John Deere Mower Deck Spindle Bearing Replacement Step 1: Removing M18 Nut With Impact Gun. Secure the blade holder end of the spindle in a vise and remove the lock-nut... Step 2: Remove the Woodruff Key. Using a punch and hammer, carefully drive the woodruff key out of the shaft. It may be... Step ...
How to replace a John Deere mower deck spindle bearing?
John Deere Mower Deck Spindle Bearing Replacement. Step 1: Removing M18 Nut With Impact Gun. Secure the blade holder end of the spindle in a vise and remove the lock-nut using an impact wrench. Once ... Step 2: Remove the Woodruff Key. Step 3: Drive the Shaft Out Using a Puller. Step 4: Using a ...
How do I replace the bearings on the spindle assembly?
You must now dismantle the spindle assembly in order to replace the bearings. Take the spindle to the bench and suspend the casing over the jaws of a vise or similar object. Reinstall the pulley nut a few turns onto the spindle shaft. As shown in the photo, strike the nut with one sharp blow from a small sledge.
How do you install front wheel bearings on a lawn mower?
Press the new bearings into place. Position the top bearing on top of the spindle housing and use a rubber mallet to press it into place so it’s flush. If there is a sleeve that fits over the shaft within the spindle housing, place that into the housing before installing the lower bearing.
Can you repair a spindle on a riding mower deck?
Instead of purchasing a replacement spindle for your riding mower deck, you can repair the spindle for a fraction of the cost by replacing just the worn-out bearings.
How to repair a worn spindle on a deck?
What to do if your bearings break off?
Does a spindle assembly work with any brand?
Can you use a nut on a spindle?
See more
About this website
How do you replace deck spindle bearings?
0:553:20Lawn Tractor Troubleshooting: How to Replace the Spindle BearingYouTubeStart of suggested clipEnd of suggested clipOnce you have the covers removed undo the belt from the pulleys. Next you'll need to flip the mowerMoreOnce you have the covers removed undo the belt from the pulleys. Next you'll need to flip the mower deck over blade side up remove the nut the washer and then the blade from the spindles.
Can you replace bearing in mower spindle?
0:431:44How To Remove Mower Spindle Bearings - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut pulling these bearings out and then putting new uh the same ones into the new spindle tend to beMoreBut pulling these bearings out and then putting new uh the same ones into the new spindle tend to be a lot cheaper than buying a new spindle with new bearings.
How do you remove bearings from a spindle?
0:544:31How to Remove a Wheel Bearing Inner Race in Under 5 MinutesYouTubeStart of suggested clipEnd of suggested clipSo we're gonna do this right to cut most of the way through this a little bit at a time withoutMoreSo we're gonna do this right to cut most of the way through this a little bit at a time without damaging the spindle. And then use a punch to split it. And then it'll come off easily.
How do you take apart a lawn mower spindle?
1:015:58lawn tractor spindle bearing tear down - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe easiest way for me is to take the lawnmower of light put it in the vise over here. And that willMoreThe easiest way for me is to take the lawnmower of light put it in the vise over here. And that will hold the shaft in place.
Can you rebuild mower deck spindles?
Instead of purchasing a replacement spindle for your riding mower deck, you can repair the spindle for a fraction of the cost by replacing just the worn-out bearings.
How do I test my mower deck spindles?
0:282:11Check Mower Deck Spindle Pulley Bearings Exmark Lazer Z S-SeriesYouTubeStart of suggested clipEnd of suggested clipWhere the bearings are getting play. It simply the way that you can check one of these spindleMoreWhere the bearings are getting play. It simply the way that you can check one of these spindle bearings is by grabbing the pulley.
How do you remove a bearing from a shaft without a puller?
2:063:08How to easily remove a tight bearing without a press or special toolYouTubeStart of suggested clipEnd of suggested clipWhen I put it in the oven. And I poured a well on the the pinion nut and the bearing. So that shrunkMoreWhen I put it in the oven. And I poured a well on the the pinion nut and the bearing. So that shrunk it just enough so that there was enough clearance to knock it out easily.
How do you take bearings off?
3:537:04How to EASILY Remove a bearing and easy reinstall - YouTubeYouTubeStart of suggested clipEnd of suggested clipOpen split right open. And it slides right on and off like nothing you'll fight it forever. And if IMoreOpen split right open. And it slides right on and off like nothing you'll fight it forever. And if I would've done defeat.
How do you change the spindle bearings on a Craftsman riding lawn mower?
1:4611:2103 Murray Craftsman Riding Mower Spindle Bearing & Blade ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what you have to do in order to get the spindle lid off just going to right here is after youMoreAnd what you have to do in order to get the spindle lid off just going to right here is after you put a little bit of PB Blaster on it because they get corrosion.
How do you replace a spindle assembly?
2:206:09Craftsman Riding Lawn Mower Spindle Assembly #532192870YouTubeStart of suggested clipEnd of suggested clipWith the bolt removed set the blade aside flip the deck back over use a half-inch socket to unthreadMoreWith the bolt removed set the blade aside flip the deck back over use a half-inch socket to unthread the mounting bolts securing the spindle assembly to the deck. Remove the old assembly.
How do you replace a spindle?
0:4112:33How to Replace a Spindle | Ferris Z3X | - YouTubeYouTubeStart of suggested clipEnd of suggested clipOff you're going to need a half inch wrench to work on your tensioner pulley and i suggest having aMoreOff you're going to need a half inch wrench to work on your tensioner pulley and i suggest having a cheater bar something to make it a little bit easier give you a little bit more leverage.
How do I remove the spindle nut from my mower deck?
4:0514:23How To Replace The Spindle On Your Riding Mower Or Tractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet a rag or even maybe use a piece of 2x4 to prop against it in order to break that loose I believeMoreGet a rag or even maybe use a piece of 2x4 to prop against it in order to break that loose I believe it's seven eighths but I'll go grab that let's find it okay.
Mower deck - Blade bolt removal on spindles | Lawn Mower Forum
Hi troops, I started to change the blades on my Scag Tiger Cub 48" deck today and ran into a problem. even with a 400FTLB impact wrench and the air compressor at max pressure, I couldn't remove the nut on the R/H blade bolt. I had to drill small holes progressively on opposite sides of the nut and took a chisel and hammer to split the nut to remove it.
How To Replace The Spindle On Your Riding Mower (diy)
How To Replace The Spindle On Your Troy Bilt PonyRiding Mower.My Amazon store https://www.amazon.com/shop/survivalonabudgetmadeeasyMy Merchandise Store https...
Ferris Spindle Removal | Lawn Care Forum
I have a Ferris IS1000 that Im trying to remove the spindle for repair. I have removed the 4 bolts from the spindle and have removed the spindle pulley nut and washer. There does not appear to be a set screw for the 1/4 in key. Does anyone have any suggestions on how to remove the pulley? I...
How to drive a new bearing into a spindle?
Place the new bearings into the spindle. They will only go in slightly. Place the old bearing on top of the new one and tap on the old bearing with the mallet to drive the new bearing into the spindle. Do not tap directly onto the new bearing or you will damage it.
How to stop a mower from spinning?
If the bolt spins with the spindle shaft, wedge a piece of wood between the mower deck and the mower blade. This will prevent the shaft from spinning.
How do I remove the deck from a lawn tractor?
Step 1. Place wooden blocks on either side of the mower deck and then lower the deck onto the blocks. Disconnect the rods that hold the deck onto the bottom of the lawn tractor by removing the cotter pins. Pull the drive belt off the pulley on the motor and then slide the deck out from under the lawn tractor. ...
Why does my lawn mower make a squealing noise?
When you turn on your lawnmower and engage the mower deck , at some point you may hear a squealing sound. This sound is most likely the sound of the spindle bearings seizing up. The spindle bearings are the bearings that allow the deck's pulleys to spin.
Can you change spindle bearings on a lawn tractor?
However, before you can change the bearings, you must have knowledge of how to remove your mower deck from your lawn tractor since this process is different for virtually every mower brand and model. Advertisement.
How to get a bearing out of a clip?
You may need to tap the clip around the perimeter with a hammer and punch and even use penetrating oil to get the clip to come out. After the clip is removed, turn the housing over, and just tap the bearing out using a socket or punch. Ask Question.
What to use to drive a shaft out?
If you do not have a puller, or you cannot keep the puller on the housing as the shaft gets pressed further out, you can use an impact socket and a hammer to drive the shaft out. Make sure you use something that is smaller than the threaded end of the shaft, so you do not damage the threads.
How to get woodruff key out of shaft?
It may be easier to lay the shaft horizontally on a hard surface with the woodruff key facing up, then tapping one side of the key into the shaft to get the key to roll out of the concave hole.
Can you pull off a pulley?
Once the nut is removed, you can pull off the pulley assembly. You may need to use a large bearing separator to drive the shaft of the spindle out of the center of the pulley, to avoid distorting the pulley. Do not hit the bottom of the pulley with a hammer, you will bend it. Ask Question.
How often should I replace $4 bearings?
if you want to look at it close you can pry off and pop out the plastic seal to expose the bearings so the grease fitting can lube them but to be honest its easier to just replace the $4 sealed bearings every 4-5 years. S.
Do I grease the deck spindle bearings on a 2007 Cub Cadet?
I had never greased the deck spindle bearings on my 2007 Cub Cadet. Needless to say, they finally gave out last summer. They were still intact, but they were loud as heck. I didn't realize how bad they were until I replaced them. The ones I replaced them with have grease fittings and they work. THat is how I initially filled them before putting them on the deck. I will be sure to grease the every spring going forward now. The mower is so much quieter now when I engage the deck than it used to be. I don't know how I put up with it.
How to repair a worn spindle on a deck?
Remove the blade and the pulley from the worn spindle. You may want to repair both spindles even though only one is showing symptoms. Remove the worn spindle from the deck. Be careful when removing the bolts. Use penetrating oil and let it soak. If the bolts break off, don't panic.
What to do if your bearings break off?
If the bolts break off, don't panic. You can drill and tap new mounting holes slightly offset from the original ones. You must now dismantle the spindle assembly in order to replace the bearings. Take the spindle to the bench and suspend the casing over the jaws of a vise or similar object.
Does a spindle assembly work with any brand?
Community Answer. Yes, it should work with any brand. The spindle assembly is a fairly common build. It has been used for years by every major brand. Only in a few odd cases will there be a different construction, and in those cases, the best solution will be to replace the entire assembly.
Can you use a nut on a spindle?
Another option is to use the nut for the spindle. With time and patience you can work the nut back and forth to repair the threads. Your best possible option is to use a tap and die set to re-thread the shaft. These can be purchased from most hardware stores (Lowe's, Home Depot, Menard's, Harbor Freight).