Steps
- Prepare your cabinets. Remove the cabinet doors, as well as the hinges, knobs and other fixtures. ...
- Choose a process for antiquing white cabinets. Glazing involves applying a thinned paint mixture, called a glaze, over the cabinet surfaces in order to create antique white cabinets.
- Glaze your cabinets. ...
- Distress your cabinets. ...
- Apply a crackle finish. ...
How do you glaze antique cabinet doors?
Brush glaze onto door by going in the director of the wood grain. TIP: Use a rag to wipe off portions of the applied stain; this will result in discolorations that will help the wood look worn not too dark and “fake”. Add more antique glaze to the edges of your cabinet doors.
How do you stain antique kitchen cabinet doors?
But mostly, you can just go ahead, pick up a sponge, dip it in the stain and carefully apply the antique stain on the sides and corners to give your kitchen cabinet that final touch of vintage charm. There are two ways to apply glaze to a cabinet door.
How do you repair an antique door?
The most common repair that needs to be done on antique doors is usually patching old hinge gains and latch holes with a wood Dutchman. Here’s the easiest step-by-step process: Remove paint from the area you need to repair so that you’re dealing with only bare wood.
How do you antique white cabinets?
Antiquing white cabinets with the glaze method is a process, and you may need to build layer upon layer before you are satisfied with the level of antiquing. For greater detail and dimension, use a small paint brush to layer extra glaze into cracks, crevices and joint lines, where dust would naturally settle.
How do you apply antique glaze to cabinets?
Add a small amount of antiquing glaze to a smooth, clean rag. Begin applying the glaze to the front or side of one cabinet in small, circular motions until you've covered the entire section. Tip: A small amount of glaze will go a very long way. It's better to start with too little glaze rather than too much.
How do I make kitchen cabinets look distressed?
Distressed Kitchen Cabinets: How To Distress Your Kitchen...Remove all of the cabinet hardware.Sand the cabinets with a sanding block. ... When all of the sanding is done, clean clean clean. ... Bust out the antiquing glaze. ... Apply a top coat. ... Let the topcoat dry for about 24 hours before you add your hardware.
How do you patina cabinets?
1:104:31Dixie Belle Patina Paint- Radio Cabinet Furniture MakeoverYouTubeStart of suggested clipEnd of suggested clipFor the next color in the ombre i mix a tablespoon of drop cloth into a tablespoon of the vintageMoreFor the next color in the ombre i mix a tablespoon of drop cloth into a tablespoon of the vintage duck egg. So i'm getting a lighter version of the color that i started with on the bottom. So for the
Can you antique stained cabinets?
If your cabinets are stained, you've already taken the first step toward creating antique charm. To complete the procedure, you can apply a glaze, distress the wood or do both. It's best to distress before you glaze, because the glaze settles into the nicks and gouges and highlights them.
How do you make new cabinets look old?
1:113:52How to Give Your Kitchen Cabinets an Antique Look - YouTubeYouTubeStart of suggested clipEnd of suggested clipTogether simply brush the glaze on filling every nook and cranny keep in mind that the place driesMoreTogether simply brush the glaze on filling every nook and cranny keep in mind that the place dries quite quickly.
What is antiquing glaze?
Antiquing is the technique of glazing a base finish to simulate age or create an interesting color effect. Enamel is the most common base for antiquing, but varnished, shellacked, and lacquered surfaces can also be glazed.
How do you make wood look like a patina?
0:407:11How to make Wood Rust - Amazing Patina Paint Ideas - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo first thing you're gonna want to do is use any color of dixiebell paint. First onto the pieceMoreSo first thing you're gonna want to do is use any color of dixiebell paint. First onto the piece that you're planning on patina.
How do you paint wood to look patina?
0:312:20how to paint furniture. ditressed, aged looking patina. - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore painting furniture it needs to be properly prepped which means sanding it thoroughly andMoreBefore painting furniture it needs to be properly prepped which means sanding it thoroughly and cleaning it well I'm going to start by sanding this piece with a 220 grit sandpaper.
How do I paint a distressed look?
Prepare Your Space. Start by laying down drop cloths and preparing the area. ... Sand and Clean the Piece. Sand the surface of the piece. ... Paint the Piece. ... Apply Wax and Top Layer of Paint (Optional) ... Distress the Piece with Sandpaper and Steel Wool. ... Apply a Stain (Optional) ... Protect the Finished Piece with Polyurethane.
How do you Antique already stained wood?
1:002:18Create a Distressed Wood Finish with Varathane Ultimate Wood StainYouTubeStart of suggested clipEnd of suggested clipSo you're going to want to put on the layer let soak in for about 30 seconds. And then wipe off theMoreSo you're going to want to put on the layer let soak in for about 30 seconds. And then wipe off the excess. Let your project dry for one hour and if you want to protect the gorgeous finish.
How do you Antique over stain?
0:142:24How to antique furniture. Distress. Stain. - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst sand the sharp edges such as the front of the legs or any corners if your piece of furnitureMoreFirst sand the sharp edges such as the front of the legs or any corners if your piece of furniture has carved details sand those areas as well start by lightly sanding.
How do you use antiquing gel on cabinets?
9:2414:02Antiquing Glaze on Furniture and Cabinets - Golden PaintworksYouTubeStart of suggested clipEnd of suggested clipFirst just take off a little bit at a time be careful you don't take it off the center panel atMoreFirst just take off a little bit at a time be careful you don't take it off the center panel at least not too much. Okay that one and then this one down. Here. Then finish off on the actual.
How to get rid of old cabinets?
1. Prepare your cabinets. Remove the cabinet doors, as well as the hinges, knobs and other fixtures. The process of antiquing cabinets is much easier, and you will get more streamlined results if you take your cabinets apart before attempting an antiquing treatment.
How to make glaze opaque?
Adjust the opaqueness of the glaze by adding more water or glaze medium, as per your personal preference. Brush the glaze onto the cabinet. You may use a paint brush or a foam brush. Wipe off excess glaze using a cloth or paper towel. Repeat glazing until you get the desired effect.
Can I glaze a cabinet?
Glaze only 1 cabinet at a time. Choose a glaze. You may opt to mix a brown, umber or amber water-based paint with water or a store-bought glaze mixture, 3 parts paint to 1 part water/glaze medium, or you may use stain. Adjust the opaqueness of the glaze by adding more water or glaze medium, as per your personal preference.
Can white cabinets be antiqued?
Antiqued cabinets may be complimentary to a variety of housing designs and decorative aesthetics. White cabinets may be antiqued in a number of different ways, as the white backdrop readily offsets faux finish treatments. Whichever method (s) you choose to use for the antiquing effect, follow these steps for how to antique white cabinets.
How to make an antique door look classy?
Wood glaze is the easiest way to achieve a classy antique look. Choose a tinted glaze with a rich wood tone. Mix it with water according to the instructions, then brush it lightly over the door. Immediately wipe off excess with a dry cloth.
How do I stain a wood door?
Brush the stain over the door. Cover it evenly if the door is new. Cover just the lighter spots of wood if the door is partially painted or weathered already. Immediately wipe it with a dry cloth to rub it into the wood and remove the excess. Buff with a second cloth if necessary to work the stain into crevices.
How to make a paint look old?
In order to make a fresh coat of paint look old, you'll need either a wood glaze or a crackle medium. Here's a description of the two approaches: Wood glaze can be used to leave scratchy streaks over existing paint. Paint the door and let dry. Dip an old, straggly brush in the stain and wipe most of it off.
How long should I leave crackle paint on wood?
Check the label for timing instructions, as some crackle mediums must be left on for an hour or more before painting the wood. 9. Apply protective finish (optional).
How to antiquate a door?
Antiquing a door while it's attached to the wall makes the project harder than it needs to be. Lay the door over a large work table in a well-ventilated room or outside. Cover the floor with a drop cloth to catch spills. 3. Chip or scratch the wood (optional).
Is it hard to find antique wood doors?
Antique, solid wood doors are expensive and hard to find. Whether you are going for an old farmhouse look or a restored museum piece, you can achieve the look at home instead. Besides saving money, you'll get to express yourself with your perfect style. Steps.
How do I paint a door?
Sand the door gently with a medium- to fine-grit sanding block to create a grippable surface for the paint. Sand both sides of the door, as well as the edges, if you intend to paint those areas. Otherwise, only sand the side to be painted. Wipe the dust away with a tack cloth.
How to make a dark brown door look old?
Mix half water, half dark brown latex paint in a small disposable container, stirring it with a stir stick. Apply the paint to the door in quick, bold strokes of the paint brush. Rub most of the watery paint away with a clean rag. This enhances the look of age on the door.
How to make a thin wax layer on a door?
Rub a candle over the edges, corners and as much of the door as possible to create a thin wax layer on the door. Brush away excess wax with your hand.
Why is my door not closing properly?
Too much paint on the edge of the door may cause the door not to close properly. Writer Bio. Kathy Adams is an award-winning journalist and freelance writer who traveled the world handling numerous duties for music artists.
How do I protect a door from a sagging door?
Place old newspapers beneath the door. Cover windows, if any, handles and other hardware with painter's tape and newspaper to protect them.
Do modern doors look like antique doors?
Some modern doors are designed to have the same style as antique doors, but simply look too new. Faux-painting techniques and a little distressing of the wood or finish makes that new door look like an antique. As an added element of fun, apply coats of paint in varying colors, allowing layers to show through as you sand away some of the paint, ...
How to make a cabinet door look rustic?
Apply it with a paintbrush to areas on the door where natural wear and tear would occur to create rustic appeal, especially around the hardware and the edges of the door. Immediately rub off the stain with a towel or rag before it completely soaks into the wood. The stain will become lighter as you rub, giving the door an antique look.
How to clean paint off of cabinet doors?
Mix a small amount of liquid detergent with warm water in a bowl and sponge the surface of the cabinet door thoroughly to remove any grease, grime, or dust off it. Paint will not adhere properly to its surface if it is not clean.
How do I remove paint from a door?
Use a fine to medium grit sandpaper and carefully sand the entire surface of the door, including the sides and any grooves to completely remove any existing paint or varnish on the door . Brush off the surface to remove the residue.
How do I paint a white door?
Paint the door in white or any neutral color with a sponge roller, working in one direction and using even strokes. Allow one coat to dry before applying another coat. Leave the door to dry overnight.
How to get antique glaze off of cabinet doors?
Add more antique glaze to the edges of your cabinet doors. Wrap a rag around your index finger and wipe off any excess glaze. Let glaze dry for 24 hours. Apply a light coat of wood sealant.
How to make antique cabinets look vintage?
Choose your antique stain shade according to the cabinet’s base color. If the base color is white or cream, use a mid-tone stain. If the color is honey or caramel in tone, use a medium or dark stain. If it is dark, use the darkest stain you can find. The higher the contrast between the stain and base, the more vintage the look of your cabinet. See more cream kitchen cabinets here for ideas.
How to get a cottage chic look?
For the process all you need are some basic things. Begin with gathering a pair of gloves, sponge, sandpaper and paint brushes. Next, get your paints ready and your good to go. Below we’ll cover how to paint kitchen cabinets to look antique.
What is antique stain?
The antique stain is basically the shade that is painted over the base color along the edges and corner to give the base color the necessary drama. As mentioned before, there needs to a stark contrast to make the vintage look really stand out.
How to get rid of circular marks on wood door?
Smooth out the circular marks. 2. Using a paintbrush – Dip a brush into the glaze, wipe of excess. Brush glaze onto door by going in the director of the wood grain. TIP: Use a rag to wipe off portions of the applied stain; this will result in discolorations that will help the wood look worn not too dark and “fake”.
How to get a distressed look on cabinet doors?
From the sides of the cabinet doors to the edges of the molds, you can scrape the paint a little by using a sand paper to give your cabinet a naturally distressed look. You can also take a hammer or small chisel to create dents on the wood for added charm. Ensure that you do not overdo it.
Can you use antique stain on wood?
You can try it out on a scrap piece of wood if the thought of applying the stain without any practice intimidates you. But mostly, you can just go ahead, pick up a sponge, dip it in the stain and carefully apply the antique stain on the sides and corners to give your kitchen cabinet that final touch of vintage charm.
When were doors made?
Most interior and exterior doors built between 1750 and 1940 are made with frame-and-panel construction, producing the common and easily recognized panel door that gets its name from the vertical panels that appear to float between flat cross and side pieces, called stiles and rails, that hold them in place.
What were the doors like in 1900?
Doors for houses built after 1900 tend to be more standard in size and features, which made it easy for builders to use them interchangeably on a wide range of houses. Another cost- and labor-saving innovation was the move to flat-panel doors, like the cabinet doors in kitchens of the period.
What is a horizontal panel door?
The horizontal five-panel door is a favorite of the bungalow era. Sometimes one or two panels are replaced with glass, especially on exterior doors. A minor repair to the surface of a panel door usually involves filling gouges and cracks with wood putty, followed by sanding and several coats of paint.
How many panels are there in a door?
The panels—usually four to six per door—can be almost pancake flat, at crisp right angles to the stiles and rails. More typically, however, they are beveled on all sides to create what’s called raised paneling.
Do building supply stores still stock wood doors?
Many building-supply stores still stock wood doors, but in some circumstances, you may want to consider a contemporary molded door. Unlike the architectural puzzle of a century-old door, they are cast over a honeycomb-like core, then covered with either a paint-ready finish or veneer.
Repairing an Antique Door
An antique door is a unique problem, because it’s a small enough job that it seems fairly easy but important enough that you don’t want to mess up, since doors are so highly visible. The most common repair that needs to be done on antique doors is usually patching old hinge gains and latch holes with a wood Dutchman.
Refinishing an Antique Door
This can be quite a process to do correctly, so it’s probably worth your while to check the area and see if there’s a professional carpenter who can at least do some of the work for a reasonable rate.
