Trex products should not be ripped to reduce thickness, but can be ripped to reduce width. As long as the board can still be installed per the installation instructions, the warranty will be valid. Please use care when fastening ripped boards, as pre-drilling may be necessary.
How to repair deep scratches on Trex deck?
Here are a few ways to keep scratches at bay and maintain your deck:
- Use a woven rug designed for high-traffic spaces. A woven rug will help keep foot traffic from shoes from doing damage. ...
- Place pads under pieces of furniture that live on your deck. ...
- Put furniture away when it’s not in use. ...
- Use a broom instead of a shovel to clear leaves, snow or other debris. ...
How to restore faded composite decking?
Take the following steps to clean your deck appearance:
- First remove all the furniture on the outdoor deck to create a clear working space for you. ...
- Spray the deck down with warm soapy water or matching detergent, and carefully cover the entire deck area with a solution. ...
- Rinse the whole composite deck thoroughly with clean warm water. ...
How to clean composite decking?
Ways to Clean Common Decking Issues
- Mildew & Mold. Mold and mildew will not damage composite decks. ...
- General Debris. Debris is a pain to get rid of on your deck, especially when you have trees nearby! ...
- Dirt Between Floor Grooves. The small spaces and grooves between the deck sometimes trap grime and dirt over time. ...
- Beverage & Food Stains. ...
- Grease & Oil. ...
- Pollens. ...
- Ice & Snow. ...
How to repair composite decking?
How to Repair a Composite Deck
- Remove Composite Deck Boards. You should use a pry bar to remove the nails and screws that hold the deck boards in place. ...
- Replace the Deck’s Joists. The joists which are the cross beams that hold the deck boards in place should be examined for any damage or repair that may ...
- Reinforce Deck Posts. ...
- Replace Damaged Composite Deck Boards. ...
Can you damage composite decking?
Composite decking material is softer than natural wood and therefore can be “etched” more easily. Once the material has been “opened up”, this can lead to a host of other issues including chipping, sun damage, and mold staining of the plastics inside the opening.
Can composite lumber be ripped?
You can use any standard rip blade with 24 teeth to cut your composite boards. Most composites (TREX and others) are primarily plastic or plastic and wood. They are actually easier on tooling than hard wood.
What are the negatives about Trex decking?
First, composite decks can be expensive to install. They also require more cleaning and maintenance than traditional wooden decks, as they can stain and fade over time. Additionally, composite decks may not be as durable as advertised and can be susceptible to damage from weather and insects.
Can you rip deck boards?
Whether you're renovating or building a new deck for your yard, you've most likely come across the term “rip cut” when it comes to cutting wood or composite deck boards. When you rip cut a board, you're cutting along the length of the board with your saw.
Does Trex decking expand and contract?
As a direct result of temperature change our composite decking will both expand and contract as temperatures rise and fall.
Can you lay Trex directly on concrete?
Can composite decking (such as Trex) be installed over concrete? Yes. In most cases you can lay composite decking over concrete (keeping in mind you'll have to build a substructure that allows airflow and drainage).
How long will a Trex deck last?
25 to 30 yearsTrex and TimberTech Composite Decking Warranties Composite decks have a lifespan of at least 25 to 30 years — and their manufacturers have warranties to match.
Does Trex warp in sun?
Trex decking resists termites, won't rot, warp, or splinter-and never needs staining or painting.
Why is my Trex deck bouncy?
A: A “bouncy” deck is usually caused by long joists between beams. Assuming you can access the support framing, you can strengthen the deck by installing rows of blocking cut to fit tightly between the joists, spaced every 3 to 4 feet along the span.
How do you rip up decking?
Demolishing Your Deck in 7 StepsTake Down the Handrails. Once your deck is totally clear, you can begin with removing the rails. ... Pry Off the Deck Boards. ... Cut the Deck Frame Away from Your House. ... Cut Joists Off. ... Remove Hanger Boards. ... Dig Out Support Posts. ... Pull the Steps Apart.
How far can Trex decking overhang?
Trex is a popular composite material with a maximum overhang of 102mm or around 4 inches. Between one and two inches of deck board overhang is ideal when you attach an outer fascia board, or at least 1 ¾” to 2 ¾” of overhang before installing the fascia.
How much does it cost to tear down a deck?
The national average price of deck removal is around $850, including debris disposal. Generally speaking, you can expect to pay $2-$6 per square foot to remove your deck, or around $600-$1,000 for the whole project. However, your exact deck removal cost can vary.
Is composite wood good for outdoor furniture?
In an outdoor patio furniture situation, composite wood is better able to resist changes and damage caused by exposure to the elements. It won't bend and warp at the same rates as natural wood, nor will it fade in the same way that the other material does.
How do you replace composite deck boards?
1:072:43How to Resurface a Wood Deck with Composite Decking - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext install the middle boards we cut ours to length. Then install boards from the breaker board outMoreNext install the middle boards we cut ours to length. Then install boards from the breaker board out to the perimeter boards.
Can you use composite deck boards for railings?
A composite deck board for a drink rail is a fine way to maximize the enjoyment out of your deck.
How do you rip deck boards?
1:152:27HOW TO RIP A BOARD QUICKLY WITH JUST YOUR CIRCULAR SAWYouTubeStart of suggested clipEnd of suggested clipSo what you're gonna do set your song to where it's lined up with the edge of 2 inches. You'reMoreSo what you're gonna do set your song to where it's lined up with the edge of 2 inches. You're taking you on you're going to pinch. Your blade base. And you want to slide your finger.
When to stop decking work?
This can make cutting and securing more difficult. If the decking material begins to get warm to the touch as the day goes on, you may want to stop work and continue the project the next morning.
How much space between decking boards?
Between end-to-end boards, allow a 3/16-inch space.
Why do builders like composite decking?
Builders like composites because they are relatively easy to install–the materials are very consistent in size and quality, come in lengths up to 20 feet long, and are not prone to warping and cracking. Composite decking won’t rot or splinter (an extra bonus for bare feet).
Does composite decking rot?
Composite decking won’t rot or splinter (an extra bonus for bare feet). New styles also have fire prevention technology incorporated into the composite, which reduces the risk of house fire during cookouts and makes them less of a fire hazard where wild fires can be a threat.
Is vinyl decking a low maintenance product?
Vinyl decking is yet another low-maintenance option, although one that offers a particularly non-traditional deck. Installation differs as well. In general, first an aluminum or vinyl track is installed across the joists, and then top pieces are snapped into place. From an environmental standpoint, composite decking is considered a “green” product because it is constructed with recycled materials and is very durable.
Can Trex be cut?
Composite decking such as Trex can be cut, drilled, and fastened just like traditional wood, but there are a few tricks you should know to make your project easier, and provide a more professional finish. Composite decking can mimic the look of natural wood. Trex.
Can composite decking be stained?
With others, it’s best to simply view them as a new material. If you’re not satisfied with the color choices, or if you would like your deck to match your house, most products can be stained or painted, as specified by the manufacturer. Some may fade more than others.
How far apart should Trex be installed?
Trex can be installed over timber, steel or aluminum substructures with joist centers at a maximum of 400mm apart. If building over a timber substructure, you should consider using Trex®Protect™ self-adhesive butyl tape to prevent moisture damage.
How far apart should Trex hideaway screws be?
The Universal Fasteners connect two boards together if you drill downwards, directly into the joists. They should be no more than 25mm from the end of the board.
Can you use Trex fascia boards on patio?
Install Trex® Fascia boards to the edges of your patio to give it a more polished look. This finishing touch is now available to match every Trex decking option—so whatever you choose, we’ve got you covered. Just like that, you’re installed—with decking handrails and balustrade next on the list. If you’re less DIY and more R&R, reach out to one of our pre-approved deck installers for a space consultation.
What to use to remove tannins from deck?
If you clear the debris from your deck and notice tannin bleeds have caused discoloration, you can use a deck brightener to remove the stains. These deck brighteners contain oxalic acid, which removes tannins. Just ensure your deck is dry before applying.
How much pressure should I use to pressure wash composite decking?
If you pressure wash your deck, keep it on the lowest setting possible—no more than 3100 psi with a fan tip. Composite decking is much softer than natural wood. A pressure washing at too high a setting can encourage chipping, sun damage, and mold staining. Be sure to spray no closer than 8 inches away from the wood.
Can you use soapy water on Trex decking?
When cleaning your decking, be sure to use the correct cleaner when making your soapy water. Otherwise, you could cause surface damage that affects the appearance of your Trex deck. Composite decking such as Trex decking is porous and needs an oxygenated cleaner that can clean inside the deck and the surface.
Does composite decking need to be cleaned?
While composite decking requires less maintenance than other deck materials, it still requires cleaning to keep it looking fresh, especially after heavy snowfall or storms. Leftover debris can leave behind dirt, mud, and mold if not cleaned up properly.
Is Trex decking hardy?
Trex is an industry leader in hardy composite decking, which requires less daily maintenance than organic lumber decks. However, if your Trex decking has been through a few seasons already, it may be due for some basic care and restoration to get it back to full health. In this guide, we’ll go through the best basic practices for how ...
Does Trex decking need maintenance?
A deck transforms any outdoor space into a great year-round spot for gatherings and parties with friends or family. However, once you’ve installed your perfect decking, it does require some maintenance to keep it in tip-top condition. Trex is an industry leader in hardy composite decking, which requires less daily maintenance than organic lumber ...
Can you dry water off a deck?
Generally, hard water is something to avoid. If there is no other option, you can dry the water from the decking using a dry cloth. If there are already spots on the decking caused by hard water, you can remove them using white vinegar as a cleaning solution.
