ThoroSeal Waterproof Coating ® and ThoroSeal Foundation Coating ® should never be painted over. ThoroSeal ® Waterproofing Paint may be painted over, but wait at least 30 days to allow a full and complete cure, and then use latex paint only.
Can thoroseal be used on both the interior and exterior walls?
There is a Thoroseal product for use on both the exterior and interior of foundation walls. It's called "Thoroseal". Just that. The stuff in the bags is "Thoroseal Foundation Coating". That stuff is designed only for exterior use ("Waterproof, cement-based coating for exterior below grade concrete and masonry").
How much thoroseal do I mix with acryl-60?
Thoroseal PDF file You'll need a minimum of 1.5 quarts of Acryl-60 per 50 lb. bag of Thoroseal. You mix the Acryl-60 with an additional three parts water, so 1.5 quarts of Acryl-60 gives you 6 quarts of liquid to mix with the 50 lb. bag.
What is thoroseal foundation coating?
It's called "Thoroseal". Just that. The stuff in the bags is "Thoroseal Foundation Coating". That stuff is designed only for exterior use ("Waterproof, cement-based coating for exterior below grade concrete and masonry"). If you download this PDF file (you'll need the free Acrobat Reader software) you can read all about Thoroseal.
How do you apply thoroseal coating?
Use a tampico fiber brush to apply the Thoroseal to the desired surface. Thoroughly brush the Thoroseal over the entire surface and make sure the surface is covered evenly. Aim for 2 lbs. of Thoroseal mixture for every square yard of the surface. Finish the coating with smooth horizontal strokes over the entire surface.
Can you paint over waterproofing paint?
Can you paint over DRYLOK® Masonry Waterproofer? A. Absolutely. In fact, DRYLOK® makes an ideal base coat.
Can you paint over MasterSeal?
Yes, if your MasterSeal NP1 Sealant is completely cured and clean, it can be painted with elastomeric paint. Keep in mind not to use any oil-based caulking, sealants, or other products with asphalt, tar, or oil when using NP1 – this is very important.
Can you paint over concrete waterproofing?
Bottom line: If you wish to paint a line on concrete that has been treated with a sealer or coating, the sealer or coating must be removed before the paint is applied. To accomplish this, the concrete should be stripped to a level below that to which the sealer or coating has penetrated.
Is Thoroseal a paint?
It's a low-gloss paint that's a good choice for medium- or low-traffic areas, and it does a better job of disguising imperfections than satin-finish paint. Q: Can I paint without primer? A: It's best to use a primer prior to painting. Primer helps the ThoroSeal paint stick better to the wall.
How long does it take Thoroseal to cure?
Allow Thoroseal® Foundation Coating to cure 7 – 10 days before immersion in water.
What type of waterproofing is Thoroseal?
cement based waterproofingMasterSeal 581 (formerly Thoroseal) is for concrete and masonry and resists both positive and negative hydrostatic pressure. It is a cement based waterproofing for Interior and Exterior, above and below grade, with a high quality finish suitable for architectural coatings, and is NSF 61 Potable Water Certified.
Can MasterSeal NP 1 be painted?
NP-1TM requires no mixing and typically bonds to many materials without a primer, including concrete and masonry. NP1 dries with a smooth finish and is paintable.
Is MasterSeal NP 150 paintable?
Service temperature range: -40 to 220° F. Expected service life: Up to 25 years. Shrinkage: None. Paintable: Yes.
Will paint stick to concrete sealer?
Most concrete sealers bond to the concrete by filling and gripping the pores, making it almost impossible for paint to adhere properly. These sealers need to be removed or the concrete surface roughened by sanding, grinding, or etching. However, some water-based sealers will allow paint to bond.
Can you paint over waterproof sealer?
Paint can be applied to water sealers, but the drying time of the sealer itself is the most important part of this task. For best results, prime the water-sealed wood first. Use either a latex-based or an oil-based primer as your first coat of paint before applying the finishing coat.
Does paint stick to sealer?
Keeping this in mind, can you paint over wood sealer? Painting over sealed wood will result in bubbling, flaking, or chipping. Because sealants are created to seal out moisture and create a protective coat, the paint will not adhere to sealed wood materials.
What is Thoroseal used for?
Thoroseal® 550i is a ready-to-use polymer-modified cement-based coating. It is used to waterproof and protect concrete, mortar, and masonry surfaces requiring either positive- or negative-side waterproofing. Thoroseal® 550i can be applied by low-pressure spraying or hand troweling.
Is Thoroseal still made?
This Product is manufactured in United States.
Does Thoroseal come in colors?
Coverage will vary depending on surface texture and porosity. White and standard gray (this color is not uniform) Custom and landscape colors are available for 5,000 lbs (2,268 kg) minimum order.
What is super Thoroseal?
Super Thoroseal is a blend of Portland cements, selected aggregates and spray dried polymer modifying agents. The aggregates are carefully graded. When mixed with clean water to a slurry consistency, Super Thoroseal can be applied easily with a stiff hand brush, broom or spray equipment.
Is Thoroseal cementitious?
Super Thoroseal is a cementitious waterproofing best.
Is Thoroseal safe for drinking water?
It is also used in culvert tanks to seal the seam between the metal culvert and concrete base (after the concrete has been sealed with Thoroseal), and the spiraling seam of the culvert itself. It is USDA-approved and NSF-approved for potable water contact.
Who owns Thoroseal?
Thoro concrete and waterproofing products now a part of Master Builders Solutions.
How do you mix Thoroseal waterproofing?
2:345:23BASF Thoroseal - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater approximately five point two liters is necessary for a twenty five kilo sack of thoraseal.MoreWater approximately five point two liters is necessary for a twenty five kilo sack of thoraseal. Powder. Add the powder to the liquid and mix to a lump-free consistency. Let the mixture rest for a few
How much Thoroseal do I need?
Mix Thoroseal® Foundation Coating with a mixing liquid consisting of a blend of Acryl 60® diluted with water. Maximum dilution ratio is 1 part Acryl 60® to 3 parts water. Approximately 6 quarts (5.7 L) of mixing liquid is needed per 50 lbs (22.7 kg) of Thoroseal® powder.
What flex seal product can you paint over?
When we created the Flex Seal Family of Products, we never imagined how many different ways our customers would use them. One of the most common questions we receive is “Can I paint over Flex Seal?” Flex Seal Spray and Flex Glue can be painted over. Flex Seal Liquid and Flex Shot can not be painted over.
Can you paint over waterproofing sealant?
Can I paint over Water Seal? No. The hydrophobic properties of Water Seal will negatively affect the adhesion of any paint applied over it.
Does paint stick to Flex Seal?
If you are using the Flex Glue, or the Flex Seal Spray you can apply paint over them. On the other hand, if you are using Flex Shot or Flex Seal Liquid, you cannot apply paint over them.
What sealants can you paint over?
The benefit of colour-matching using a non-silicone sealant comes if you need to paint over it (such as spray-painting the side of a bus). A non-silicone sealant will not repel the paint meaning it will not flake off and crack.
How to apply tampico fiber?
Use a tampico fiber brush to apply the Thoroseal to the desired surface. Thoroughly brush the Thoroseal over the entire surface and make sure the surface is covered evenly. Aim for 2 lbs. of Thoroseal mixture for every square yard of the surface.
What is a tampico fiber brush?
Thoroseal is a building product manufactured by BASF Construction Chemicals. It is a waterproof cement-based coating that is used to fill, seal and protect interior and exterior surfaces.
How to mix thoroseal with water?
Use a bucket and a power mixer fitted with a mixing paddle to mix the Thoroseal with water. Thoroseal can be mixed by hand, but using a power mixer is more effective. Mix the Thoroseal with water at a ratio of 6 to 8 quarts of water for a 50-lb. bag of Thoroseal.
How to use thoroseal?
Fill up the container of your high-pressure water spray with water. Use the spray to blast all the dirt, dust and other contaminants from the surface to which Thoroseal will be applied. Make sure the surface is completely clean before you apply Thoroseal.
How long does it take for a paint coat to cure?
Finish the coating with smooth horizontal strokes over the entire surface. Leave the coating for 24 hours to cure before applying the second coat.
What is Thoroseal used for?
It is resistant against weather erosion and can be used to protect concrete, brick, building blocks and other materials. The application of Thoroseal is carried out in a similar way to painting. Advertisement.
Where is Jack Taylor?
He holds a Bachelor of Arts in journalism from University College, Falmouth.
Why is my wall damp?
Moisture issues are actually related to the ability of coatings to handle water pressure. If your wall can’t handle moisture well, it’ll cause dampness in the building.
How long does it take for drylok to dry?
Drylok takes a lot less time to dry after applying a full coat. You’ll see that after two full coatings, Drylok takes around 9-10 hours in total. For Thoroseal, you’d need to spare around 24-48 hours.
How many square feet does Thoroseal cover?
Thoroseal covers 105 square feet per gallon. And Drylok provides a coverage of 75-100 square feet per gallon. Thus, you can see that Thoroseal is more suitable for larger projects.
Which is better, Drylok or Thoroseal?
First, in terms of the quality of coatings, Thoroseal is a better choice. However, Drylok is simpler to apply. Also, Drylok has a greater vapor permeability. On the other hand, Thoroseal is more resistant to absorbing moisture.
Is Thoroseal hard or soft?
Thoroseal surpasses Drylok in terms of quality. The coating provided by Thoroseal is extremely firm and hard. This makes Thoroseal more durable too. Because the walls would be prone to receiving more damage there.
Is drylok the same as thoroseal?
By definition, Thoroseal is a cement-based coating made of latex. On the other hand, Drylok is a paint made of latex and oil with a sealant’s properties. So, you can say that they’re different substances serving the same purpose.
Can you cover a damaged concrete wall with pictures?
The use of these coatings can serve various needs of your walls. So, you don’t need to cover the damaged parts of your concrete wall by hanging pictures! They will fix your wall perfectly. But the question is, which one would do a better job?
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping. Register today
Have a question?
Your question might be answered by sellers, manufacturers, or customers who bought this product.
Product Description
MasterSeal 583 Formerly Super Thoroseal Waterproof Coating Not a paint, a heavy, cement base waterproof coating for concrete or masonry Harder than the wall itself Fills and seals pores and voids, assures complete protection against water penetration Dry powder form, just add water White 5 gallons. This Product is manufactured in United States.
