Can I cut down my Curtain Pole?
Yes, all our standard metal curtain poles can all be cut down to your required size with a hacksaw. We suggest wrapping masking tape around the metal rods where you need to cut to help mark your cut on the shiny pole and it as protects your pole if you slip with the hacksaw.
How do you cut a curtain rod with a saw?
Make sure your hold the drapery pole firmly in place while you cut if you're using a hand saw. To begin, make a mark on the drapery rod at the point where you're going to make your cut. Then, wrap two inch masking tape around your rod over the mark you just made. You'll want your saw to cut through the masking tape and then through your pole.
What is a metal extendable Curtain Pole?
Metal extendable poles are available for use where you may not wish to use a permanent curtain pole fixing, that has been cut to size. A pole may be purchased in the size range for the length your require.
What is the length of a curtain pole?
52cm (21”) This measurement gives you the length of the curtain pole minus the finial length, as shown in the diagram. Curtain poles are manufactured in set lengths, so if your measurement differs from a standard length, order the next size up from your measurement and cut to size if required.
How do you cut a metal curtain rod?
Most hollow core metal drapery rods can be cut using a hacksaw with a fine cutting blade. Or, as long as you have a fine metal blade, you can use a powered miter saw. Make sure to buy metal curtain rods that are hollow core if you plan to cut them to size yourself.
How do you cut a aluminum curtain track?
If you need to cut your track to fit your window, use a fine tooth saw or hacksaw. To provide an overlap, the track must be cut to allow sufficient length for each half of the window plus an additional 10cm on one half of the track.
Can you cut a curtain pole to size?
All metal and wood poles can be cut down to size, but remember that once cut, they cannot be returned to store.
Can you cut a fixed curtain pole?
Cut the Curtain Rod The majority of cheap rods out there are hollow, so you should have no problems cutting through them. You don't need a power tool to cut the rod, instead, you can use a hacksaw. Although a lot of folks use hacksaws for cutting wood and plastic, they were invented to cut metal.
How do you saw a metal pole?
1:222:34How To Cut Metal - Ace Hardware - YouTubeYouTubeStart of suggested clipEnd of suggested clipTowards you and start cutting. And allow the saw to do the work. If you push too hard. You'll. FindMoreTowards you and start cutting. And allow the saw to do the work. If you push too hard. You'll. Find then it'll bind as well. But it's back and forth even strokes.
Can you cut a metal pole with a hacksaw?
Hacksaws work by simply moving the blade through the metal backwards and forwards in a regular 'sawing' action. The C shaped handles are relatively cheap to buy and the wide range of blades available enables a wide range of profile thickness and metal grades to be cut easily.
How far should a curtain pole extend past window?
How long should the pole be? This can be subjective and is influenced by obstructions around the window area. But as a guide the pole should extend about 15-20cm (6-8in) beyond the window recess on each side. And it should be fitted symmetrically relative to the window opening.
How much should a curtain rod overhang?
General Installation Recommendations. When installing curtain rods, hang the rod so that it extends at least 3 or 4 inches beyond the window on each side. This allows your curtains to overlap both the window and the wall to prevent light from leaking in around the window's edges.
How far should a curtain rod extend past window?
As a general rule, drapes will be open during the day, so make sure the curtain rod extends at least four inches on each side of the window's inside frame. To create the illusion of a wider window, extend the rod up to 10 inches beyond the window's frame.
How do you join a metal curtain pole?
0:020:42Fitting Curtain Poles - How to join 2 lengths of curtain pole - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd it's very simple you place the joining splice into the end of one piece of bolt and pushing pinMoreAnd it's very simple you place the joining splice into the end of one piece of bolt and pushing pin halfway. Along take the other piece of pole. And then just push the two pieces together.
How do you cut a flexible curtain track?
0:263:38REVIEW / HOW TO: Flexible Curtain Tracks - More Privacy & Less Noise!YouTubeStart of suggested clipEnd of suggested clipSo i'm just going to use some tin snips. And then you basically snap it onto those um mount pointsMoreSo i'm just going to use some tin snips. And then you basically snap it onto those um mount points and you just basically do it.
How do you cut a curtain pole straight?
3:109:20Bespoke fit! Fitting a curtain pole - DIY tips and tricks. - YouTubeYouTubeStart of suggested clipEnd of suggested clipI've just hummed in all of it I'm going to cut out. And I do this simply using a hammer and a sharpMoreI've just hummed in all of it I'm going to cut out. And I do this simply using a hammer and a sharp chisel just use the edge of your chisel. Around the line to mark.
How do you cut an aluminum boat?
2:1012:35How to cut aluminum - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo an angle grinder with a cut off wheel on it. Works great the downfall to doing it with an angleMoreSo an angle grinder with a cut off wheel on it. Works great the downfall to doing it with an angle grinder.
How do you install a recessed curtain track?
0:225:56Silent Gliss 6243 Ceiling Recess Curtain Track - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe tracks climb already pre-drilled every twenty or forty centimeters apart so you can to see theMoreThe tracks climb already pre-drilled every twenty or forty centimeters apart so you can to see the holes here. So you just screw straight directly into the ceiling recessed.
How to cut a pole with a circular saw?
Cut the pole. If using a circular saw, squeeze the trigger hard and push the saw firmly, evenly and slowly into the pole until it has cut all the way through. With a hacksaw, this will take much longer, as you will be relying on the power of your arms and hands.
How to separate a melted pole?
Knock the pole with a hammer to separate it if it doesn't break cleanly once your cut is done. Some of the melted material may stick in the cut, but it is brittle and will break easily.
How to get a good grip on a bandsaw pole?
If the pole is small enough to fit in a bandsaw, set it across the bandsaw deck, start the saw, then get a good grip on the pole on either side of the blade and push it through firmly and slowly.
Can you cut a steel pole?
Steel poles are a common sight as flagpoles, railings and fences or supporting scaffolding or basketball nets. To fit and install any of these things, it may be necessary to cut a steel pole down to size. Since steel poles are typically hollow, cutting them is less work than it might appear from the thickness of the pole itself.
How to cut a cylinder with a hacksaw?
As posted above, use masking tape around where you want to cut, draw the cut line on this and then use the hacksaw. Take your time - cutting into the cylinder takes time. Once you've done that, cutting through the cross section is easier because there's less metal to cut.
Can you attach finials to metal?
Yup I'd recommend that. I didn't have a metal file at the time so didn't bother. Had no issues with attaching the finials.
How to cut a drapery rod?
Then, wrap two inch masking tape around your rod over the mark you just made. You'll want your saw to cut through the masking tape and then through your pole.
How long should a curtain rod be?
You'll quickly notice that most curtain rods come from the manufacturer in several predetermined lengths like four foot, six foot and eight foot. This works great if your window is really close to one of these sizes, but if you need a slightly smaller length of drapery pole for your project, then you'll need to trim it before you install it.
How deep should a pilot hole be for a drapery rod?
Your mark should be at the center point. You can use a 1/8 inch drill bit to make the pilot hole, or you can simply tap in a nail. The pilot hole doesn't need to be very deep, usually a half inch or so is all you'll need to start the finial into the end of the drapery rod. Many drapery hardware products can be cut to size before they are shipped ...
How to cut hollow core drapery?
Solid metal drapery hardware is best cut to size by the manufacturer. To trim your hollow core product to size, simply mark the point where you need to make your cut and use your saw. Before you cut, make certain to remove any finial adapters or plugs from the end of the pole so you can slide them back on when you're finished. ...
Can you trim a curtain rod to fit a window?
Both decorative wooden drapery rods and metal curtain rods can be quickly trimmed to perfectly fit your window. And, the process is similar for both the wood and metal styles. Before you begin, make sure you have access to the appropriate saw as well as safety glasses or goggles.
Can you use a miter saw to trim drapery?
For trimming wood drapery rods to size, you'll get the best results with a powered miter saw. If you don't have a miter saw, you can always use a hand saw. Make sure your hold the drapery pole firmly in place while you cut if you're using a hand saw.
Do you need to trim drapery poles before installing?
This works great if your window is really close to one of these sizes, but if you need a slightly smaller length of drapery pole for your project, then you'll need to trim it before you install it. The task of cutting drapery hardware to size can seem a bit scary to some home owners.
What is the largest diameter metal pole?
50mm metal poles are the largest diameter we offer and are great for rooms with high ceilings, if you have extra wide windows with very heavy curtains or for just a sense of opulence in your home.
Do curtain poles have components?
Most manufacturers offer a standard amount of components with their curtain poles. This guide gives you a good idea of what is included but check the product details before purchasing.
Can you cut a curtain pole with a hacksaw?
Yes, all our standard metal curtain poles can all be cut down to your required size with a hacksaw. We suggest wrapping masking tape around the metal rods where you need to cut to help mark your cut on the shiny pole and it as protects your pole if you slip with the hacksaw.
Where are curtains located on a curtain pole?
The main set of curtains are usually located on the front pole , with nets or voiles fitted on the back pole. Great for privacy issues and will also camouflage an unattractive view while still allowing daylight into the room. Click here to view all Double Metal Curtain Poles. Eyelet and Tab Top Curtain Poles.
What is double curtain pole?
Double Curtain Poles. Double curtain poles may be purchased as sets, or made up using components from the "Create Your Own Curtain Pole" range. Double pole sets allow you to dress your windows with two pairs of curtains or voiles and curtains.
How to measure the height of a curtain pole?
If you already have your curtains, then to determine the height of the position of the curtain pole above the window (A) you will need to measure the drop of the curtains and add the measurement from the top inside of a curtain ring to the bottom outer edge for heading which will hang from the curtain rings.
How to measure for a short curtain?
For a short curtain use the drop length to measure from approx.12cms below the sill to mark the height (B) for the bracket location above the window recess, for curtains to sit on the sill measure from here instead, plus 0.5cm for clearance.
How to keep curtains from marking when hanging?
Cleaning the area with a vacuum cleaner as soon as you have fitted the brackets will keep your curtains from becoming marked when you hang them.
How to replace a pole?
To replace an existing pole with a new one, simply measure the total length of the existing pole excluding the finials. This will give you the total pole length you require to start shopping.
Why use a metal tape measure?
A metal tape measure is recommended for accuracy and ease of use.
Can you cut rails with a hacksaw?
Our rails and poles can be easity cut to any size with a small hack-saw. If you dont find the exact size you need, just order the one that is the next size up from your measurement.
Do pencil pleat curtains have fullness?
Remember to take into account any extra weight such as linings. Also note that pencil pleat curtains will have a greated fullness than a curtain with eyelets for example so the weight will also be greater.
How to cut metal with a hacksaw?
Hacksaw. Use a hacksaw with a metal-cutting blade. Use long, easy strokes and don't force the cut; let the blade do the work. Remember that a hacksaw only cuts on the forward stroke. The backward stroke is to reposition the blade for the next forward cutting stroke. Always sand the edges to remove sharpened burrs after cutting.
Can you cut a shower rod?
There are several ways to cut a metal shower rod, so choose the method that works for you, the tools you have and your abilities, and never cut the threaded end of a rod, if applicable.