2, Pour 2.5 litres of Saniflo Descaler down in to the toilet bowl, if you have a larger Saniflo like Saniplus, Sanipro, Sanibest Pro, we recommend pouring the whole 5 litres down in to the toilet. 3, Leave to stand in the Saniflo Macerator for up to two hours for best results.
How do I Clean my saniflo Macerator?
Once the macerator has stopped pumping, flush the toilet once, wait for the Macerator to stop, then flush once more. This rinses the Saniflo Macerator out and all the remains debris, that’s it your done. 5, Important, do not leave Saniflo Descaler in overnight (As some websites suggest) as it can damage your machine completely.
How much water does it take to clean the sanivite?
Firstly, note that the Sanivite leaves a pint or so of water when it "empties". It will then need about nine pints added to fill it enough to clean the mechanisms.
How do you clean a sanivite dishwasher?
On a regular basis (every three to six months), switch off the unit and then pour about 9 pints of hot water into your sink and mix in some bleach or vinegar or wasing soda (soda crystals). Let this run into the Sanivite and sit there for a while.
Can I use saniflo descaler cleanser on my sanivite?
Secondly, note that the advice in the following paragraph is probably not appropriate if your Sanivite feeds out into a septic tank - but the Saniflo Descaler Cleanser, mentioned in the paragraph after, is claimed to be OK to use.
Why switch off sanivites?
What is a sanishower?
How to undo Jubilee clips?
When to block off the outflow?
Does YouTube cover Sanivite?
Can you use vinegar in a Macerator toilet?
White Vinegar, as in regular household, kitchen variety. Vinegar will do the job without harming rubber seals. It will easily descale most lime build ups. You should likely mix with plain water in a 25x75 mix, depending on how much you intend to use.
What is a Sanivite 3?
Saniflo Sanivite+ 3 Use 32mm discharge pipe. Sanivite – waste water pump for a dishwasher, washing machine, tumble dryer and sink in a kitchen or utility room. Sanivite makes the addition of a domestic kitchen or utility room easy even when below or distant from a drain.
How do I install Sanivite?
0:5313:19Saniflo Sanivite Drain Pump, Unboxing and Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipHas a check valve built into it already. So you don't need to have an extra check valve up topMoreHas a check valve built into it already. So you don't need to have an extra check valve up top really screw things over but you can do it half. You can do two inch it's a nice little plug.
How do you drain a Sanivite?
0:030:29Sanivite drain pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipEveryone will love it Santa Flo install a kitchen anywhere. You want.MoreEveryone will love it Santa Flo install a kitchen anywhere. You want.
Why does my Saniflo toilet smell?
Why does my Saniflo smell? Bad smells can be due to a build-up of limescale and human waste in the 2-3 inches of water that's always left in the Saniflo. To see if it's your Sanilfo that's emitting the bad smell, flush your toilet or fill your basin with water and then unplug it.
How do you use saniflo descaler cleanser?
Easy to Use.Pour half the bottle, or approximately 2.5 liters, of the descaling solution into the toilet bowl.Leave the solution for at least two hours.Connect the unit to the power supply. Flush the toilet a few times.
How does a Sanivite work?
The inside of the Sanivite is comprised of a pressure chamber, which starts and stops the unit, and the motor, which drives the pump. When the water enters the Sanivite, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure.
Where is the microswitch on a saniflo?
This micro switch is located in the pressure chamber inside your macerator unit.
What is a Sanivite?
Sanivite is a powerful pump with four inlets for connection to sinks or appliances. Waste water is pumped through 32mm small-bore pipework, vertically up to 5 metres or horizontally up to 50 metres or a lesser combination of both.
How do you install a Saniswift pump?
3:2210:15How to install a Saniflo - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlways run any horizontal discharge pipe on a minimum. 1 in 100. Fall. This may involve taking upMoreAlways run any horizontal discharge pipe on a minimum. 1 in 100. Fall. This may involve taking up floorboards and notching into the joists or fixing the pipe on a fall along the joist.
Can you run a washing machine through a saniflo?
If your Saniflo system is connected to a washing machine or dishwasher, steer clear of using the 90 degree hot wash cycle. This can cause the motor to overheat and cut out mid-cycle while emptying. Once it has cooled down, the motor will restart. However, it's best to avoid using hot wash cycles where possible.
How far can a saniflo pump?
The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall).
Spares and Parts - PUMP & WATER SYSTEMS
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website.
What is a Sanivite drain pump?
The Sanivite model was designed to sustain the toughest applications meant for drain pumps. Its pumping capabilities and unique design are the reason why these range of pumps are preferred for heavy duty applications.
How does a Sanivite motor work?
When the water enters the Sanivite, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum.
How far does a sanitary sewer pump go?
Water enters the chamber and is pumped away into the sanitary sewer. The unit pumps the effluent upward to 16 feet and/or 150 feet horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again.
Can a Sanivite washer take gray water?
The Sanivite can also accept gray water from a washing machine through an indirect connection such as a laundry sink.
Can a Sanivite drain pump be connected to a GFI?
It is also highly recommended for the drain pump to be connected to a Ground Fault Interrupter (GFI) circuit. The Sanivite is small enough to fit comfortably inside a kitchen cabinet or vanity or inside the overhang of a whirlpool. The Sanivite has been certified to American and Canadian Standards.
What is Saniflo descaler?
Saniflo have developed a special cleaning fluid called Saniflo Descaler and has been specially formulated to clean Saniflo. Macerator pumps. Do Not use any other cleaning products that have not been designed to Saniflo Macerator pumps or you void your guarantee if you have one.
Can you clean a Saniflo pump?
Cleaning a Saniflo Macerator pump is so easy, this work needs to be carried out regular to avoid stop start issues in the near future.
Does Saniflo descaler work on macerator pumps?
The links to Saniflo descaler below will work on most macerator pumps, always read the label!
How to clean a Saniflo toilet?
2, Pour 2.5 litres of Saniflo Descaler down in to the toilet bowl, if you have a larger Saniflo like Saniplus, Sanipro, Sanibest Pro, we recommend pouring the whole 5 litres down in to the toilet. ...
What happens if you don't descale a Saniflo?
If you do not descale your Saniflo as recommended at some point the machine can fail to start or fails to stop or work intermittently , regular use of Saniflo Descaler will prevent this from happening.
How long to stand in Saniflo mizer?
3, Leave to stand in the Saniflo Macerator for up to two hours for best results.
Can you leave Saniflo descaler in overnight?
5, Important, do not leave Saniflo Descaler in overnight (As some websites suggest) as it can damage your machine completely. Leaving the descaler in overnight can destroy and otherwise good machine, even the Saniflo Descaler instructions on the back of the bottle say the chemical should only be in the machine for a maximum of two hours.
Is a Saniflo water softener immune to scale?
Even if you have a water softener you are not immune from scale in a Saniflo, a macerator pump is a human waste machine and needs cleaning regularly.
How to clean Saniflo toilet?
To clean your Saniflo thoroughly, follow the below steps: Turn off the power to the unit. Pour a dose of descaler into the pan. Flush the toilet. Leave for 1-2 hours. Turn on the power and let the unit pump out. Flush again. Simple and straightforward. Plus, you don’t even have to get your hands dirty.
What to do if Saniflo stops working?
Saniflo systems, while easy to install, can be tricky to fix. So, if you find that your Saniflo has stopped working, call out an expert rather than trying to diagnose the issue yourself. You may just end up making the problem worse or even cause damage to yourself or your property.
How to protect Saniflo?
Protect your Saniflo macerator by only allowing waste and toilet paper through the system. Anything else will inevitably cause a blockage, which can lead to easily avoidable repairs. Educate your household on what not to flush. For advice on what to do with a blocked toilet, visit our blog.
How to extend the life of a Saniflo system?
Regular maintenance can help lengthen the life of your Saniflo system. Saniflo approved contractors can arrange a visit to your property and carry out routine maintenance to ensure your system is in perfect working condition. Additionally, if a part needs replacing, Saniflo engineers will be able to fit it for you.
Where can I find Saniflo installers?
You can find a list of approved Saniflo installers on the Saniflo website. If you’re based anywhere in Dorset, Hampshire, Wiltshire, West Sussex or Somerset, don’t hesitate to contact Sani Solutions, approved Saniflo installers for the South of England. #3. Clean your Saniflo.
Can you use hot water in a Saniflo washer?
However, it’s best to avoid using hot wash cycles where possible. Similarly, if you’re using boiling or extremely hot water in your sink, let it cool before emptying it so as not to overheat the system. For advice and support on your Saniflo system, call the experts at Sani Solutions.
Who can help with Saniflo?
For advice and support on your Saniflo system, call the experts at Sani Solutions. We’ve got over 20 years of experience, plus a friendly manner and unmatched customer service. Get in touch today.
Why switch off sanivites?
If you have multiple Sanivites sharing the outflow pipework then switch them off as well to prevent them pumping water back down the pipe to the unit you're working on.
What is a sanishower?
The Sanishower is a differently-arranged and smaller unit with only two inlets, but has some parts in common with the Sanivite and so this page may help. If you are only trying to deal with a smell or noise, or just want to thoroughly clean a Sanivite 3, then start with the section "And in future...". below.
How to undo Jubilee clips?
Now undo the Jubilee clips (28, 30, 30c) and / or plastic clips (30a, 30b) on the various connections. The plastic clips (if yours has that sort) can be released by pushing the two ends apart sideways with pliers, etc. If these break you can replace them with the same size in Jubilee clips - available at most hardware stores.
When to block off the outflow?
Block off the outflow after the pipes have joined together.
Does YouTube cover Sanivite?
YouTube only seemed to cover installation of the Sanivite when I last looked, but this guide to the "Haushaltspumpe" does include a cut-away view of the Sanivite at the start.
