How to Replace the Agitator Coupler in Your GE Washer
- Open up your washer lid. ...
- Now that you have gained access to the agitator coupler, use a socket and ratchet to unthread the bolt that secures the component to the inside of the washer. ...
- Grab your new coupler and slide it onto the drive shaft. ...
- After the new agitator coupler is installed, retrieve the agitator and align it with the coupler. ...
How do you change the agitator dog on a GE washer?
0:421:41How to Replace a Direct-Drive Washer Agitator Dogs ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitatorMorePull the dust cap out of the agitator. Use a 7/16 socket with an extension to remove the agitator bolt. Pull the top auger off of the agitator assembly. And set it on a work surface dump.
What does an agitator coupler do?
The agitator coupler connects the agitator to the agitator shaft. Common symptoms of a damaged coupler include: a grinding sound during the wash cycle, the washer refusing to agitate or spin, or the washing machine shakes and moves during the wash cycle. Unplug the washer and pull the agitator straight up.
How do you remove the agitator plate on a GE washer?
1:054:07How To : GE Agitator Assembly WH43X1003 - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou may have to while you have the edge that are lift it up a little bit put some straps underneath.MoreYou may have to while you have the edge that are lift it up a little bit put some straps underneath. It. And once you have the straps underneath you can lift up on it and break it. Free.
How do you remove an agitator bolt?
0:474:08How To: Whirlpool/KitchenAid/Maytag Agitator Bolt WPW10076270YouTubeStart of suggested clipEnd of suggested clipOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonnaMoreOnce you have the socket on the agitator you'll notice that it spins the whole tub. So you're gonna have to reach down and hold it while you break the bolt. Free.
How do I know if my agitator coupler is bad?
If the washer fills to the selected level and you hear the motor running but the washer is not agitating, set the dial on the spin cycle. If the washer drains the water and you hear the motor running (making noise but not spinning), it is likely you have a broken motor coupler.
How do you remove agitator coupler?
1:062:58How To: GE Agitator Coupler Kit WH49X10042 - YouTubeYouTubeStart of suggested clipEnd of suggested clipCoupler. If by chance your agitator are stuck on there pretty good and you can't get it off you canMoreCoupler. If by chance your agitator are stuck on there pretty good and you can't get it off you can run a couple straps underneath the agitator. And use those to pull up on it.
Can you unscrew the agitator from a washing machine?
With the bolt sufficiently loosened, you can pull the agitator straight up to remove. Alternatively, on some models where the agitator has an upper and lower section, you may need to use a square drive bit to unthread a retainer that will allow you to pull the upper portion of the agitator off first.
How do I clean the inside of my GE agitator?
Remove the fabric softener dispenser from the agitator. Allow the washer to fill and proceed to the wash phase. Allow the washer to agitate for about 5 minutes. Lift the lid and use a long, slender soft brush to clean the inside of the agitator.
How do you remove the agitator from a top load washer?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd then write down the center of the agitator as a little wound yard remove that just hold theMoreAnd then write down the center of the agitator as a little wound yard remove that just hold the agitator as you unscrew anticlockwise.
What size is an agitator bolt?
Washer agitator bolt with rubber gasket and thread sealant. Head is 7/16 inches in diameter.
How much does it cost to fix a washing machine agitator?
$350 to $575On average, expect to spend $350 to $575 for washing machine agitator replacement. A broken agitator in a washer is a significant fix. If the agitator is broken, the clothes will not oscillate back and forth. The agitator is critical since it moves the clothes through a combination of detergent and water.
Why does my agitator keep coming off?
The agitator could come off the base if not seated properly. It can easily be snapped back in place: Line up the grooves in the agitator auger with the agitator base. Turn counter-clockwise until it locks into place.
What is the purpose of an agitator in a washing machine?
AGITATOR ACTION Rubs against clothes to help break apart stains and loosen soils.
Why have an agitator in a washing machine?
Traditional agitators are tall spindles located in the center of the wash basket that twist (or agitate) back and forth, rubbing against the clothes to help break down dirt and other particles.
How does a dual action agitator work?
The Dual Action Agitator top portion (auger) only rotates in one direction as it “locks” onto the agitator in one direction and rotates freely in the other. This auger action moves clothes downward in the center towards the agitator base where mechanical cleaning action takes place.
Which is better agitator or impeller?
Washing machines with an impeller tend to wash your clothes better than with an agitator. That means that, generally speaking, front load washers or top load washers without an agitator will do a better job at getting rid of tough stains and dirt off your clothes.
How to reattach agitator to washing machine?
After the new agitator coupler is installed, retrieve the agitator and align it with the coupler. Then, push down on the agitator to reattach it to the washing machine.
How to get agitator out of washing machine?
Open up your washer lid. Reach inside your appliance to grab the bottom of the agitator and carefully pull the component out of your washing machine.
How to attach a coupler to a drive shaft?
Grab your new coupler and slide it onto the drive shaft. If it’s not going down all the way, rotate the coupler to line up the teeth with the shaft, and then push the component further down. Once the coupler is in place, secure it with the bolt you removed earlier.
How to remove agitator on GE washer?
To remove agitators on these models, this fastening bolt must first be removed. To access the bolt, remove the cap at the top of the agitator — this can usually be done either by hand or by prying with a screwdriver.
What is the agitator on a washing machine?
Top-loading washing machines usually use a part called an agitator (which looks like a large screw or drill bit in the middle of the washing compartment) to "stir" (or, in other words, "agitate") the clothes being washed. If the agitator stops working properly, maintenance and repair work may require removing it.
How to keep agitator smooth?
Take the opportunity to lubricate the shaft. Older models of washing machines usually have a metal shaft under the agitator that requires occasional lubrication to keep the motion of the agitator smooth. As long as your have access to the shaft, ensure it stays in good working order by using a small amount of petroleum jelly (often called by the brand name Vaseline) to lubricate it.
What to do if agitator won't come off?
If the agitator won't come off, call a repairman . The agitators in many models of washing machine (particularly more recent ones) aren't designed to be removed normally — instead, they require special tools or techniques that only trained service people have access to. In these cases, you may not be able to remove the agitator even if there is no obvious bolt holding it in place, so your only option is to enlist the help of a mechanic.
How to clean a washing machine with hot water?
Cover the bottom half of the agitator with hot water. To begin, fill the washing compartment with about six inches or so of hot water — enough to completely cover the bottom of the agitator. This will help loosen any built-up soap and chemicals, making removal slightly easier.
Why does my washing machine stop agitating?
Know that if your machine is no longer agitating your clothing during the wash cycle, the problem may not be with the agitator itself. Problems with the transmission, agitator coupler, motor, belt, and clutch can all cause the machine to stop agitating.
How to fasten a agitator?
Fasten a loop of strong rope around the agitator. Grab a strong piece of rope about five feet (one and a half meters) long. Fold it over on itself at its midway point and loop it through itself to fasten it between the fins on the agitator neck. Give it a firm upward yank to tighten it and ensure it's secure.
How to remove a coupler?
strap to pull up on the coupler, it will give you better leverage. The last resort would be to use a "Dremel" tool or similar device to "cut" the coupler into pieces and remove it.
How to check if a washer is broken?
want to check the motor, counterbalance, and base of the washer to see if anything is loose , broken or bent. check the base to see if the motor and carriage has been banging or rubbing against the base or housing, indicating the top "apron".has started to "droop". You didn't mention any leaks or discoloration inside the cabinet, so you'll need to check and make sure the hub nut isn't loose and check the agitator and spin tube shaft for any excess wear, play, and discoloration, that could create a loud banging noise in the spin cycle. Thanks,
What is a coupler on a transmission?
Coupler goes between the transmission and the agitator. Includes hold down bolt. Hold down bolt no longer sold seperate.
When installing a coupler onto a shaft, do you have to get the splines lined up?
Answer J, When installing the coupler onto the shaft, you have to get the splines lined up and sometimes this requires twisting the coupling to get it to slide in place. Also, make sure that the splines... show more
Where is the WH49X10042?
Answer Chris, Per the model number you have given, WH49X10042 is the coupler for your unit and is located under the agitator.
Can a coupler be damaged if you replace the agitator?
Answer Ben, If you have only replaced the agitator then the agitator coupler could be damaged and not allowing the agitator to sit right .
Can a coupler seize?
Answer RK, It doesn't sound like you're doing anything wrong. The coupler can seize to the agitator shaft, after a few years of usage . After the agitator and coupler bolt are removed, a few drops or rust... show more
How to install agitator in washer?
Insert the new agitator into the washer. Insert the agitator bolt into the agitator and tighten it, using the socket wrench.
How to remove agitator coupling?
Remove the socket wrench from the extension and socket. Insert the extension into the agitator and line up the socket with the bolt hole. Tap the top of the extension with a mallet to loosen the agitator coupling inside the agitator.
How to access agitator on a stove?
Open the lid on your appliance to access the agitator. Wiggle the cap off the top of the agitator to access the bolt inside the agitator.
How to make a loop with rope?
Cut a piece of rope at least 6 feet long. Use a square knot to tie both ends of the rope together to create a large loop.
What to do if washer doesn't agitate?
The washer fills with water and drains , but won't agitate or spin even though the drive motor runs. The motor buzzes when the motor is running. You smell burning rubber or plastic when the motor runs. If the washer fills and drains but doesn't agitate or spin, replace the motor coupler with part 285753A.
How to release clips from washer?
Release the clips that secure the cabinet to the washer’s back panel. Using a slot screwdriver, pry the clips forward to release the clips from the slots in the top panel.
How to put a cog on a motor?
Carefully push the remaining motor coupler cog onto the motor shaft. Tap the cog into place using the handle of a slot screwdriver and a hammer until the drive motor shaft is flush with the outer surface of the cog base.
How to put a cog on a transmission?
Carefully push one of new motor coupler cogs onto the transmission shaft. Tap the cog into place using the handle of a slot screwdriver and a hammer until the end of the transmission shaft is flush with the outer surface of the cog base.
How to remove the bottom clip of a drive motor?
Release the bottom clip using a slot screwdriver and then remove the bottom clip. The drive motor is heavy. Place one hand under the drive motor to support the motor and prevent it from falling as you remove the top retainer clip. Release the top retainer clip and pull the drive motor off.
How to position a washer on a cabinet?
Tilt the back of the cabinet up slightly and keep the front lip of the cabinet on the floor. To position the front lip under the washer frame, push the base of the cabinet forward with your foot to slide the front lip of the cabinet under the front base of the washer. Then lower the back of the cabinet so the holes in the back of the sides of the cabinet engage the alignment tabs at the back of the sides of the washer base.
What to do if your top load washer spin basket is damaged?
If the spin basket on your top-load washer is damaged, you can replace it with a new one. Just follow these step-by-step instructions.