How To Make Your Own Carpet Stair Treads
- Select Your Carpet. Before you start the process make sure you have the right carpet for the job. ...
- Measure The Stairs. Measure the stairs to keep you right, measure the length of the stairs and the width of the stairs to make sure you know ...
- Cut The Carpet or Door Mats. ...
- Backing The Mats. ...
- Attach The Carpet Treads To Stairs. ...
Can You Make your own oak stair treads?
Here are some steps to take to make your own oak stair treads with a blank piece of oak, some power tools, and a lot of patience. Purchase an oak plank that has approximately the same type of grain pattern as the rest of the treads.
How do you secure stair treads to stringers?
Secure the treads to the steps of the stringers with 2.5 in (6.4 cm) screws over each stringer. For instance, you could cut 1 in × 10 in (2.5 cm × 25.4 cm) lumber to the width of the stairs, and use this for your treads. For a special touch, use two boards and leave a 1⁄8 – 1⁄4 inch (0.32–0.64 cm) between them.
How to cut stair treads to size?
To put this edge on the stair tread you will need to use a router with the rounded-over bit. This is the reason you also cut the tread 2 inches wider than normal. Once you use the router it will be at the size you want. If not, you can always sand the edge down to the dimensions you prefer.
What is the difference between stair stringers and treads?
Stringers are diagonal 2 in × 12 in (5.1 cm × 30.5 cm) boards that support people's weight as they walk up the stairs. Treads are the top baseboards onto which you step, and risers are placed perpendicularly under each tread.
What can I use for stair treads?
What Wood Is Best for Stair Treads?Oak Stair Treads. Oak is a common type of wood for stair treads. ... Hickory Stair Treads. Hickory is another common choice for wood stair treads. ... Maple Stair Treads. Maple's tan and white hues make it a popular choice for a range of wood products. ... Poplar Stair Treads. ... Walnut Stair Treads.
Can you make stair treads from hardwood flooring?
14:0837:24How to make stair treads out of hardwood floor - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the bull nose it's going to cost you a lot of money but if you want to make your own I've gotMoreWith the bull nose it's going to cost you a lot of money but if you want to make your own I've got some some leftover hardwood floor from a project that one of my family members did.
Can Plywood be used for stair treads?
While ¾” thick plywood or OSB is considered sufficiently thick for subfloors, it is not uncommon to use a thicker material for the stair treads. One inch of total plywood thickness is ideal and can be made from two layers of ½” plywood, bonded together.
How do you make treads?
0:009:07How to make stair treads from scratch using rough lumber (Part 1 of 2)YouTubeStart of suggested clipEnd of suggested clipI was to add a one inch tread on every one of the treads that is already there so I did not have toMoreI was to add a one inch tread on every one of the treads that is already there so I did not have to recalculate stringers or anything like that. So I bought rock-cut oak boards from a mill.
What type of wood is best for stair treads?
While Pine is softer than Oak and other hardwoods, Pine is nevertheless one of the best woods for stair treads. Pine hardwood floors and stair treads have incredible longevity – you'll find many homes with Pine floors that are centuries old.
Do stairs need nosing?
Run Requirements You are not required to have a nosing/overhang on your stair treads. But if your stairs don't have a nosing you are required to have a tread that is at least 11 inches long.
How do you make cheap stair treads?
1:3710:20DIY Stairs Makeover for Under $200 with Full Cost Breakdown!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so the magic trick in creating these stairs for under 200 bucks is using solid oak strips forMoreOkay so the magic trick in creating these stairs for under 200 bucks is using solid oak strips for the bullnose. And quarter inch oak plywood.
What thickness should stair treads be?
The standard thickness of stair tread is up to 1-1/16” of an inch, although 1” stair treads are extremely common and found at all big box home reno stores. Remember also that stairs must have a minimum depth of 10” and minimum width of 24”. What is this? Many stores offer treads that are ¾” thick.
How thick should plywood be for stair treads?
The thickness of your plywood stair treads should be anywhere from 1” to 1 ½” in thickness. It's important to invest in quality plywood. As a rule of thumb, always remember that the fewer stairway stringers you use, the thicker you want your stair treads to be.
How do you build wood stair treads?
0:006:07How To Install Prefinished RetroFit Stair Treads from Stair-Treads.comYouTubeStart of suggested clipEnd of suggested clipInstalling pre-finished stair treads from stairtrez.com. Our first step is to remove the old carpetMoreInstalling pre-finished stair treads from stairtrez.com. Our first step is to remove the old carpet exposing the sub tread. Below.
What goes on first treads or risers?
riserDo work at least one riser ahead before installing treads. Installing two risers is one way to ensure proper strength and performance. The important thing is to remember to install riser, tread, riser, tread or install the risers first.
How do you make a stair tread template?
2:1512:12Make Your Own STAIR JIG - QUICK, CHEAP & EASY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'm going to make a three foot. Piece. First then i'm going to make two probably six inch piecesMoreSo i'm going to make a three foot. Piece. First then i'm going to make two probably six inch pieces on the end so i can adjust it out. So let's get that done. Okay we got a three foot.
Is it hard to put hardwood on stairs?
2:0111:09How To Install Hardwood on Stairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut that can vary as well so you cut off the the piece you need the length you need then I splicedMoreBut that can vary as well so you cut off the the piece you need the length you need then I spliced together some flooring for the center row and I use a solid strip again on the back row.
Can you put engineered hardwood on stairs?
Engineered hardwood is often sold prefabricated into risers and stairs, so you need only to purchase the premade pieces in the color and dimensions you want. Once you've received them, you need to begin the process of preparing your existing staircase so you can attach the risers and the treads.
How do you install hardwood stair treads?
0:2815:09Professional Stair Tread & Riser Installation - Complete Install ProcessYouTubeStart of suggested clipEnd of suggested clipBut all you do is simply loosen your little wing nuts on here push it tight to the side. And then reMoreBut all you do is simply loosen your little wing nuts on here push it tight to the side. And then re-tighten. Them you're going to do this on both sides. Until you're satisfied.
Is Hickory good for stair treads?
Hickory wood is extremely durable and has a color ranging from white to pale or reddish brown. We use only the highest quality hickory wood in our stair treads and produce our treads with state-of-the-art equipment.
Can I make my own stair treads?
I have enough 5/4 x 4 to make all of the stair treads that I need. Is it advisable to do this. Will they last. I need an 11 1/4" finished size. So I was thinking to rip the pieces to three inches and laminate them. Is there anything special considerations in constructing them? Special glues? Do I need to use biscuits?
I Am Finaly Done (Five Photos)
Thank you to all who contributed. I will attempt to post some photos of the completed stairs. I don't particularly care for the look of oak. But hay, its a very good material for floors and stairs. Best of all it was free (from our building lot). Unless you count all of the hours milling, drying, jointing/planing. I am quite happy with the results.
Stair Runner Dilemma
When I started my search for stair runners, I came up with two conclusions.
Determine the Size of Your Stair Runner
Each of our stair treads measures 11&1/2″ deep and 36″ wide. The treads above come in two sizes – 9″ by 26″ and 9″ by 33″. Since I didn’t want to cover the entire stair tread, we opted for the smaller size stair tread. This gives us about 5 inches on either side of the carpeted area and a few inches behind each one.
Prep Your Surface for Anti Slip Treads
Clean your stairs before applying. We used Mr. Clean mop solution to get rid of all the dust and grime before starting. Make sure the surface is completely dry before you start adhering to your treads.
Installation
Unfortunately, I don’t have a pic of this part because it was back before my blogging days where everything gets a pic! However, follow the instructions on the double-sided adhesive. We cut out a strip for each long edge and each side edge. Adhere to the carpet and then to the stair tread.
How do they hold up?
We’ve had them for a few years now and they are holding up beautifully! There are a few edges that look a little frayed, but nothing that is very noticeable. I’m impressed with the quality and durability.
Tips
Make sure the material you are using for the landing is in place before you lay out the steps to avoid trip hazards.
Warnings
Always check building codes that apply in your area. These may stipulate particular minimums or maximums for step runs and rises, the number of stringers that are necessary, etc.
About This Article
This article was co-authored by Lui Colmenares. Lui Colmenares is a handyman and licensed home improvement contractor for Mr. Handy NYC based in New York City, New York.
