Do Yorkshire Fittings need flux? There are two types of fitting to make a soldered pipe joint, one which comes with a ring of solder already inside each end of the fitting, called a Yorkshire fitting, and the other, an end feed fitting. You will then need to apply a liberal amount of flux to both the pipe and the fitting.
Full Answer
Do Plumbers use Yorkshire fittings (ring solder joints)?
I'm not a plumber by trade but came into plumbing through the handyman route. I have worked with a plumber on my own house and he taught me to use Yorkshire fittings (ring solder joints). One tip he taught me was to apply some extra solder to the joint when you solder it in a similar way as you would for an end feed joint.
Do you use Yorkshire fittings when refitting a bathroom?
Am refitting my own bathroom, using yorkshire fittings for where possible, however this means that I have to solder all the joints on each piece in one go (else the fitting heats up and melts the solder on tother part).
How to use flux correctly when soldering?
Also consider continually dipping the end of solder wire in the flux, as this will add flux keeping joint clean and the melting wire solder gives indication of when the fitting is at correct temperature I was soldering some 15mm Yorkshire fittings today.
Can I use endend feed for 28mm fittings?
End feed is fine for 15 and 22mm. It takes some skill to get a good flow of solder around a 28mm fitting especially if you are working in cramped conditions. I sometimes use pre-soldered fittings with these joints (though they are veeeery expensive)!
Do you need to flux Yorkshire Fittings?
Yorkshire joints The joint can then be heated and lead-free solder end-fed. If a new tube is to be used, clean and flux the tube before assembly. End feed lead-free solder at the mouth of the socket after reheating.
Do you need flux on pre soldered fittings?
You must always remember to use flux to help the solder to run around the joint in a capillary action. This will ensure a tight, even and watertight pipe join. This will also prevent oxidisation.
Can you solder a Yorkshire fitting?
The application of solder is still a good idea with Yorkshire fittings to be absolutely sure of a good joint. Make sure you have a damp rag handy, and after a few seconds, to allow the solder to set, carefully wipe the joint round. This will cool it and clean it.
How do you use Yorkshire solder ring fittings?
3:556:04How to use Solder ring fittings | Yorkshire fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also apply some flock to the inside of the fitting if you wish to do. So. You don't takeMoreYou can also apply some flock to the inside of the fitting if you wish to do. So. You don't take both pieces of pipe. And show that they are pushed fully into the fitting.
Can you use Yorkshire Fittings on gas?
Yorkshire Flux, like Traditional Craftsman's, will maintain it's consistency and can be used with all types and sizes of soft solder fittings. However, it must not be used for gas applications.
How do you install pre soldered copper fittings?
0:541:43Copper Fittings with Solder - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the sandpaper to clean the end of the copper pipe and then take the flux that you normally useMoreUse the sandpaper to clean the end of the copper pipe and then take the flux that you normally use spread it on both ends. Put the fitting on the pipe. Turn on the torch. Heat.
How do you solder a Microbore pipe?
3:246:00Soldering copper pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipPipes. And when you've done that you can then insert your fitting. So we're just going to push thatMorePipes. And when you've done that you can then insert your fitting. So we're just going to push that into there. And we're going to push both ends until the up all the way on.
What is plumbers flux?
In plumbing, flux is a compound used as part of soldering a pipe joint. It's an acidic paste that is applied to the part of the copper pipe where the solder must make a bond. It cleans the joint, if you rub it on some copper and leave it a short while, it will be left gleaming when you wipe it off.
What is flux in soldering?
What is Flux? Flux aids in soldering and desoldering processes by removing oxide films which form on the surface of metals being soldered. It increases the wetting ability of the solder, causing it to flow more uniformly over surfaces without balling-up (dewetting).
What are Yorkshire pipe fittings?
Yorkshire fittings are pre-soldered connectors used to join pipework for water, oil and gas systems and are not demountable. Attractive when visible and ideal for confined spaces. Yorkshire pipe fittings are manufactured in the UK, ideal in hard or soft water areas and are suitable for use on drinking water supplies.
What is the best way to solder copper pipes?
3:395:05How to Solder Copper Pipe The CORRECT Way | GOT2LEARNYouTubeStart of suggested clipEnd of suggested clipSo always start from the bottom. And work your way up and reason too is as you heat the bottom theMoreSo always start from the bottom. And work your way up and reason too is as you heat the bottom the heat rises.
How do you know if your solder joints are good?
A good solder joint should have an even band of solder showing all the way around. If you see an area that looks as if it needs more solder, brush a little flux onto the joint. If the joint is still warm, the flux will melt and flow into the void. Then reheat the joint and resolder.
jgw1 New Member
Cheers hotdog, I am a bit worried now that I have over heated them. If I do then does that stop it working?
doing a bit New Member
i find it easier to use end feed than pre soldered fittings any way, when doing a joint then apply the heat to one side of the fiting and the solder on the far side, when the solder runs on the opposite side the whole fitting is hot enough.
freud12 New Member
End feed is fine for 15 and 22mm. It takes some skill to get a good flow of solder around a 28mm fitting especially if you are working in cramped conditions. I sometimes use pre-soldered fittings with these joints (though they are veeeery expensive)!
jgw1 New Member
Following on from this, if a joint has dodgy soldering from overheating does it tend to leak right from the go or pop some way down the line?
tightenit New Member
Rule one is that all pipework to be soldered is dry.
freud12 New Member
If the joints look black and sooty after you've soldered, this can be a sign of over-heating - although you may be lucky.
freud12 New Member
Oh, I forgot to add that I find a small hand mirror useful to see if the solder ring has formed on the back side of the joint. Inspection type mirrors (on telescopic handles) are now available to make this easier (you should be able to pick-up a cheap one of these on a tool market stall).