Actually, there are many brands and products of LED light strips, so whether a light strip can still be used normally after being cut is not a question that can be given a general answer. It really depends on the specific product. In general, if the light strip has a cut line, it can be cut; if it has not, it is best not to cut it.
Can you cut LED light strips?
Take care when cutting LED light strips – make your cuts only at the designated points. If you cut somewhere other than the marked positions, you will likely disable some of the LED’s on the strip. The LED strip I purchased allowed cuts after every LED.
What is a commercial electric tape light kit?
This Commercial Electric tape light kit includes 4 x 12 in. linkable indoor soft white LED tape lights, power supply, mounting hardware and various connector wires. The LED's are extremely energy efficient, with the full 48 ft. using a mere 8.5 -Watt. Use the strips to add accent lighting to any space.
What to do if the LED light strip is too long?
If the LED light strip you bought is too long, you need to cut off the extra part. The first thing you should do is measure the right length. If you accidentally cut the strip too short, your effort will be wasted. Step 2. Look for the scissors logo on the light strip
What is the best tape for LED tape lighting?
Kichler TE Enhanced Series Aluminum extruded tape channels that are a step up, with most wide enough to accommodate multiple strips of LED Tape Lighting. The 30-degree angled channel doubles as a 60-degree channel when rotated for expanded installation options. This series will transform your lighting effect from task or accent to ambient.
How to test electrical connections on LED strip lights?
What do the black lines on the LED strip mean?
What is the first step in soldering LED lights?
How to connect a copper pad to a wire?
How to make sure wires don't short?
Can you cut LED strips every 3rd section?
Can you solder LED lights?
See 2 more
Can LED strip lights be cut and still work?
Will they continue to work if they are trimmed down? Yes, LED strip lights will carry on working after they've been cut as long as you cut along the designated lines. LED strips are made up of several individual circuits, so each cut line demarcates the end of one circuit and the start of a new one.
Can I cut LED tape lights?
LED Strip Lights are such a versatile product due to the fact that they can easily be cut on the given cut lines and connected at any point between the copper dots on the LED Strip Lights, cut lengths vary between products.
Can you cut LED lights without ruining them?
A: Some light strips can be cut to a specific length and continue to work. However, they must be cut according to the cut mark. There are some tiny and precise parts on LED light strips. If you accidentally cut the wrong place, you may cause the light to stop working normally.
Can LED strip lights be cut anywhere?
Can I Cut The LED Strip Light Anywhere Else? You can, but we wouldn't recommend it. By cutting an LED strip light anywhere other than the designated cutting point, you run the risk of damaging the components on the strip itself, as well as the circuit board. This may ultimately result in the strip light not working.
Can you cut LED strip lights to size?
LED Strip Lights are one of the most versatile types of lighting available and this is not just because they are flexible. They can also be cut to custom lengths, which means they can be potentially made to meet the requirements of any installation, no matter how big, or how small.
How do you use LED lights after cutting?
0:202:45How to Cut and Connect LED Light Strips. - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust make sure you line up the arrows. But a number of different occasions will call for you to cutMoreJust make sure you line up the arrows. But a number of different occasions will call for you to cut the wires. And either create new ends or solder extensions. So I'm going to show you how always cut
Can you cut Flexible LED strip lights?
Flexible LED strips are the universal choice for almost any accent lighting or task lighting application. One of the main advantages of flexible LED tape over rigid panels is the ability to cut these strips into custom lengths.
How do you connect two LED strips together?
0:543:44How To Connect Two LED Strips Together EASY ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust here you can chop off the little ND bit and then slot it into place spot the other one intoMoreJust here you can chop off the little ND bit and then slot it into place spot the other one into place. Job.
How do you shorten LED string lights?
The best way to shorten lights wired in series is to remove an entire series section of lights by cutting lights apart where there are only has two wires, with the lights unplugged. Then, simply cap each of the two cut wires with a wire connector.
What can I do with extra LED strips?
5:218:01Power Leftover LED Strips - No Soldering - 5v - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe last thing is you can just quickly plug it in with that same micro usb cord plugged into theMoreThe last thing is you can just quickly plug it in with that same micro usb cord plugged into the wall adapter or your usb on the computer. And make sure the lights turn on.
How do you fix ripped LED strips without soldering?
How to use a Tape to Tape connector This is the Tape to Tape connector for single colour LED Tape. ... Cut the LED Tape along the cut line with a pair of scissors. ... Now take your Tape to Tape connector and your 2 pieces of LED Tape that you are looking to join. Open the connector.More items...•
Can you cut string lights?
If you don't mind a little asymmetry, then don't sweat it! But if you do, you're probably wondering, “Can you cut string lights?” The short answer is: yes.
How to test electrical connections on LED strip lights?
Once you have both wires on this side soldered up, you can test your electrical connections by simply turning on the LED strip lights and seeing if both sides turn on.
What do the black lines on the LED strip mean?
The LED strip I purchased allowed cuts after every LED. The black lines in the middle of the copper pads indicate the designated cut points.
What is the first step in soldering LED lights?
When soldering LED strip lights, the first step is to remove the clear coating on top of the copper pads. I took a small paring knife and made a cut just inboard of the copper pads (close to the “-” and “+” symbols).
How to connect a copper pad to a wire?
With the first wire in place on the copper pad, add solder to the copper pad. Make sure your joint is strong, both mechanically and electrically. Also make sure that you do not add so much solder that it electrically connects one copper pad to the other.
How to make sure wires don't short?
Wrap up one wire with electrical tape to make sure that it can’t short with the other wire.
Can you cut LED strips every 3rd section?
The strip I was working with permitted a cut after every single LED section. Many LED strip lights can only be cut every third section or so. Chances are, an extra inch or half inch won’t make a tremendous difference in the final appearance of your lighting.
Can you solder LED lights?
Go ahead and gather your materials for soldering. Of course, you’ll need whatever wire you’ll be using to extend your LED light strip. I had some extra garage door safety sensor wire laying around. For the task of soldering LED strips, I thought this particular wire was perfect. It’s small gauge wire, but has a solid, rigid single conductor instead of stranded wire. This made it very easy to solder the wire to the small copper pads I’d just exposed on the cut ends of the LED light strips.
How to bend LED tape?
How to bend your LED tapes laterally with clip-on connectors. If your LED tape needs to bend at an angle greater than 45 degrees (for example, to go around a right-angle corner), then we do not recommend physically bending it. Instead, we suggest one of our tape connectors. Clip-on connectors have a standard 150mm cable.
What does it mean to bend LED tapes laterally?
When we talk about ‘bending LED tapes laterally’, it means creating a curve of light on a flat surface (by bending the strip across the edge of the PCB). Like this:
How long is a clip on connector?
Clip-on connectors have a standard 150mm cable. This length cannot be adjusted, so you’ll have to find space to hide any excess cable. This can be a problem for some installations.
Why are LED strips less flexible than lower power LED strips?
This is because the LED modules are placed closer together on high-power strips, and require wider PCBs (for more heat dispersal).
Can you order flexible LED tape?
You can order your tape with flexible LED strip connectors already fitted. Tell us where you want your tape to bend, and we’ll cut and solder your flexible connector (s) before your order is dispatched – so it’s ready to use right out of the package.
Can you cut LED lights without cable?
Link cables are completely customisable, so they can be cut to fit your LED strip lighting project exactly – without excess cable, or with longer cables if required.
Does InStyle have LED tape?
InStyle ’s LED tape offers you more flexibility than other forms of lighting. You can fit it to curved surfaces, twist it and even loop it back on itself. (After all, it’s supplied on reels!)
What happens if you cut a Lepro LED light?
If you accidentally cut the wrong place, you may cause the light to stop working normally. After cutting the light strip, you can place the required parts in the proper position and turn on the lights by following to these steps. The following steps use Lepro LED light strips as an example: Step 1.
What happens if you cut LED lights diagonally?
If you accidentally cut diagonally, it may cause a light to stop working, so make sure you cut straight. Part 2. How to Fix LED Strip Lights When Cut. Q: I purchased a LED strip lights and used a portion of it, but I also want to use the remaining portion.
What size connector for a 10mm light strip?
If your light strip is 10mm wide, the 4Pin connector you select must be suitable for 10mm. If your light strip is 8mm wide and you purchase a 10mm connector, it will not work. Step 2. Open the connector. If the connector has a cover, you have to open the connector on the side. Step 3.
How to connect LED light strip to connector?
Place the two cut ends of the LED light strip into the fastening clips of the connector. At this point, you should check that they are not reversed by following the picture instruction.
How to check if light strip is lit?
After placing the light strip, close the cover of the connector and try to see if the light strip is lit normally after the power supply is connected. If the connected parts do not light up normally, try adjusting the connecting point between the connector and the light strip.
What to do if LED light is too long?
If the LED light strip you bought is too long, you need to cut off the extra part. The first thing you should do is measure the right length. If you accidentally cut the strip too short, your effort will be wasted. Step 2. Look for the scissors logo on the light strip.
What does it mean when an LED light is not lit?
After performing the above steps, if you find that the LED light strip is still not lit, check that there is no connection issue. If the set-up is normal, it means the light strip may have been damaged during the cutting process, so be careful and always cut according to the logo on the strip.
How to test electrical connections on LED strip lights?
Once you have both wires on this side soldered up, you can test your electrical connections by simply turning on the LED strip lights and seeing if both sides turn on.
What do the black lines on the LED strip mean?
The LED strip I purchased allowed cuts after every LED. The black lines in the middle of the copper pads indicate the designated cut points.
What is the first step in soldering LED lights?
When soldering LED strip lights, the first step is to remove the clear coating on top of the copper pads. I took a small paring knife and made a cut just inboard of the copper pads (close to the “-” and “+” symbols).
How to connect a copper pad to a wire?
With the first wire in place on the copper pad, add solder to the copper pad. Make sure your joint is strong, both mechanically and electrically. Also make sure that you do not add so much solder that it electrically connects one copper pad to the other.
How to make sure wires don't short?
Wrap up one wire with electrical tape to make sure that it can’t short with the other wire.
Can you cut LED strips every 3rd section?
The strip I was working with permitted a cut after every single LED section. Many LED strip lights can only be cut every third section or so. Chances are, an extra inch or half inch won’t make a tremendous difference in the final appearance of your lighting.
Can you solder LED lights?
Go ahead and gather your materials for soldering. Of course, you’ll need whatever wire you’ll be using to extend your LED light strip. I had some extra garage door safety sensor wire laying around. For the task of soldering LED strips, I thought this particular wire was perfect. It’s small gauge wire, but has a solid, rigid single conductor instead of stranded wire. This made it very easy to solder the wire to the small copper pads I’d just exposed on the cut ends of the LED light strips.
