In most cases, a 10-Inch miter saw allows you to cut up to 6 inches. Nevertheless, you will find some changes in this; therefore, it would be better to check your particular saw. If you notice your saw blade, you’ll find that it is wider in the middle than it is in the top or the bottom.
Full Answer
What size Miter Saw do I need to cut a 4×4?
We should cut the 4×4 with 10″ inch miter saw occasionally. If you have a 10″ inch miter saw, we recommend you not to cut any piece which is bigger than 4×4.
What is a 10 inch miter saw good for?
The 10-inch blade can do angle crosscuts that are up to 5 inches wide, generally seldom more than 4 inches. For beginners miter saw, a 10″ miter saw is your best bet. We can cut through the material more quickly and have smoother edges.
How do you cut a 4x4 with a 10-inch saw?
One way to chop a 4x4 in a single pass is by adjusting the blade guard to essentially increase the saws cutting capacity. If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4x4 post, even when utilizing a 10-inch blade.
Can a miter saw cut a fence?
Miter saws can cut through wood, plastic, and some metals depending on the kind of blade that we are using. Remember, the blade angle can be changed quite drastically in relation to the fence. You can have either very precise angles adjusting 1 degree at a time or preset common cuts like 15, 30 or 45 degrees.
Can a 10 inch sliding miter saw cut a 6x6?
The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
How big of a piece of wood can a 10 inch miter saw cut?
A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.
Can a 10 inch miter saw cut through a 4x4?
So, is it possible for a 10-inch miter saw cut a 4x4? The answer is clearly, yes. But, given the risk/reward ratio due to the extra inches, this isn't a type of cut you should try to do with a 10” blade.
Will a 12-inch miter saw cut through a 4x4?
The size of the 12” miter saw blade is such that it can easily cut through a 4×4. So, if you want to avoid the extra work, then a 12” saw is recommended.
How do you cut a 4x6?
0:121:14How to Accurately Cut a 6x6 - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst mark the cut location. And use a pencil and rafter square to extend the line around the postMoreFirst mark the cut location. And use a pencil and rafter square to extend the line around the post rotate the stock as needed to line up the square and transfer the line to all sides.
Can a 12 Mitre saw cut a 6x6?
The geometry that makes it a wide, flat cutter works against it with a taller block. No saw could cut through a 4x4 at a 45-degree bevel angle, nor could any cross-cut a 6x6.
What kind of saw do I need to cut 4x4 posts?
The best way to cut a 4×4 post is by using a 12-inch miter saw, 10-inch radial arm saw, both of which can cut completely through a post in one pass, or a standard circular saw that can make precise cuts in two passes with the help of a simple jig.
What size saw will cut a 4x4?
Cutting a 4×4 with a Circular Saw – Guide If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it's the way to go.
What is difference between single and double bevel miter saw?
The difference between a single and dual bevel miter saw is that a single bevel saw can only cut a bevel in one orientation, usually to the left. A dual bevel miter saw can swivel to the left or right, making it possible to cut a bevel in both orientations without the need to reposition the workpiece.
How thick can a 10 table saw cut?
3½ inchesCutting Depth and Blade Size The most common blade sizes for these saws are 10 inches and 12 inches. With a 10-inch table saw, users can often make a maximum cut up to 3½ inches deep (that enables the user to rip a 4×4 in half).
What is the best way to cut a 4x4 post?
0:432:212 Ways to Cut a 4x4 Without a Miter Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipStraight keep it against the squares you make your first. Cut then rotate the board one turn towardsMoreStraight keep it against the squares you make your first. Cut then rotate the board one turn towards you then use the curve you just made to help line up your blade for your second.
How do you cut a wide wood with a miter saw?
0:060:42How To Crosscut Wide Boards on a Miter Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipMini miter saws have a sliding feature for cutting wide boards to use it pull the handle all the wayMoreMini miter saws have a sliding feature for cutting wide boards to use it pull the handle all the way toward.
How thick can a 10 table saw cut?
3½ inchesCutting Depth and Blade Size The most common blade sizes for these saws are 10 inches and 12 inches. With a 10-inch table saw, users can often make a maximum cut up to 3½ inches deep (that enables the user to rip a 4×4 in half).
How do you cut a wide wood with a miter saw?
0:060:42How To Crosscut Wide Boards on a Miter Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipMini miter saws have a sliding feature for cutting wide boards to use it pull the handle all the wayMoreMini miter saws have a sliding feature for cutting wide boards to use it pull the handle all the way toward.
What saw will cut a 4x4?
If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it's the way to go.
Can I use a 7 blade in a 10 miter saw?
If you're using a 7-inch blade in a 7 ¼ inch saw, or a 9-inch blade in a 10 inch saw, then the effect will be minimal. However, toss a 7 ¼ inch blade on a 10-inch saw and you might not be able to cut through your workpiece.
What Can You Cut with a 10” Miter Saw?
So, is it possible for a 10-inch miter saw cut a 4x4? The answer is clearly, yes. But, given the risk/reward ratio due to the extra inches, this isn’t a type of cut you should try to do with a 10” blade. There is some good news, though.
What is the difference between a 12" and 10" miter saw?
A 12” miter saw clearly has a bigger blade. This means that it can do longer cuts faster as well as wider cuts. The cutting capacity is so superior that even the cheapest 12” miter saws on the market will still cut through 4x4s faster and cleaner than the best sliding 10” miter saw.
What Makes the 12” Miter Saw Superior?
If you really want to cut 4x4s reliably, and if you foresee many future projects involving 4x4s, then you’re asking the wrong question. It shouldn’t be a matter of whether a 10-inch miter saw can cut a 4x4, but rather what miter saw is better suited for cutting 4x4s?
How to chop a 4x4 in a single pass?
One way to chop a 4x4 in a single pass is by adjusting the blade guard to essentially increase the saws cutting capacity. If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4x4 post, even when utilizing a 10-inch blade. If adjusting your blade guard is out of the question (and should ...
Why do sliding miters have more range of motion?
Sliding miter saws have more range of motion, because you can tilt the head of the miter saw forwards. This obviously tilts the blade forward, thus increasing the cutting capacity of the miter saw.
Why do you converge cuts in the middle of a 4x4?
By converging multiple cuts in the middle of the piece of 4x4 you avoid stressing the miter saw and the blade more than they can handle.
How to stop a 4x4 saw from kickback?
Bring it down slowly towards the mark, while firmly pushing down on the side of the 4x4 to give it more stability. By pushing the blade slowly into the wood , you’re minimizing the risk of a kickback. After you make your cut on the first side, bring the blade back up and stop the saw.
Which is better, a 12 inch or 10 inch miter saw?
If we compare the blade with 12″ miter saw, the 10″ miter is faster. The 10″ blade will have a higher RPM rate than 12-inch blade on an equal-powered motor. And higher RPMs mean a finer finishing. The 10″ blades are easier to handle, and the cuts they make are less aggressive. We can do more jobs with our 10″ miter saw.
What is a 12 inch miter saw?
Generally, if you consider buying a 12″ miter saw for some larger jobs or power or cutting capacity, the 12-inch miter saw is the creme de la creme. It can do all types of crosscuts on wider and thicker pieces of lumber.
How to cut a 4×4?
We need to follow some precautions cutting 4×4 with miter saw. Let’s go through the steps carefully –
What is a sliding 10 milter saw?
Generally, a sliding 10″ milter saw has a higher cutting capacity, versatility, and torque than a stationary one . The sliding saw can tilt back and forth so you can have a range of motions. And this feature increases the cutting capacity too. Again, when you want excellent crosscuts, and confused about buying a circular saw vs miter saw, ...
How many degrees can a miter saw cut?
Remember, the blade angle can be changed quite drastically in relation to the fence. You can have either very precise angles adjusting 1 degree at a time or preset common cu ts like 15, 30 or 45 degrees. If you want some help figuring out which miter saw is the right one for you, check out our in-depth miter-saw reviews.
How to make a saw blade?
Firstly, start your saw when the head is in the resting position. Then, bring it down slowly towards the mark and again push down firmly to 4×4 for more stability. Now, once you have done with one side, bring the blade back up and stop the saw.
Can a 12 inch miter cut a 6x6?
Generally, it is not quite possible to cut a 6×6 with 12″ inch miter saw. The 12″ miter can cut 4×6 with one pass.
What angle can a 10 inch miter saw cut?
You can also use a 10 inch sliding miter saw to cut 2×4’s at a 45 degree angle. With the same 10 inch blade, you can cut into wood or plywood up to 2 inches, as opposed to just 1.25 inches with a non-sliding miter saw.
Why use a 10 inch blade on a 12 inch miter saw?
There are many 12 inch sliding miter saws available so why should you settle for a 10 inch blade? Because for most home woodworking projects a non-sliding 10 inch miter saw will generally be enough, so it stands to reason that the extra cutting capacity you get with a sliding miter saw of that size should be more than enough to take your projects up a notch.
What size blades do miters use?
Miter saws with 10 inch blades continue to be the most popular size. But is it really a personal preference or just a forced choice on the part of the manufacturers? Let’s have a look at the 10 inch sliding miter saw cut capacity and performance when compared to 12 inch blades and non-sliding 10 inch blades.
How deep can a sliding miter saw cut?
Compared to a non-sliding miter saw, you can expect to see almost double the cutting capacity. You may cut up to 2 inches deep, and 12 inches when crosscutting wide boards and sheets. Sliding miter saws are really worth the extra bucks if you want to be able to work with a wider range of sheet sizes. Preview.
What is the difference between a stationary and a sliding miter saw?
Sliding and stationary miter saws look very similar on paper but it’s the sliding feature that makes a world of difference between the two. Sliding miter saws let you tilt the saw head forward and backward which means you’re able to tackle thicker materials with them.
Can you crosscut with a 10 inch blade?
While a non-sliding miter saw may only let you crosscut a board 6 inches with a 10 inch blade, a sliding miter saw will let you cut almost twice as much. Of course, it depends on the blade whether you can do this in one clean cut or in two cuts starting from both ends. There are many 12 inch sliding miter saws available so why should you settle ...
Can you use a 10 inch blade on a 5.5 inch board?
You can use a 10 inch blade to make right angle cuts on a 5.5 inch wide board. This means that you’ll have no problem working with 2×6 pieces of lumber. However, the thickness of the wood is not the only factor here. While the 10 inch blade on a sliding miter saw can get the job done, if the wood is really dense you might still need ...
Which One to Go for, a Circular Saw or a Miter Saw?
Well, you can cut a 4×4 with a 10-inch blade. But according to the saw you may struggle with different troubles if it is not efficient enough. If you are up to cut a 4×4 with a circular saw, then you may end up having a not so good experience. Also, it requires a lot of work and a lot of time. Again, the work remains sketchy and imperfect.
How about a 12 Inch Blade? Will It Do a Lot Better?
Well, in this case, the 12 inch blade will be a beast to slay the job. Even the thinker, wider and longer stocks also can be cut with a 12 inch blade saw. It is needless to say that even the stationary type of saw with a 12 inch blade can do a 4×4 easier than the 10 inch slide-type miter saw.
Conclusion
Long story short, it is easily predictable that cutting a 4×4 with a 10 inch miter saw requires a whole lot of practice. If you are not a professional carpenter, then most probably you don’t even dare to try on. Then again, a 10-inch miter saw is highly recommended to a mediocre householder for his smaller DIY projects.
How many steps can a 10 inch miter saw cut?
The type of saw and the type of blade are also important things to consider. While a 10 inch blade on a miter saw can cut through a 4×4 in one or two steps, this may not be enough from a practical standpoint. If you want to get the job done faster and smoother you should definitely consider either a 12 inch miter saw of any type or ...
What size blade should I use for a 4x4 saw?
If you want to cut along the grain of a 4×4, regardless of saw, you’re better off with a 12 inch blade. Because rip cuts typically ask for more teeth on your blade, you’ll want a 12 inch instead of a 10 inch. It’s easier to find quality 12 inch blades with up to 60 or 80 teeth for use with standard and compound miter saws than it is to find 10 inch blades with a high TPI.
What Gives the Blade its Cutting Capacity?
If you’re constantly asking yourself “can a 10 inch miter saw cut 4×4” you may be asking yourself the wrong question to begin with. There’s a lot more than just the size of a blade that determines cutting capacity. You have to consider the TPI, the motor power, the type of saw, and even how many cuts you’re willing to make.
How does the kerf of a blade affect the cutting capacity?
The kerf of a blade will also influence the cutting capacity. This will determine the width of the cut that the blade can make. The thinner the kerf, the smoother the cut will be. It depends on the build and the brand whether or not two blades of the same kerf may or may not be able to cut easily through 4×4’s.
Which has more cutting capacity, a stationary saw or a sliding miter saw?
Because of its ability to tilt the blade forward and backward, the sliding miter saw will give you more cutting capacity than a stationary saw. However, even 10 inch sliding miter saws may give you a hard time when cutting a 4×4. They do have a higher cutting capacity, but they might not offer the necessary torque.
Can you use a 10 inch miter saw to cut 4x4s?
If we were to sum it all up neatly, the simple answer is yes, you can use a 10 inch miter saw to cut 4x4s, with caveats. This may be enough information for the weekend carpenter but for people that work on a semi-daily basis with wood there’s more to it than this.
Is it hard to determine the cutting capacity of a 10 inch blade?
Determining the cutting capacity of a 10 inch blade is not hard but it’s the way it handles the task that might interest you more.
What Size Saw to Cut 4×4?
Power saws such as circular saws and miter saws make the cutting job effortless. However, you should have the right tool for the job.
What is a 4x4 saw?
The 4x4s are some of the most common pieces of wood used in construction, particularly fence posts. The 4×4 is both thick enough to be used for fencing, yet still light and easy enough to work with to make the job easier. However, finding the right size blade to make the cuts with your miter or circular saw means doing a little research ...
What is the Best Saw to Cut a 4×4 Post?
A circular saw or skil saw is the best saw to cut the top of 4×4 fence posts on the ground. They are sufficiently accurate and easy to use. The only downside is that you have to make at least two passes to cut through the fence post.
How deep can a table saw cut?
A table saw with a 12-inch blade can cut 4×4 in one pass. However, a 10-inch blade can cut only 3-⅛ inch deep which is not sufficient to cut the 4×4 in one pass. In such cases, you have to flip the lumber and pass a second time to complete the cut. The main advantage of a table saw is its ability to do rip cuts.
What is the advantage of a 12" blade?
Another advantage is the ability to do angle cuts precisely. However, the 12” blade can do the job in a single pass which makes it easier to use and more desirable , especially if you are frequently cutting 4x4s. In addition, the 10” blade on a sliding miter saw can also work just as well.
How to make cuts as precise as possible?
In order to make your cuts as precise as possible, use a speed square to mark the cut line clearly .
What is the advantage of a table saw?
The main advantage of a table saw is its ability to do rip cuts. That means you can cut a 4×4 lengthwise with a table saw or you could also use a vertical bandsaw for this. A bandsaw is a better option for resawing (slicing thin strips of wood).
