Can you install tile without grout lines?
Well, the short answer would be a simple no – you should not attempt to install tile without grout.
Do marble floors use grout?
Regular plywood subfloors are not suitable for installing tile. Marble tiles can be butted tightly together for an ultra-smooth look, or have gaps between the tiles that you fill with grout. If you go the grout route, be sure to use unsanded grout because sanded grout can scratch the marble during installation.
Is grouting necessary?
Grout is an essential part of your tile installation and choosing the right grout can make all the difference between an installation that looks and performs beautifully over time and one that rapidly deteriorates into a dangerous eye-sore.
What is the thinnest grout line possible?
Generally speaking, under this standard, most calibrated tile should not have a grout joint smaller than 3/16”. Most rectified tiles should have no grout joint smaller than 1/8”. The smallest grout joint you should ever have is 1/16” and is usually only applicable in stone installations.
Is there a special grout for marble tile?
Grouting marble tiling There are primarily two types of grout for natural stone, further divided into sub-types of grout. Both cementitious and epoxy grout are suitable for marble with some precautions. Cementitious grout is by far the most common option for natural stone.
Is marble tile hard to install?
Installing marble tile is similar to installing other types of tile, such as ceramic or porcelain. In fact, the steps are pretty straightforward. After preparing the subfloor, glue down the tiles, grout, then seal.
What is the smallest grout line for tile?
1/16″Smallest size grout lines should not be less than 1/16″. This is an acceptable space that can be properly grouted. When the space between tiles is so little like 1/32″ which is often referred to as “credit card lines” or “penny lines”, it's not possible to fill that space all the way through the bottom of the tile.
Can I use caulk instead of grout?
Grout is only used to fill the joints between tiles, while caulk can seal seams in many spots—along baseboards and crown molding, on windows to stop leaks and drafts, and anywhere two construction materials meet, even on outdoor concrete.
Can you install tile without spacers?
Tiling without spacers is not only extremely difficult but also time-consuming. You need to stop constantly and adjust the tiles so that you get an even layout. With a tile spacer, on the other hand, you will spend less time agonizing over the width and accuracy of your lines.
What kind of tile does not require grout?
Daltile developed Campisi with Cliks to provide homeowners the best of form and function. These tiles feature patented tongue-and-groove interlocking joints and built-in grout that simply clicks together so no mortar or grout is needed.
How much space do you need between marble tiles?
Spacing the Tiles The spaces between your tiles should be no more than 1/8-inch wide (a 1/16-inch space is better, if the edges of your tiles are straight enough to accommodate it). Always use plastic spacers to get that consistent line.
What happens if grout lines are too thin?
Grout lines that are too thin will also affect tile expansion and contraction. With there not being much leeway for the tiles to move, they can end up cracking or chipping under the pressure as they push up against each other, or buckling and falling off your shower wall.
How do you clean grout on marble floors?
0:091:27Grouting Help : How to Clean Grout on Marble Tile - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd cleaning products you could put on it the best thing to use is some warm water with just aMoreAnd cleaning products you could put on it the best thing to use is some warm water with just a couple teaspoons of mild laundry detergent. Basically you just want to spray it on your surface.
How do you Regrout marble floor tiles?
InstructionsRemove the Grout. Using a grout saw or an electric tool such as a Dremel with an appropriate attachment, begin to remove the grout from between the marble tiles. ... Vacuum and Mop. ... Apply New Grout. ... Rinse Away Excess Grout. ... Seal the Grout Lines.
How do you seal a marble floor after grouting?
Seal the Grout Joints Brush the marble sealer onto the grout joints as you complete each small section of tiles. Dip the foam brush lightly into the marble sealer, then run the thin edge of the brush along each of the grout lines. Use the broad edge of the brush to wipe up any excess.
Should I seal a marble floor?
The marble tile should be sealed using a neutral pH breathable sealer after installation. The sealer will need to be reapplied periodically, recommended every 12 months or so.