Unclip the cord, extract the socket and screw in a new light bulb," Sansing says. "If the blow mold uses a larger base size light, remove the screws that hold the light kit (socket) in place, remove it and screw in a new bulb, but never use more than a 40W bulb." She also recommends using LED light bulbs instead of traditional incandescent ones.
How do I change the light bulb in my air blown light?
A: To change the light bulb, first unplug and deflate the item. Next, unzip the bottom zipper (or zipper closest to the bulb) and locate the bulb needing replacement. Remove the light cover by squeezing it sideways and replace the bulb. Airblown light bulbs are either mini lights or C7 watt bulbs, which can be found at hardware and lighting stores.
Can you change the light bulb in a blow mold?
If your blow mold uses this, you'll find it on a single light cord with a clip. Take out the burnt bulb and replace it with a new one. Blow molds also can use regular incandescent bulbs, which can be changed out just like a regular light bulb.
Do blow mold decorations need to be plugged in?
When a blow mold does include lights, you'll see that some require a simple plug-in (which is usually included) or will run on batteries. How do you change the bulb in blow mold decorations? There are two types of light bulbs that are used in blow mold decorations. The first is a C7 bulb that's commonly used for night lights.
What kind of bulb do I need for a blow mold?
The first is a C7 bulb that's commonly used for night lights. If your blow mold uses this, you'll find it on a single light cord with a clip.
Can you replace lights in yard inflatables?
9:1610:27Replacing LED lights in your yard inflatables - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then snap it on a little bit better. And there you go now you have it back up repeat that sameMoreAnd then snap it on a little bit better. And there you go now you have it back up repeat that same thing for your other lights that are in your inflatable. And you've replaced your leds.
How do you fix an inflatable light?
0:5212:58Fixing Yard Inflatable Decorations with Dim Lights. Yard Blow ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just sitting there and it had to has a little tab that cooks on the back of this right thereMoreAnd just sitting there and it had to has a little tab that cooks on the back of this right there that you can see. If you can see it or not the little tab comes off and that's what holds it onto.
How do you change a bulb in a yard?
1:383:51How to Change Low Voltage Landscape Lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipPiece that basically just twists. Off. It's got a rubber seal. So that's what keeps it waterproofMorePiece that basically just twists. Off. It's got a rubber seal. So that's what keeps it waterproof once that cover is off all you have to do is pull up on the bulb.
How do you change a twist bulb?
0:241:47How to Change your household lightbulbs - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo use a cloth to grasp it for removal in most houses bayonet mount bulbs are very common to removeMoreSo use a cloth to grasp it for removal in most houses bayonet mount bulbs are very common to remove one press up on it slightly and twist anti-clockwise. It should come out easily.
How do you change an LED light bulb outside?
0:562:51How to Quickly Remove the MR16 bulb from our LED Spot Light by ...YouTubeStart of suggested clipEnd of suggested clipIt under the rim of the bowl just right under there now pull on it that's it light bulb comes rightMoreIt under the rim of the bowl just right under there now pull on it that's it light bulb comes right out right in your hand. That's all that's to it it.
How do you repair inflatable decorations?
0:103:00How to Repair Inflatable Santa Claus Christmas Holiday DecorationYouTubeStart of suggested clipEnd of suggested clipSo I found these vinyl patch repair kits at Home Depot ended up buying three of them. The piece ofMoreSo I found these vinyl patch repair kits at Home Depot ended up buying three of them. The piece of plastic measures. Two feet long by six inches tall. And you get that you get the adhesive.
How do you remove outdoor light cover?
0:000:57how to remove outdoor light fixture - YouTubeYouTubeStart of suggested clipEnd of suggested clipSome new light fixtures might be held by two screws on the sides remove the nuts by hand or you mayMoreSome new light fixtures might be held by two screws on the sides remove the nuts by hand or you may need to use a wrench step three do me a favor and smash that bike.
How do you remove landscape lights?
Instructions. Dig up dirt around the existing landscape light to expose wiring. Unscrew both of the electrical caps and disconnect only the fixture wiring keeping the other two wires together. Screw them back together with the electrical caps.
How do I change my outdoor spotlight?
0:167:19How To Install Replace Outdoor Light Easy Simple - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf there's any caulking. Around the light fixture if there is you do want to take a knife and removeMoreIf there's any caulking. Around the light fixture if there is you do want to take a knife and remove that because if not when removing the light fixture you might remove the paint from the wall.
How do you remove a lightbulb cover?
0:172:00Replace a lightbulb in a flush mount light fixture - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn you'll then need to unscrew that by hand by turning it counterclockwise or possibly use a pair ofMoreOn you'll then need to unscrew that by hand by turning it counterclockwise or possibly use a pair of pliers. Or channel locks to get it.
How do I remove a light bulb?
0:171:09How to replace a light bulb - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo do this. And push it in and twist anti-clockwise releasing the bulb from the holder. And thenMoreTo do this. And push it in and twist anti-clockwise releasing the bulb from the holder. And then once you've got your new bulb. Each a bulb once again using a cloth to push it over the glass.
How do you remove a bayonet bulb?
Most light fixtures use bayonet caps. To remove a bayonet light bulb, hold the bulb housing firmly, push the bulb into the housing and twist in an anti-clockwise direction. Withdraw the bulb.
How do you change an inflatable fuse?
2:218:41How To Change A Fuse In Your Airblown Inflatable DecorationYouTubeStart of suggested clipEnd of suggested clipInside you will see two fuses right here. Now each brand new inflatable comes with an extra fuseMoreInside you will see two fuses right here. Now each brand new inflatable comes with an extra fuse this one happens to have an extra fuse. And the this right here on the left.
Why do inflatables stop working?
Consider Placement. An inflatable that fails to inflate could be sitting in the wrong spot. Make sure the inflatable is completely unfolded and lying flat on a level surface. Check that the fan used for inflation is sitting on a level, stable surface.
Can inflatables be repaired?
Stitching or special repair patches fix damaged inflatables. The downside to inflatables is that they are prone to leaks, punctures or tears that render them unusable. Rather than discarding your favorite holiday inflatables, many of them can be patched with tape or a vinyl repair kit.
How do you fix an inflatable decoration motor?
0:163:48Easy Fix For a Broken Airblown Inflatable - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis pull it out from Olaf. And do the same with the other inflatable. Pull it out tight littleMoreThis pull it out from Olaf. And do the same with the other inflatable. Pull it out tight little tight now we're one and make sure the flat one goes with the flat.
Fixing Your Snow Globe Lights
Check the lights in your snow globe a few days before you plan to put up the decorations. This will make it easier to replace any faulty bulbs. Various companies make electric snow globes, so the bulbs are changed a little differently depending on the manufacturer.
Other Electric Snow Globes
If you have a Gemmy snow globe, you will have to deflate it before changing the bulbs. Unzip the zipper closest to the bulb; it may or may not be on the bottom. These also have light covers, which you will need to squeeze sideways to free the bulbs.
Caring for an Outdoor Snow Globe
Outdoor snow globes do well in normal and light weather conditions, including gentle snowfalls and rain, but you must protect them from the harsher elements. They can survive below-freezing temperatures, but if the weather drops below 20 degrees Fahrenheit or so, bring your decoration inside.
How to get air out of inflatable?
You may be able to audibly hear the hissing as well. If you’re really in a jam, you can use a classic mechanic’s trick. Get a spray bottle and some soapy water, and start spritzing it all over your inflatable. An area with air leaking out of it will start blowing large bubbles and make itself known!
What to use for small tears in inflatables?
For small tears, a simple sewing kit will do the job if you know how to use it. This method of repair will be the least visible to onlookers, but if you bunch the fabric too much it could create a strange divot in your inflatable. For holes and tears in highly visible areas, we recommend Fabric Repair Tape.
What to do if your blower is not working?
If you still don’t get any action from your blower, try a different outlet if possible or at least plug another device into the same outlet to make sure the outlet is live. If your blower is working, but the inflatable isn’t inflating all the way, you likely have a tear in your fabric.
Can an inflatable blower have LED lights?
Your existing inflatable blower may have an LED plug attachment in it if it has internal LED lighting. If that’s the case, you may be able to find a blower that’s compatible with your existing lights.
Can you use duct tape on inflatables?
For major tears, we recommend Transparent Duct Tape. It’s not the sexiest solution, but it’s extremely effective for repairs. This duct tape is weather-resistant and should last the life of your inflatable. Try to place it on the inside of the inflatable to protect it from the elements as much as possible. The only downside this method has is the duct tape may be visible if there’s a light shining behind it.
Can you replace an inflatable blower fuse?
Replacement fuses are very cheap, so if your inflatable has a blown fuse, it’s an easy fix to swap a new one in. If those steps fail, sad to say you need to look into replacing your inflatable blower. Here are the best ways to go about it.
Can you put inflatables outside?
When it comes to your best yard inflatables, placing them outside inevitably puts them in harms way for potential damage. It could be anything from wild animals to a bad snow storm that could cause your inflatable to break, leaving you with an expensive pile of fabric on your lawn and not much else.
Where can I buy airblown bulbs?
You may also be able to purchase light bulbs through online retailers, like buylighting.com.
How to dry airblown?
HEAVY RAINFALL/MELTING SNOW: If your Airblown has become soaked with water from a heavy rainfall or melted snow and you are having trouble inflating it, move the unit to a dry location and plug it in. The fan will dry the unit. If there is a large amount of water, open the zipper closest to the soaked area and drain the water.
What temperature do airblown inflatables operate at?
FREEZING TEMPERATURES: Airblown Inflatables will operate at temperatures below freezing. However, we do not recommend operating the item if temperatures drop below 14° Fahrenheit (-10° Celsius).
How to connect an airblown 4ft inflatable?
ADAPTORS: For 4FT inflatables, unplug your Airblown to check the adapter connection. There is a small groove on the adapter plug that matches a raised notch on the inside of the adapter port. Make sure the adapter is connected so that the notch slides securely into the groove. Plug the Airblown back into the wall outlet or heavy-duty outdoor extension cord.
When does an airblown inflatable start inflating?
A: Under normal conditions, an Airblown Inflatable should begin inflating automatically as soon as it’s plugged in. If it has animation or motion, these actions should also begin upon plug in. If not, please check the following:
Do airblown globes have zippers?
Check for hidden zippers in the seams. If you have a globe, there can also be zippers on interior characters inside of the globe. Please double-check to make sure all are completely zipped.
Does Gemmy Industries sell airblown fans?
A: Unfortunately, Gemmy Industries does not sell or maintain a stock of replacement fans or motors for Airblown Inflatables. However, motors can be purchased online at Yard Inflatables. Although we cannot provide support to assist you in the process, Airblown collectors have successfully taken care of these replacement needs by purchasing inexpensive fans or motors and transferring them to the item in question.
How to fix a leaky inflatable?
If you can't find it, hold up a piece of paper near the inflatable when the fan is on during a non-windy day; the paper should move near the leak. Place a piece of masking tape near the hole to mark the spot. Turn off the fan and allow the air to escape the inflatable.
How to repair a hole in a tent seam?
If the hole is along a seam line, first repair the seam using a tent-se am repair adhesive, otherwise the patch may not work properly. Once the adhesive cures, place a patch over the area using the vinyl repair kit adhesive.
How to repair a tear in nylon?
Pinch the area on either side of the nylon tear together, then stitch through both sides of the tear at one end of the damage. Pull the thread until the knot reaches the nylon, then loop your hand back over to near where you began, pushing the needle through the nylon half an inch or so away from the first stitch, going through the nylon on both sides of the hole once again.
Can you use a fan blower if it makes a noise?
Do not use a fan or blower if it sparks, makes odd noises or shows damage to the electrical cord. Replace the device.
Can you repair an inflatable?
Rather than discarding your favorite holiday inflatables, many of them can be patched with tape or a vinyl repair kit. The exact repair method depends on the extent of the damage and the location of the tear.
How to fix a split in a blow mold?
Depending on the size of the crack or split (and assuming that no part of the plastic is missing), Sansing says you can fix a crack or split in a blow mold with the help of an adhesive, like J-B Weld Clearweld Clear Epoxy Adhesive ( $4.84, amazon.com ). "A simple crack can be reinforced from the inside, using a strip of plastic (cut from a milk jug) and applied to the inner surface, like a Band-Aid, using clear drying epoxy for plastic," she explains. "If there is excess glue on the mold, you can scrape this away with your knife or use a small file."
How to repair a broken blow mold?
"Using a clear-drying adhesive (on the underside of the patch), apply the patch, and tape it down. When you are certain the adhesive has dried, very carefully remove the tape. If any edges come up, repeat the process on those edges only, tape, and wait until adhesive is set and dry."
What are blow molds used for?
Equal parts festive and nostalgic, blow molds are the plastic, light-up figures and ornaments—think Santa Claus, reindeer, and candy canes —commonly used to brighten up lawns, porches, and sometimes roofs during the holidays.
How to clean mold off of paint?
Vannucci says you can easily clean a dirty blow mold by using baby wipes, paper towels, or a soft cloth. "You want to be gentle when you're cleaning the painted areas because the paint is water based, so rubbing too hard might remove it," he explains. "Never use chemical-based cleaners because that will damage the paint. For tougher stains on the unpainted parts of a blow mold you can use dish soap and a brush, but remember to stay away from the paint or the brush will scratch it."
What type of bulb is used in blow molds?
There are two types of light bulbs that are used in blow mold decorations. The first is a C7 bulb that's commonly used for night lights. If your blow mold uses this, you'll find it on a single light cord with a clip. Take out the burnt bulb and replace it with a new one. Blow molds also can use regular incandescent bulbs, which can be changed out just like a regular light bulb. Consider replacing the bulb with an LED for a long-lasting solution.
What to consider when choosing a blow mold?
The most important consideration you want to make when selecting a blow mold decoration is size. Blow mold photos can be deceptive, so be sure to look at the measurements. This will help make sure that you've picked one out that's going to look great on your lawn.
What is a blow mold?
Blow mold decorations are 3D figures created by connecting hollow pieces of plastic together. They became popular in the 1930's and have been a favorite vintage decoration ever since. You can find vintage blow molds or new reproductions of your favorite classic holiday characters.
Can blow molds be used outside?
Blow molds really vary in size. You'll see smaller ones that are meant to be used indoors and larger ones that can be used in or out. If you're decorating with outside blow molds, you'll want to decide where in your yard you want to place it, and then note where it will be viewed from. You want the decoration to be large enough that it can be seen. Also, keep in mind that the bigger the size, the more money you'll be spending.
Inflation & Assembly
- A: Under normal conditions, an Airblown Inflatable should begin inflating automatically as soon as it’s plugged in. If it has animation or motion, these actions should also begin upon plug in. If not, please check the following: 1. LEVEL SURFACE: Ensure the Airblown is on a level surface. 2. FAN(S) SETUP: Make sure all fans are level and plugged directly into a wall outlet or a heavy-dut…
Operation
- A: Please make sure the rotating cuff does not have fabric twisted around it, as this may cause tension and restrict the movement. If fabric is twisted around the cuff, please carefully untwist it. Make sure the Airblown is on a level surface and all other assembly instructions have been followed properly. A: Operation of your Airblown during normal and light weather conditions, suc…
Replacement Parts
- A: If your Airblown is still under the 90-day warranty and parts are available at our corporate office, we typically send parts at no additional charge. Please open a customer service account for assistance. For items no longer under the 90-day warranty, you may be able to purchase parts online through independent vendors like Yard Inflatablesthat maintain a parts inventory. A: If you…
Care & Maintenance
- A: Rips or holes in your Airblown can be sewn by hand (no special thread is required) or taped with clear packing tape. You can also use tent repair tape to patch your Airblown, which can be found at most sporting goods stores. A: Wipe your Airblown® with a damp cloth and allow it to dry before storing away. Use mild detergent if necessary.