How to Replace the Lid Lock on a Maytag Bravos
- Unplug your Maytag Bravos from the electrical outlet. Pull the appliance from the wall to access the rear of the machine.
- Look for the three screws on the back of the control panel. Remove the three screws and rotate the control panel forward to access the washer’s control wiring.
- Find the wires connected to the back side of the touch control. ...
How do I know if my Maytag washer lid is locked?
A lock icon appears on the front of the washer's control panel to indicate the lid is locked and also displays the current progress of the cleaning cycle, depending on the model of your Maytag washer.
How do you lock the lid on a whirlpool washing machine?
Snap the lid lock wires beneath the metal retaining clips. Push the plastic retainer into the small hole near the back of the washer top. Feed the lid lock wire connector through the hole in the top of the washer. Grab the connector and plug it into the control board. Lower the top of the washer.
How do I Turn Off the wash cycle on my Maytag washer?
Pausing the wash cycle is how it can be disabled. A lock icon appears on the front of the washer's control panel to indicate the lid is locked and also displays the current progress of the cleaning cycle, depending on the model of your Maytag washer.
How do I Turn Off the lock on my Kenmore front load washer?
Touch "Cycle Signal" near the front-loading washer's LCD control panel to deactivate the washer's lock controls. The lock icon disappears from the LCD control panel when the lock control is off.
How do I reset my Maytag washer lock?
Door Locked at the end of the Cycle If the washer will not unlock at the end of a wash cycle, unplug the washer or disconnect power. Wait approximately 2 minutes for control to reset. Reconnect power to washer (plug in). Run a "Drain and Spin" cycle.
Why is my Maytag washer lid not locking?
Maytag Washer door or lid won't lock If the door lock is defective, the washer door will not latch properly. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
How do I turn off the lid lock on my washing machine?
3:166:16Washing Machine Won't Spin - Lid Switch Bypass - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'm showing you today is how to bypass. This switch. So that the washing machine thinks theMoreSo what I'm showing you today is how to bypass. This switch. So that the washing machine thinks the lid is closed. So that you can simply drain the water out of your washing.
How do you reset the lock on a washing machine?
Turn the washing machine off and unplug it. If you're in the middle of a cycle, turn the dial or press the button to pause or end the cycle. Wait 5-6 seconds to see if the door unlocks. If it doesn't, turn the machine off by pressing the button or turning the dial all of the way to the off position.
How do you bypass a Maytag lid lock?
1:324:13How to bypass the lid lock on a Maytag or Whirlpool washerYouTubeStart of suggested clipEnd of suggested clipYou slip it right over the top right there. And that's all you need to do.MoreYou slip it right over the top right there. And that's all you need to do.
How do you fix a Maytag lid lock?
2:234:14How to Replace the Lid Lock on a Maytag Vertical Modular Washer ...YouTubeStart of suggested clipEnd of suggested clipThe top panel and prop it securely against the back wall behind the washer. Pull the lid switch/lockMoreThe top panel and prop it securely against the back wall behind the washer. Pull the lid switch/lock assembly out of the washer. Push.
Can you bypass washing machine door lock?
One of the main ways of bypassing a washing machine door lock is by disabling the safety circuit. It is good to note that the process involves cutting of electrical wires. Thus, you need to disconnect your machine from the main power supply. Additional, cutting the cord may void your warranty.
Why is my washer stuck on lid lock?
– Lock striker that presses down on the lid switch may be out of alignment. – A piece of lint or washing machine detergent has built up over time and hinders the locking of the lid. – The control board sees an open lid switch when it attempts to lock.
Why is my lid lock light flashing on Maytag washer?
The Lid Lock Light will flash if Lid Lock has not moved into the Lock Position, the Lock Motor can not be powered, or the Lid is not closed completely due to interference. Some models will lock immediately, while others will not lock until after the wash cycle has started.
How do you manually unlock a Maytag top load washer?
If you remove the top washer panel, you can reach down into the washer and pull the tear shaped tab at the bottom of the door lock and it will unlock the door. On some of the Maytag washing machine models, there is a green plastic rope/string located near the detergent area that if pulled, will unlock the door.
Why is my washer locked and won't open?
The most common cause is water left in the machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.
Why is my washing machine not locking?
0:061:32Top-Load Washer Lid Won't Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou will need to replace it with a new. One the main control board controls when the lid lock shouldMoreYou will need to replace it with a new. One the main control board controls when the lid lock should secure the lid and release it so a faulty board might be the cause of a lid not locking when it.
Press Cycle Signal
Deactivate “lock control” near the front-loading washer’s LCD control panel by touching the “cycle signal.
Select Cycle Signal
Press the ‘Cycle’ and ‘Wash/Cold’ buttons on your front-loading washer for 6 seconds and then release all buttons. A lock icon should appear on the washer’s display screen.
If the lid lock light is flashing
If you’re experiencing problems with your washer and the lid lock light is flashing, the first thing to do is unplug the machine for about 10 minutes and then plug it back in.
The lid keeps locking on the washer
Standing at a corner behind the washer, twist your upper body until you can reach both of your hands around to the front opening. Grasp the insides of both halves and pull forward roughly 6 inches.
How to connect Maytag washer to electrical outlet?
Plug the touch control wire connector into the control board. Re-install the control panel over the control board. Replace the three screws along the back of the touch control panel. Plug the Maytag washer into the electrical outlet.
How to measure for a washing machine lid?
Tape the washing machine lid shut. Measure approximately 6 1/2 inches from each side of the washer moving in toward the front center. Lightly mark the top of the washer with a pencil at the 6 1/2 inch marks.
Still need help? Contact us or schedule service
Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.
Interested in purchasing an Extended Service Plan?
Please click below to learn more on how you can save up to 25% on New Appliance Extended Service Plans within 30 days of your appliance purchase.
Step 1
Touch "Cycle Signal" near the front-loading washer's LCD control panel to deactivate the washer's lock controls. The lock icon disappears from the LCD control panel when the lock control is off.
Step 2
Push "Start/Pause" to temporarily halt the washer's current cycle, and wait for the indicator light below "Pause" to light up.
Step 3
Lift open the washer's lid or pull the front-loading washer's door open to retrieve clothing in the washer.
Step 4
Shut the washer's lid or door to securely close it, and push "Start/Pause" to resume the cycle.
Step 5
Press "Cycle Signal" until the lock image appears on the front-loading washer's LCD control panel to reactivate the lock control.
