial lead into the aerial socket on your box (1). ... Using an HDMI cable, connect to the equivalent socket on your TV to the port marked HDMI 1 on the box. ... Put your TV on standby, then switch the TV on using your TV remote control.More items...
What is the weather proof connector for satellite dish?
There are a range of weatherproof F compression connectors that are perfect for outside terminations like at the satellite dish LNB. These have an internal rubber O ring that acts as seal. The plugs I recommend for this purpose are the Cablecon Compression F connectors which are rated to IPX8, which means that the plug can be submerged in water deeper than 1 metre. Personally when I used this, which I only typically do on communal satellite dish installations I would also smear some silicone grease on the outside of the plug to keep this part of the plug free from corrosion and/or use self-amalgamating tape on any outside F joins.
Why do I use crimp on plugs?
I always use crimp on plugs for commercial and communal MATV, SMATV and IRS installations as they comply with regulations and offer superior performance. It all adds up in communal systems due typically the very large number or plugs and connections that the signals have to pass through before they reach the TV points. Crimp on plugs can be tricky to install, there are special tools that are available to help you insert the plug into the coax cable and as already said you will need a crimping tool to actually crimp the plug. Sometimes this can be quite a squeeze but over time it really helps build those hand muscles up.
What is an F plug?
The F plug came from the USA and is most commonly used for satellite dish connections at both the satellite LNB and the satellite receiver itself. The F plug has a threaded connection that allows the plug to be screwed in securely and not fall out of position which can be common with over types of coax plugs. F plugs are also now very common for TV aerial and communal TV systems for connections at aerials, splitters, amplifiers and for joining coax cable.
What is a right angle coax plug?
Right angle coax plugs are very handy to for making connections in tight spaces where the bend radius on the cable will not fit or the cable will become squashed. This is very common for wall mounted TV's where some models have the aerial connection leaving the back of the TV at right angle to the wall. A right angled connection will allow to plug to fit inside a much tighter space and allow a TV to be installed as close to the wall as possible. The most common of the two is the IEC right angled connection but a F right angled connector is also relatively common.
What is an F coupler?
An F coupler is a plug that will join two cables together using F type terminations. The most common type of F coupler by far is the F barrel connector which is a female to female plug that will allow two F plugs on two pieces of coax to create an F join. There is another type of F coupler which is far less common that has male-male connections either side which can be used with two female F connections.
What is a female IEC plug?
A female IEC plug is the opposite of the male plug. The female IEC connection is most commonly used on signal/ RF outputs of AV equipment and return feeds from Sky boxes etc. Most STB’s or PVR’s that have an aerial input will also have an aerial output or loop that allows the signal to go onto feed another piece of equipment, usually the TV itself. The splitting of the signal is incorporated into the AV equipment so there is no need for any additional signal splitting equipment. By providing both male and female connections on the equipment you can easily see which one is the output and which one is the input. This is why many TV flylead/ RF Leads that are purchased have a male connector one end and a female connector the other. A female coax connection can also be achieved with a male plug with a coax coupler attached.
Why do I need compression plugs for TV?
The most common reason that I use compression plugs is for the larger type coax cables that are only commonly used on communal TV systems to help reduce signal losses over long distances.
What to do if your aerial connector is damaged?
Got a damaged aerial connector? Replace the male connector plug with a co-ax plug. Basic co-ax plug at Maplin– see also all aerial connectors at Maplin.
What is HDMI connector?
HDMI connector. Typically used to connect a High Definition set-top box or DVD player to an HD-Ready TV set. We have a page dedicated to HDMI cables, connectors and converters. See our HDMI advice page.
What is an aerial flylead?
An Aerial Flylead is used to connect from a TV aerial socket on the wall to an aerial input socket on a TV or set-top box. They are also used to connect set-top boxes and recorders to TV sets. These will have a male aerial plug at each end. TV Aerial Flylead at Maplin.
What is a wall plug?
the wall plug is a F connector. How do one connect to a HDMI port?
What color connectors are used for a TV?
Can be used to connect some types of set-top box to a TV set. Red, Green and Blue for Y,Pb,Prcomponent connectivity. Note that these carry video only, not audio. For Component connectors and adapters, go to a maplin.co.ukor tvcables.co.uk.
Is HDMI cable compatible with SCART?
SCART and HDMI are not compatible and there’s no adapter – you need to add HDMI cable(s)
Where is the co-ax plug on a TV?
A co-ax plug is the kind you’d expect to find on the end of the wire that comes from your TV aerial.
What is an antenna plug?
Antenna plugs and sockets are devices that connect the TV set to the TV antenna (aerial).
What is the phone number for Selby antenna?
Feel free to call and speak with our Selby Techs on 1800 69 2225 if you would like further information about antennas.
What is an outdoor antenna?
A television antenna is designed to receive over-the-air broadcast television signals. The most popular and effective antenna is the “outdoor antenna” which is typically mounted on top of the roof using a long pole. A cable, often referred to as "RG6, Quad Shield or Coax” is connected to the antenna, and is usually fed through the roof, down the wall cavity and terminated at a wall plate. A "fly-lead" will then be connected from the wall plate to the back of your television or set top box.
Can you install an antenna on a roof?
Installing an antenna is not always straight forward, so if you’re not certain that you like the idea of getting up on your roof consider using a qualified installer to do it for you.
