How are clock inserts measured? The overall diameter is measured from the outside edge of the bezel to the other edge of the bezel. The mounting diameter is the diameter of the opening that the insert will press into.
How do you measure a clock insert?
How to measure clock inserts. Industry standard for clock inserts movements is the outside dimension of the bezel rim of clock face. The insert alone will be too loose of a fit so there is a rubber ring on the back side to fill the gap. Friction fit clock inserts fit into an existing hole.
Do you carry all sizes of clock inserts?
No we don't. We carry about 150 clock inserts in sizes from 1-7/16" up to 6" outside diameter. The sizes available are listed on our Clock Inserts home page .
What if the hole size is too small on my Clock insert?
Often you can build up the back of your clock insert with something like black electricians tape or some plumbers tape. So if the clock insert says it fits a 3-inch hole size, you can add material so it more snugly fits in a 3-1/4" hole size. What if the hole size is too small? What can I do? That will depend on the material you are working with.
How do you put a clock in a hole?
In other words, drill a hole into any object and just push the clock insert into it. The insert alone will be too loose of a fit so there is a rubber ring on the back side to fill the gap. Sometimes the rings will break or get lost and a simple solution is a rubber band.
What size hole do you put on a clock insert?
What does the length of a clock hand determine?
What is included in a high torque movement?
Can you remove material to increase hole size?
Can you add videos to your watch history?
Can you buy a black end cap separately?
Is the measurement information the only information that helps us?
See 2 more
How do you measure a clock hand replacement?
0:312:35How to Select Clock Hands for Your Clock Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll starts with a tape measure or ruler and measuring the diameter of the clock face or clock dialMoreAll starts with a tape measure or ruler and measuring the diameter of the clock face or clock dial take a look at this clock dial.
How do you measure clock parts?
0:063:46Get The Right Clock Motor - Two Measurements - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe hand shaft is the length of your minute hand that's how you measure clock hands from theMoreThe hand shaft is the length of your minute hand that's how you measure clock hands from the mounting hole of the minute hand to the tip in this case it's under 5 inches therefore.
How is clock movement shaft length measured?
0:552:24How to Determine the Correct Clock Motor Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipCalled the overall length where you measure from the top of the shaft all the way to the bottom ofMoreCalled the overall length where you measure from the top of the shaft all the way to the bottom of the threading. The overall shaft length is important because if you have any type of glass lens.
How do I choose a replacement clock mechanism?
0:003:01How to Select the Correct Clock Movement - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust make sure that the threaded part of the hand shaft is 1/16 to 1/8 of an inch longer than theMoreJust make sure that the threaded part of the hand shaft is 1/16 to 1/8 of an inch longer than the thickness of the clock face.
Are clock hands universal?
Remember clock hands are not always interchangeable. It is advisable to purchase new high torque hands at the same time.
Are clock hands interchangeable?
At 12 o'clock, the hour hand and minute hand of the clock can be swapped, and the clock still gives the same time, but at 6 o'clock, it can not be swapped.
What is the shaft length on a clock?
The overall length is measured from the tip of the hand shaft to the case of the movement (B). Allow an additional 1/8” for cap nut or sweep second hand. The threaded portion of the hand shaft (A) is the part of the shaft which will secure your movement to the dial plate or wood.
How do you measure a clock movement kit?
The post mounting hole of your clock dial (or mounting material) needs to have a large enough diameter to fit the shaft of the clock movement through it. The easiest and most accurate way to measure the shaft length on a clock movement is to use the depth gauge on a digital caliper.
What is the spindle length on a clock?
The movement with the shorter 14mm spindle is designed to go through clock faces upto 4mm thick, whereas the 23mm spindle is designed to go through clock faces 10mm to 12.5mm thick. However, the long spindle version can be used for clock face thicknesses of 4mm to 10mm thick by using a packing piece or thick washer.
What is a clock dial thickness?
Dial thickness is the measurement of the material that the shaft of the clock motor is going through. Example you have a piece of material which is 8mm thick you would simply choose a 10mm dial thickness size as the 6mm dial thickness would be to small and the 10mm is suitable for sizes up to 10mm.
How do you measure a clock key?
On the back of your clock is the winding arbor (the steel shaft the key fits on to). With your digital gauge, measure the square shaft from flat side to flat side to get the millimeter size. Most winding arbors taper out towards the the clock and the end section is most likely the smallest.
What does high torque clock movement mean?
High Torque Clock Motors are more powerful - made specifically to handle the extra weight of longer clock hands up to 18" in length. This means you can make a clock with a clock face/dial that is 42" wide or even greater! Comparatively, standard movements run clock hands up to 4.5 inches long.
What is the spindle length on a clock?
The movement with the shorter 14mm spindle is designed to go through clock faces upto 4mm thick, whereas the 23mm spindle is designed to go through clock faces 10mm to 12.5mm thick. However, the long spindle version can be used for clock face thicknesses of 4mm to 10mm thick by using a packing piece or thick washer.
How do I know what size my clock key is?
On the back of your clock is the winding arbor (the steel shaft the key fits on to). With your digital gauge, measure the square shaft from flat side to flat side to get the millimeter size. Most winding arbors taper out towards the the clock and the end section is most likely the smallest.
What is the diameter of a clock?
12 inch clocks are 12 inches diameter, 18 are 18 inches diameter, 24 clocks are 24 inches diameter etc! Make sure to get a battery that is over 1.3v for the large wall clocks. The larger hands take a lot of energy so a better battery will last longer. Lithium batteries are said to last a long time in clocks.
What is dial thickness on a clock?
Dial thickness is the measurement of the material that the shaft of the clock motor is going through. Example you have a piece of material which is 8mm thick you would simply choose a 10mm dial thickness size as the 6mm dial thickness would be to small and the 10mm is suitable for sizes up to 10mm.
What does mounting diameter mean?
The size of the hole in the clock housing that the insert will fit into.
What is a clock insert?
An insert is an encapsulated timepiece that is inserted into a predrilled hole.
How are clock inserts measured?
The overall diameter is measured from the outside edge of the bezel to the other edge of the bezel. The mounting diameter is the diameter of the op...
What size hole do you put on a clock insert?
So if the clock insert says it fits a 3-inch hole size, you can add material so it more snugly fits in a 3-1/4" hole size.
What does the length of a clock hand determine?
The length of your clock hands determines whether you need a standard clock motor or high torque (higher power) clock motor.
What is included in a high torque movement?
High Torque Movements include an End Cap in brass color. You can purchase a black end cap separately. You can also purchase an open-end nut separately.
Can you remove material to increase hole size?
That will depend on the material you are working with. Sometimes our customers will remove a bit of material to increase the hole size to fit.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Can you buy a black end cap separately?
Standard (AKA Mini) movements include a hanging bracket, mounting nut, washer, and an open second-hand nut. You can purchase a black or brass end cap separately if you are not going to use a second hand.
Is the measurement information the only information that helps us?
Sadly, no. The only information that helps us is the measurements.
How to choose a clock insert?
1) Browse a variety of clock faces and styles and bezel color within each size option. 2) Plus Picture Frame Inserts, Thermometers and Barometers available in a few sizes. 3) Mix and Match for Better Quantity Pricing (Within Each Size, up to 3-1/2") How to Choose Clock Inserts / Fitups.
What is a clock insert?
Clock inserts for replacements repairs and new clocks are quick and simple to use. With the inner clock mechanisms of a wristwatch, clock fit-ups are all you need to add a sophisticated and quality clock component to your project. Each year we supply tens of thousands of high quality clock inserts as replacement parts and to complete new clock projects
How to fit a friction fit clock?
Friction fit clock inserts fit into an existing hole. In other words, drill a hole into any object and just push the clock insert into it. The insert alone will be too loose of a fit so there is a rubber ring on the back side to fill the gap. Sometimes the rings will break or get lost and a simple solution is a rubber band. Slide a rubber band on the backside of the insert and we are good to go! It ends up being a nice fit with some tolerance in the hole diameter requirement.
Can a friction fit clock be scratched?
The plastic can scratch. Be careful when cleaning the face of the clock. If it does get a scratch, get a new insert. Replacement lenses for friction fit clock insert are not available . In fact, sometimes when the bezel is taken off, it will not go back on.
What size hole do you put on a clock insert?
So if the clock insert says it fits a 3-inch hole size, you can add material so it more snugly fits in a 3-1/4" hole size.
What does the length of a clock hand determine?
The length of your clock hands determines whether you need a standard clock motor or high torque (higher power) clock motor.
What is included in a high torque movement?
High Torque Movements include an End Cap in brass color. You can purchase a black end cap separately. You can also purchase an open-end nut separately.
Can you remove material to increase hole size?
That will depend on the material you are working with. Sometimes our customers will remove a bit of material to increase the hole size to fit.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
Can you buy a black end cap separately?
Standard (AKA Mini) movements include a hanging bracket, mounting nut, washer, and an open second-hand nut. You can purchase a black or brass end cap separately if you are not going to use a second hand.
Is the measurement information the only information that helps us?
Sadly, no. The only information that helps us is the measurements.