By cutting into your service line and slipping on a compression tee, you can connect your sprinkler system to the water supply without soldering. In some instances, you can avoid cutting the main line by attaching your system to the outside faucet connection (see diagram and note). PVC pipe may be substituted for copper in non-freezing areas.
How do you install a water sprinkler system?
- Plan out where the hoses will go.
- Mark all plants that will need to be watered.
- Each plant should have its own emitter or drip. Note how far apart the plants are. ...
- Each hose will be attached to the water source through a network of drip irrigation lines. These lines will run from the main hose to your plants.
How do you make a homemade sprinkler system?
Instructions
- Begin by gluing the longer ends to the cross-section. ...
- Glue the shorter pieces across from each other using the same method as before into the cross-section.
- On one of the short pipes glue on a threaded cap using the same glue method.
How to install Underground sprinklers?
To purchase the right components, you’ll also have to determine your own specific:
- Determining Water Pressure. Water pressure is measured in pounds per area unit or psi. ...
- Determining Water Meter Size. Start at the meter. ...
- Install the Valve Manifold. Dig a hole slightly larger than the valve manifold box. ...
- Run the PVC Pipe. Connect 3/4″ PVC pipe to the open end of the valve manifold. ...
- Install the Sprinkler Heads. ...
- Install the Controller. ...
How to install underground sprinkler pipe?
- Cut the pipe ends square using a hacksaw or preferably, a PVC pipe cutter. ...
- Insert the pipe end about 1/4″ into the end of the fitting to check the fit, then pull it back apart. ...
- This step is optional, many people don’t use primer. ...
- Coat the outside of the pipe and the inside mating surfaces of the fitting with PVC cement. ...
How do you hook up a sprinkler to a water hose?
0:433:26Attaching garden or hose sprinkler into an irrigation sprinkler system.YouTubeStart of suggested clipEnd of suggested clipYou just slice rifled after's flex five adapters are really easy push them in a little bit and thenMoreYou just slice rifled after's flex five adapters are really easy push them in a little bit and then you just screw them the rest of the way in adds are threaded.
How do you tap into an existing water line?
To tap into existing copper lines, shut off the water. With a tubing cutter cut an opening in each pipe that is about an inch shorter than a tee fitting. Dry-fit the tees. If the pipes are rigidly installed, remove a clamp or two so you can pull the pieces apart slightly.
Are sprinklers connected to plumbing?
A new sprinkler system will need to be connected to your home's cold water supply. If existing pipes will need to be cut, you may want to hire a plumber; otherwise, don't forget to turn off the water before you get to work. If you live in a mild climate, you only need an outdoor faucet to connect to.
Can you run a sprinkler system off a spigot?
While many commercial sprinkler systems tap directly into the water service line of your house, you also can connect your system to an outside faucet.
How do you tap into an existing PVC water line?
0:042:17How to Tie Into an Existing PVC Plumbing Pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor this job we'll be using a battery-powered saw our glue and primer and a marker so if you'reMoreFor this job we'll be using a battery-powered saw our glue and primer and a marker so if you're wanting to tie in with a tea to your pipes. You'll take the tea. Place it over the pipe.
How do you connect PVC pipe to outside water faucet?
Steps to Connect Outside Water Faucet to PVC PipeRemove the Existing Hose Bibb. The first step is to remove the existing hose bibb from the outside faucet. ... Slip PVC Pipe Over the End Of Faucet. ... Secure With Clamps. ... Connect Ends to Threaded Connectors. ... Tighten Everything Down.
Where do sprinklers get water from?
Pump systems pump water into the sprinkler from a body of water, like a lake or a pond. This allows homeowners to service their system without taking on additional water costs. Metered water systems are usually tied to the home's existing water lines and are serviced by the local utility department.
Where is main sprinkler valve located?
0:152:13How to Find Your Sprinkler System Shut-Off Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsually in the basement or in a utility room starting at the floor.MoreUsually in the basement or in a utility room starting at the floor.
Where does fire sprinkler water come from?
Most fire sprinkler systems are supplied from a municipal water source, but water supplies can also be provided by water storage tanks or natural sources such as lakes or ponds.
How do you connect a spigot to an irrigation system?
0:052:39How to Install a DIY Drip Irrigation System to your Hose Faucet: RaindripYouTubeStart of suggested clipEnd of suggested clipSystem you just connect the white connector. Then twist on the timer. Make sure that the arrow onMoreSystem you just connect the white connector. Then twist on the timer. Make sure that the arrow on the timer is pointed out because that's the direction of the water flow. Next connect your supplied.
How many sprinklers can you have on one spigot?
The best set-up is to run two hoses from the spigot–each to one sprinkler.
Can I connect a hose to a sprinkler head?
Are you attempting to attach the garden hose to the disconnected sprinkler head or to the sprinkler system where the head was removed? It is highly likely the answer to both is yes as the sprinkler systems use standard fittings.
How do I install an above-ground sprinkler system?
2:069:47DIY above ground Sprinkler System...NO DIGGING!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere we have the hunter pro-spray in-ground sprinkler head. And what we do is we connect it to aMoreHere we have the hunter pro-spray in-ground sprinkler head. And what we do is we connect it to a lawn spike that has 1/2 inch hose connectors. And then you take this MP rotator.
What is a combination sprinkler system?
20.3 of the 2019 edition of NFPA 14: Standard for the Installation of Standpipes and Hose Systems defines a combined system as: A standpipe system that supplies both hose connections and automatic sprinklers.
How do you connect a hose bib to an irrigation system?
1:063:25Adding a Hose Bibb to an Irrigation System - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe proper tool for the job to finish this end of the pipe line I just assemble to dielectric UnionMoreThe proper tool for the job to finish this end of the pipe line I just assemble to dielectric Union and tighten it up then I replaced the top section of the hose bib riser.
Prepare for Your Sprinkler System
Living landscapes need water to survive and flourish, but relying completely on natural rainfall isn't always a reliable way to supply water. An underground sprinkler system offers the convenience of spraying water directly where it needs to go and the opportunity to automate your watering schedule according to your needs.
Determine the Water Pressure
There are two measurements of water pressure: working (when the water supply is turned on) and static (when the water supply is shut off). You'll need a pressure gauge to determine your working water pressure number. The gauge attaches to the outside faucet and provides a pressure reading in PSI.
Determine the Water Meter Size
If you're on a municipal water system, you should find the size printed on the meter itself. If you can't locate it, look on your utility bill or call your water provider. Water meters are 5/8 inch, 3/4 inch or 1 inch.
Determine the Service Line Size
To match the size of the irrigation pipe to your existing water service, you'll need to determine the size of your incoming supply line. To do so, get a piece of string and wrap it once around the water pipe. Measure the length and compare it to the chart below.
Map the Sprinkler System
When you've completed all of the preliminary research, it's time to start laying out your system. Most yards have a variety of elements that have to be considered when laying out an irrigation system:
Plan the Coverage
When installing a sprinkler system, 100% coverage is essential to avoid dry spots. You can achieve this by overlapping the spray pattern. Head-to-head coverage refers to the sprinkler head layout that allows spray from each sprinkler head to reach the adjacent head, ensuring overlap.
Know the Primary Parts
Done with the planning? Take your water measurements and maps with you when shopping for parts. You'll need to select your system components to match your water supply and water pressure. A mismatch will either stress the system or provide insufficient irrigation.
Connecting at The Main Supply Line
- Make sure to turn off the water before the location where you plan to cut into the pipe. To make a connection aboveground, cut out a short piece of pipe in the supply line, install a slip tee, and attach a nipple to the stem for the shutoff valve.
Preventing Backflow
- It’s important to prevent debris from washing back into your water supply when you attach a sprinkler system to the main line. Backflow preventers come installed into anti-siphon control valves. Use a vacuum breaker at the start of the system if you’re using in-line valves, or put one on the end of the faucet if you’re installing a single-circuit system that connects to the hose bibb…
Connecting to Other Water Sources
- You can use water from a well, pond, or stream for your irrigation system the same way homes connect to city water. The first thing you need to do is determine the water pressure and flow rate. To find a well source’s water pressure, simply place a pressure gauge on the wellhead pipe. Most sprinkler systems need between 30 and 50 pounds per square inch to operate efficiently; if you …