CAN/ULC S536-04: The Standard for Inspection and Testing of Fire Alarm Systems Description Building codes in Canada typically require fire alarm systems to be installed in accordance with CAN/ULC-S524, verified in accordance with CAN/ULC-S537 and is inspected and tested in accordance with CAN/ULC-S536-04.
Full Answer
Is the fire alarm system ulc-s536 compliant?
YES NO C The entire Fire Alarm System has been tested and inspected in accordance with CAN/ULC-S536, Inspection of Fire Alarm SystemsYESNO N/A D Fire alarm system documentation on site. YES NON/A
What is can/ulc-s536 and why is it important?
The inspection and testing procedures outlined in CAN/ULC-S536 ensure the fire alarm system and the various system components are still working correctly to provide an early warning of fire or other emergency conditions, enabling building occupants to act and evacuate safely.
What is the ULC code for annunciator and remote trouble unit?
E2.7 ANNUNCIATORS OR SEQUENTIAL DISPLAYS CAN/ULC - S536-04 E2.6 ANNUNCIATOR AND REMOTE TROUBLE UNIT TEST AND INSPECTION (Reference: Clause 5.1.4, 5.4.1) Fill out one per annunciator and remote trouble unit.Led type annunciator and or super warning unit.
How often must a fire alarm system be tested in Canada?
How often must a fire alarm system be tested in Canada? On an annual fire alarm test to Canadian Standard CAN/ULC-S536-04 (-13), is it permissible to skip devices that are either hard to reach or inaccessible for other reasons (i.e. a tenant in a multi-residential occupancy refuses access or isn't home)?
How do you test a fire detection system?
To Test Your Fire Alarm Using The Alarm Panel KeyInsert the test key in to the bottom of the fire alarm point.At the panel, turn the key anti-clockwise.Access LED illuminates.Pres red silence key.Push the fire alarm point upwards to reset.Press the green reset key on the panel.More items...
How often do fire alarms need to be tested Ontario?
every six monthsInspection and servicing of the fire extinguishing system shall be made at least every six months by properly trained and qualified persons in conformance with Ontario Fire Code, Section 6.8. 1.1.
What is a fire alarm system acceptance test?
You must test smoke detectors and smoke alarms in place to ensure smoke entry into the sensing chamber and to verify an alarm response. You may test with smoke or listed aerosol, acceptable to the manufacturer of the smoke detector or smoke alarm and identified in the manufacturer's published instructions.
What is CAN ULC S524?
CAN/ULC-S524 covers the requirement for the design and installation of fire alarm systems with or without voice communications capability. This Amendment contains clarifications and revisions to enhance the requirements in the 2014 Edition.
Can ULC S536 13 inspection and testing of fire alarm systems?
ULC SUPERSEDED - CAN/ULC-S536-13 Standard for Inspection and Testing of Fire Alarm Systems Fifth Edition. This Standard prescribes requirements for the inspection and testing of fire alarm systems and specifies the devices and functions to be inspected, tested, and documented for the periodic inspection and test.
How often do fire suppression systems need to be tested?
To test the effectiveness of a fire sprinkler, you should conduct sprinkler testing every three months. The vane and pressure switch must be tested every six months. If you want full testing and tagging of your fire sprinkler, then you can schedule a testing appointment once a year.
What type of testing is performed soon after a fire detection and alarm system is installed?
The acceptance testEvery device within the system is tested, whether initiating, notifying, or fire panel. The acceptance test is only done once, right after installation and before the building is occupied. The only exception is if the building undergoes renovations, after which the fire alarm system must be acceptance tested again.
What is fire alarm system PDF?
The primary purpose of fire alarm system is to provide an early warning of fire so that people can be evacuated & immediate action can be taken to stop or eliminate of the fire effect as soon as possible. Alarm can be triggered by using detectors or by manual call point (Remotely).
Can ULC S537 verification of fire alarm systems?
The verification procedures outlined in CAN/ULC-S537 ensure the fire alarm system and the various system components were installed properly and are working correctly. Verification takes place when new fire alarm systems are put in place and when additions or modifications are made to existing fire alarm systems.
Can ULC S552 standard for the maintenance and testing of smoke alarms?
CAN/ULC-S552 provides requirements for the inspection, testing and maintenance of smoke alarms that are powered by batteries or by permanent connections to electrical circuits and installed within dwelling units as well as within sleeping rooms or areas that are not part of dwelling units.
Which ULC standard covers the installation of fire alarm systems?
CAN/ULC-S561 standardThe CAN/ULC-S561 standard also covers how your fire alarm monitoring panel is installed in your building to ensure its security.
What are the requirements for smoke alarms in Ontario?
By law, every home in Ontario must have a working smoke alarm on every storey and outside all sleeping areas....Avoid putting smoke alarms too close to:bathrooms.windows.ceiling fans.heating and cooking appliances.
Who is responsible for changing smoke detector batteries Ontario?
Smoke alarms are very important for the safety of you and your neighbours by giving early warning of fire. Your landlord is responsible for installing smoke alarms and keeping them in working condition, including testing, repairs and replacement as necessary.
How many smoke detectors are required in a home in Canada?
Install smoke alarms in each bedroom, in the hallway outside the bedrooms and on each level of your home, including the basement in line with the appropriate Provincial or Territorial and Federal Fire and Building Codes.
Are hardwired smoke detectors required in Ontario?
The Ontario Building Code has required direct-wired smoke alarms be installed in all new home construction since 1986. When smoke alarms are being replaced, the replacement unit must not reduce the level of detection required by the Building Code in effect at the time of construction.
Where is the reference clause in CAN/ULC-S536-04?
The reference Clauses in CAN/ULC-S536-04 appear in Section 5.7.11 entitled “Conventional Circuit End-of-Line Device”:
Who inspects fire alarms?
The daily and monthly inspection and testing of the fire alarm system is normally conducted by personnel appointed as the Fire Safety Director or Deputy Fire Safety Director (or their designates) in your building’s Fire Safety Plan. These tests are outlined in this FAQ .
What are the changes to the fire alarm testing standard?
The changes to the testing standard are significant in one major respect. They will increase the time required to perform the annual test and inspection on all supervised and addressable fire alarm systems and ultimately impact the cost to the building owner for the service.
How many types of isolators are there in fire alarms?
First of all, you have to recognize that there are now THREE types of isolator modules available for use in a fire alarm system. Let’s look at each one and examine the suggested testing methods:
How to test for ground fault in Canada?
On a conventionally wired system, you have to short both sides of each initiating and indicating (NAC) circuit to ground. On an addressable system, you have to short both sides of the SLC (or addressable loop) to ground as well as any conventionally wired NAC's. The same test must be performed at each end-of-line device.
Where are sprinkler monitors located?
These are predominately located in the building's sprinkler room and used to supervise alarm valves, flow switches, and tamper switches on sprinkler riser valves, fire pump valves, back-flow preventers, and the like. You should also check stairwells for valves and flow switches. Monitor modules are normally mounted on 1110 or 4X4 steel boxes. Some (but not all) will be identified with the zone and circuit numbers on the plastic (or metal) covers.
What is a trouble signal on a fire alarm?
In most cases, this must be addressed by trained service personnel. Examples of a "trouble" signal are: AC power failure, battery trouble, ground fault, indicat ing circuit "open", signal circuit "short" or "open".
