Replace it by following these steps with replacement part #WPW10006355:
- Unplug the washer and turn off the water lines. ...
- Remove the water hoses from the rear of the machine. ...
- Set the machine on its front. ...
- Remove the shield. ...
- Remove the old shift actuator. ...
- Install the new shift actuator. ...
- Reinstall the shield.
- Set the washer back upright. ...
Is there a Repair Manual for a whirlpool washing machine?
Our Whirlpool washing machine repair manual will help you to diagnose and troubleshoot your Whirlpool washer problem, cheaply and easily. See easy to follow diagrams on how to take apart your machine and replace the broken washer parts. Learn how to service and maintain your Whirlpool washing machine yourself and keep it running like new.
Where is the motor actuator on a washing machine?
Your engine’s exhaust pump and the motor actuator on your washing machine are located at the bottom of the tub, where the actuator is part of the engine that functions to replace the shifter. The first thing you have to do is, you must first check the drain pump located at the bottom of your crankcase.
How do I Reset my Whirlpool front load washer?
The following steps should be used to reset your Whirlpool washing machine: Turn off the washer. Turn the mode dial to NORMAL. Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
Why won’t my washing machine timer move?
Besides, the possibility of filtering the water in your washing machine on the pipe to the washing machine is being blocked. If a washing machine cycle cannot function properly while you are washing your clothes, the timer on your washing machine may refuse to move. The thing you need to do is, you can change your timer in the flushing process.
How do I find the actuator on my Whirlpool washer?
0:425:11How To: Whirlpool/KitchenAid/Maytag Shift Actuator WPW10006355YouTubeStart of suggested clipEnd of suggested clipJust catch any water that might come out also the hot and cold are usually labeled so make sure youMoreJust catch any water that might come out also the hot and cold are usually labeled so make sure you remember which side is which so when we put them back on you get them on the right side.
What does the actuator do on a Whirlpool washer?
The actuator serves several functions. It has a synchronous motor that shifts the splutch cam ring and monitors the position of the splutch. It also houses a transmission speed/position optical sensor.
What does the shift actuator do?
Shift Actuator - 120V 60Hz Specifications. This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
What causes a Whirlpool washer not to agitate?
1:232:38Top-Load Washer Won't Agitate — Washing Machine TroubleshootingYouTubeStart of suggested clipEnd of suggested clipThe coupler can wear out over time or fail if the washer is overloaded causing the tub not toMoreThe coupler can wear out over time or fail if the washer is overloaded causing the tub not to agitate.
Why is my Whirlpool washer stuck on sensing?
A Whirlpool washer should only stay in the sensing stage for 2-3 minutes. When it gets stuck on sensing, it's likely because of a faulty water inlet valve, shift actuator, drive motor, or main control board. A fault at any of those parts can prevent the washer from advancing past the sensing stage.
Why is my washer making a grinding noise when agitating?
The rotating motion of the agitator is permitted by a component called agitator dogs. You can find these in the top part of the agitator in the center column. After frequent use, it's common for agitator dogs to wear out and start slipping. As a result, you will hear a grinding noise during washing machine agitation.
What does a washer splutch do?
The Splutch Cam Assembly transfers energy from the motor to the transmission in your washer, allowing it to spin. This repair is relatively easy to complete yourself, and to help you out we have an easy Step-by-Step Repair Guide for you today.
How do you change a shift actuator on a Maytag washer?
1:143:47Maytag Washer Shift Actuator Replacement -- Blinking Lid Lock ...YouTubeStart of suggested clipEnd of suggested clipAnd this red thing here is the shift actuator first thing I'll do is remove this belt cover justMoreAnd this red thing here is the shift actuator first thing I'll do is remove this belt cover just spin off a couple screws. And that allows me to get to the shift actuator.
What does the shift actuator do on a Kenmore washer?
W10006355 Washer Shift Actuator Compatible with Whirlpool, Maytag, Kenmore Washer Machine. This part may be referred to as a Shift Actuator or Mode Shifter. This part changes the transmission from agitation to spin mode.
Why will my washer spin but not agitate?
If your washer won't agitate but spins, a broken agitator may be to blame. The agitator is the centerpiece in a top load washer that agitates and moves the clothes through the water during the wash cycle. The output shaft of the transmission is splined to the agitator to secure it in place.
What causes a washer not to agitate or spin?
If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. (Note: Direct-drive washing machines do not have belts.)
Why won't my Whirlpool washer spin or agitate?
Common solutions for: Whirlpool Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washer transmission.
How do I fix the actuator on my washing machine?
1:022:57Whirlpool Top Load Washer Replace Shift Actuator #W10597177YouTubeStart of suggested clipEnd of suggested clipInstall the new shift actuator by aligning it on the gear case making sure the arm is inserted intoMoreInstall the new shift actuator by aligning it on the gear case making sure the arm is inserted into the shift lever thread the mounting screws to secure. Connect the wire connector.
What does a splutch do?
The splutch cam kit is mounted on the drive shaft at the bottom of the washing machine. It transfers energy from your washer's motor to your washer's transmission, allowing the washer to spin.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load WasherError CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.7 more rows•Apr 11, 2022
Why does my Amana washer won't spin?
If your washer is not spinning and water is standing in the tub, check for proper drain hose installation, especially if your “spin” light is on. This light will turn on after 10 minutes of the drain pump being on with no water level change. This can happen if the drain hose is too far down the drain pipe.
How to remove shift actuator?
Remove the old shift actuator. Unscrew the two screws holding the part in position, then pull the part away and rotate it to get the screws. Next, unclip the wire harness and set the old part aside.
How to remove water lines from a washing machine?
Remove the water hoses from the rear of the machine. Mark the hot and cold lines so you don’t mix them up during reinstallation, loosen them with pliers, and then set them aside. Also, remove the drain line from the wall so it doesn’t pull tight.
How to reset Whirlpool washing machine?
The following steps should be used to reset your Whirlpool washing machine: Turn off the washer. Turn the mode dial to NORMAL. Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
How to reset Cabrio washer?
If your washer is still not working correctly, you can try the Cabrio reset procedure. Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.
Whirlpool Washer Repair
Our Whirlpool washing machine repair manual will help you to diagnose and troubleshoot your Whirlpool washer problem, cheaply and easily. See easy to follow diagrams on how to take apart your machine and replace the broken washer parts. Learn how to service and maintain your Whirlpool washing machine yourself and keep it running like new.
Whilpool Washer Troubleshooting
Our Whirlpool washing machine repair manual can help you troubleshoot your machine.