Over time, the cable will naturally stretch and the jacket will wear. You can set it up where the pedal hits the floor precisely as the throttle body is at WOT but you will need to make periodic adjustments to accomodate the cable stretch.
Full Answer
Why does my throttle response take so long?
Sometimes a cable can become stretched over time, which will not only delay the response of the throttle, but can also leave the cable more susceptible to breaking. Delayed response may also be indicative of the need to have the cable slack adjusted. 3. Problems with cruise control
What should I do if I have a throttle cable problem?
If you suspect that you may have a problem with your throttle cable, have it inspected by a professional technician, such as one from YourMechanic. They will be able to replace your accelerator cable as necessary.
Can a bad accelerator cable affect the throttle body?
As both cables are connected to the same throttle body, any problems with the operation of one can affect the other. Because the accelerator cable is basically what allows the engine to accelerate, any problems with it can greatly affect the performance of the vehicle.
Is there a drive-by-wire throttle control?
Problems with cruise control While most newer cars use drive-by-wire electronic throttle control, physical accelerator cables are still commonly found on many vehicles out on the road.
How do I know if my throttle cable is stretched?
Some of these issues are:The pedal feels stiff or hard to depress.The pedal sticks and does not release normally.There is slack in the pedal's movement.There is a rough or abnormally low idle.The engine stalls.There is a delay in response when you push the pedal down.More items...•
Can a accelerator cable stretch?
Sometimes a cable can become stretched over time, which will not only delay the response of the throttle, but can also leave the cable more susceptible to breaking. Delayed response may also be indicative of the need to have the cable slack adjusted.
How do you stretch a throttle cable?
0:052:18HOW TO ADJUST YOUR THROTTLE CABLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of thatMoreAnd you can shift the outlet point of the cable to tighten. The cable itself and get rid of that slack you want just a small amount so that you're not stretching the cable.
How tight should throttle cable be?
The accelerator cable tension is usually set so that 2-3mm of free play is present in the throttle grip. Once the correct tension has been applied, the lock nuts should be snugged and any dust covers should be slid back over the adjusters. Cables can be adjusted using the appropriate size wrench.
How long do throttle cables last?
Usually, you can expect to get five years from your accelerator cable before it needs to be replaced. Usually, your accelerator cable won't simply “let go.” You will notice one or more of the following signs: Car jerks when using cruise control. No engine response when you depress the accelerator pedal.
How do you test a throttle cable?
Check Your Initial Throttle Cable Slack To check the free play, roll the throttle forward until it stops and take note of the position, then gently open the throttle until you feel the tension on the cable. The distance from the closed position to the tension point is your free play.
How do you get a slack out of a throttle cable?
0:473:33How To Adjust Your Motorcycle Throttle Cable | MC GarageYouTubeStart of suggested clipEnd of suggested clipAnd one on the throttle housing then twist the throttle. And measure the distance. If throttleMoreAnd one on the throttle housing then twist the throttle. And measure the distance. If throttle FreePlay is out of spec. There are two places that cable slack can be adjusted up here at the throttle.
How do you fix a tight throttle cable?
2:363:44How-To: Fix a Tight Seized Stiff Lawn Mower Throttle Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then just doused it in wd-40. And i just kept working it back and forth back and forth back andMoreAnd then just doused it in wd-40. And i just kept working it back and forth back and forth back and forth until it actually. Got easy to move again so as you can see and now when i.
How do I get my throttle snap back?
0:484:15Throttle grip not snapping back - a new look at things - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just anything really you just push down on it. So you see it's push down stance. Right back pushMoreAnd just anything really you just push down on it. So you see it's push down stance. Right back push down on it snaps right back so you know that it's not the spring.
Why does my gas pedal feel spongy?
Gas pedal feels spongy On older vehicles with the mechanical throttle linkage, the throttle return spring keeps the pedal solid and very easy to control. If the throttle pedal is spongy when you depress it, it could be caused by a broken throttle return spring or one that is wearing out.
How do you adjust the throttle cable on a gas pedal?
0:481:48Throttle Cable Adjustment - Project Integra - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow the adjustment. Itself is actually quite simple all you're going to do is take a 12 millimeterMoreNow the adjustment. Itself is actually quite simple all you're going to do is take a 12 millimeter wrench. And loosen the left. Side and then you can pull that throttle cable.
How do you fix a loose gas pedal?
0:582:03Fixing sloppy gas pedal - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what you're gonna do is zip tie around. And then that's gonna give you the throttle response andMoreAnd what you're gonna do is zip tie around. And then that's gonna give you the throttle response and power back so that's all you do you pull it around make sure you don't put too many on sandwich.
What can a loose throttle cable cause?
Improper cable adjustment and slow acceleration response This can also result in the opposite effect as well, in that the excess slack can create a delayed throttle return response. This can cause more throttle to be applied unintentionally, creating a dangerous situation.
How do you fix a loose accelerator pedal?
0:512:03Fixing sloppy gas pedal - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what you're gonna do is zip tie around. And then that's gonna give you the throttle response andMoreAnd what you're gonna do is zip tie around. And then that's gonna give you the throttle response and power back so that's all you do you pull it around make sure you don't put too many on sandwich.
Why does my gas pedal feel spongy?
Gas pedal feels spongy On older vehicles with the mechanical throttle linkage, the throttle return spring keeps the pedal solid and very easy to control. If the throttle pedal is spongy when you depress it, it could be caused by a broken throttle return spring or one that is wearing out.
How do you fix a sticky accelerator cable?
1:294:53Fixing a Sticky Throttle Cable - MGF, MGTF & Others - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull back the carpet. And pull it out of the clips there touched and silt. Give you a little bit ofMorePull back the carpet. And pull it out of the clips there touched and silt. Give you a little bit of slack. And next we need to try and get lots of oil down.
What is the name of the cable that connects the gas pedal to the throttle plate?
An accelerator cable, sometimes called throttle cable, is a metal braided cable that serves as a mechanical link between the gas pedal and the engine’s throttle plate.
What happens if you wear a cable on a car?
If you notice any damage or wear on the covering, then there is the possibility that the metal cable inside has received damage.
Why do accelerator cables fail?
As the throttle is what controls the power of the vehicle, any problems with the cable can quickly translate into problems with the drivability of the vehicle so it should be inspected as soon as possible. The most common way that accelerator cables fail is that they break.
What is the rubber sheath on an accelerator cable?
The accelerator cable on most vehicles is covered by an outer rubber sheath that protects the braided metal cable inside. Sometimes the cable can come into contact with sharp edges or moving engine components that can wear into the sides of the covering. If you notice any damage or wear on the covering, then there is the possibility that the metal cable inside has received damage. Because the cable is under constant stress any damage to the cable can leave it more susceptible to breaking.
How to tell if accelerator cable is bad?
Usually, there will be a few symptoms displayed when the accelerator cable is having a problem. 1. Damage to the outer covering. The accelerator cable on most vehicles is covered by an outer rubber sheath that protects the braided metal cable inside. Sometimes the cable can come into contact with sharp edges or moving engine components ...
kfd518 Pinnacle OPE Member
I’m having a problem with my 394 throttle. I was attempting to tune it and adjusting the high side it maxed out at around 11,900 slobbering rich. I realized that when squeezing the throttle it will normally only open to about 85-90% sometimes it opens fully to the throttle stop not often that I get the fluke of it opening all the way.
huskihl Sausage Lives Matter
Loosen the bolts and rotate the carb clockwise. If it's not enough, a couple wraps of fine wire just ahead of the crimp will effectively shorten the cable
Creaky limb tree care Super OPE Member
Hi, have you made sure that the cable's outer sheath is sitting correctly in the relevant pockets either end? I have had issues with a 550 before now which wouldn't rev out on full trigger depression. Regards, Toby.
huskyboy Sorta a husqvarna guy..
First I check to make sure it’s seated in the trigger or cable holder like Toby mentioned. Sometimes there is a tear that you can’t see, eventually the cable is exposed and tends to hang up. I try to keep spare cables for the 394/5 and 372 for this reason. They wear out.
