Can you solder with acetylene? Because soldering alloys all melt at temperatures much below 4270C, to use an oxy- acetylene flame for a soldering operation is not only pointless, but difficult, since that flame is so hot that overheating of the metal is hard to avoid. Most widely used are air-acetylene and air-propane torches.
What kind of fuel do you use to solder electrical wire?
Can you solder with acetylene? Because soldering alloys all melt at temperatures much below 4270C, to use an oxy- acetylene flame for a soldering operation is not only pointless, but difficult, since that flame is so hot that overheating of the metal is hard to avoid. Most widely used are air-acetylene and air-propane torches.
Can You silver solder with a propane torch?
Jun 18, 2009 · The thing about soldering plumbing with oxy-acetylene is, the flame is really far too hot for the job. If you move the flame all or mostly around the joint to heat evenly, no problem. But sometimes your access isn't very good. With propane, the rate of …
What is the best heat for soldering?
The acetylene flame should be about 2-3 times the size of the oxygen flame. You will also need to use a flux to help the solder flow properly. Put some flux on the copper and then put the solder on top. Hold the torch so that the flames are touching the copper and solder. Move the torch around so that the solder melts and
Can I silver solder with MAPP gas?
Dec 11, 2021 · You can use the oxy-acetylene tank to solder different metals depending on the thickness of the welding rod. You can use the tank to weld aluminum metal. You can use the tank to weld aluminum metal. Also, you can weld other metals such as stainless steel, even if it is difficult to cut the metal unless you use high heat and pressure.
Would you use propane or acetylene for soldering?
Acetylene burns over 1000°F hotter than propane! Note that oxy acetylene combinations burn significantly hotter (5612°F) and should not be used for soldering copper as this is above coppers melting temperature (1984°F).Jan 10, 2018
How do you solder copper pipe with acetylene?
2:0810:07How To Silver Solder (Braze) a Copper Pipe (A/C Line Repair)YouTubeStart of suggested clipEnd of suggested clipAnd finally the torch when soldering a torch like this is used seeing only one type of gas is neededMoreAnd finally the torch when soldering a torch like this is used seeing only one type of gas is needed Plus propane torches don't give out near as much heat as the following the oxy acetylene torch.
Can you solder copper with acetylene?
Soldering to join copper pipes may be done with an air acetylene, air Mapp, or air propane torch. Oxyacetylene is not recommended for soldering because its flame temperature is so high that it is easy to overheat the pipe and burn the solder or flux so that no bonding can occur.Mar 6, 2006
Can you solder with a welding torch?
Torch Welding Can Be Done Even though lower-temperature blowtorches are better suited for brazing and soldering than actual welding, blowtorches that run on hotter fuel-air mixtures such as oxyacetylene can hold their own against more complicated welding techniques.
Is silver solder stronger than brazing?
Soldering, in addition to having a lower processing temperature, typically results in a lower-strength joint than a brazed joint. For many applications, this is suitable and even desirable. The shear strength of brazed joints typically exceeds that of soldered joints by a factor of five.Feb 20, 2014
What gas do plumbers use for soldering?
MAPP gasUse MAPP gas to speed up the job MAPP gas torches burn hotter than propane, making them a better choice for modern solder. Five to 10 seconds of heating with a MAPP gas torch is all that's required before you can feed solder into most 1/2- to 3/4-in. pipes and fittings.Nov 25, 2019
Can you silver solder with acetylene?
Use a long life flux. Use the oxy-acetylene only at the end to finally lift the joint temperature for silver soldering. Regretably your experience is not uncommon when oxy-acetylene is used. Finally - ensure that any future work is done in a well ventilated area.Oct 7, 2012
Can you use oxygen to solder?
FUEL GASES Heating jewelry pieces during soldering is done with torches, which mix either oxygen or air with a gas. Hydrogen, natural gas, acetylene, propane, and butane are the fuel gases most commonly used.Apr 25, 2019
Will a torch cut copper?
Oxy-fuel cutting cannot cut non-ferrous metals such as aluminum, stainless, brass or copper.
Can you silver solder with a butane torch?
An ordinary household propane or butane torch will work, but even better is one of the new torches that burn MAPP gas. Most hardware stores have them. They burn much hotter than ordinary torches, which makes silver soldering go faster and easier. Use silver solder like ordinary solder.Jan 27, 1978
Does solder stick to steel?
Although steel is usually welded or brazed together, you can also solder it. Soldering steel wire is not unlike soldering other wire types like silver or copper.
How do you solder metal with a torch?
0:014:15How to Silver Solder Steel with a Propane Torch and SSF-6 High ...YouTubeStart of suggested clipEnd of suggested clipWe're going to use the SSF six it's as strong as a MIG weld or TIG. Well I'm just using a propaneMoreWe're going to use the SSF six it's as strong as a MIG weld or TIG. Well I'm just using a propane torch. If you get into heavier pieces of steel of course use oxy acetylene.