iAquaLink Setup
- Confirm that the internet connection switch on the iAquaLink is set to the wired position
- Connect the ethernet cable into the ethernet port on the iAquaLink
- Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected.
Can the iaqualink Web Connect device be used in addition to Aqualink?
The iAquaLink Web Connect Device can be used in addition to an existing AquaLink RS control system, however, the firmware, in the power center must be updated to revision R or later.
How do I connect to the AquaLink power center?
Ensure all power to the AquaLink power center is off. With the dead front panel removed, feed the red 4-pin connector through the bottom access hole into the low-voltage raceway.
How does the Jandy Aqualink app work?
How it Works The iAquaLink app lets you monitor and adjust all equipment controlled by the Jandy AquaLink pool control system. First, your equipment is wired to an AquaLink control center, which is installed at your equipment pad. Then an iAquaLink 3.0 Web Connect Device is connected to the control center.
What can I do with Aqualink?
Check the status of pumps, pool & spa lights, temperatures, and even change the temperature set points. Depending on the AquaLink you are controlling, it can even be used to control solar heating systems, water features such as waterfalls, water jets, spill-overs, and more.
Why is my Aqualink not connecting?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
How do I change the WiFi on my Aqualink?
Inside the iAquaLink 2.0, toggle the WiFi - Wired switch to clear the Wi-Fi settings and put the iAquaLink in desired setup mode. 3. After clearing the WiFi settings and with the Wired/ WiFi switch set to WiFi, use a smartphone or WiFi enabled device and go to WiFi settings.
How do I connect my iAquaLink to a new router?
2:586:47iAquaLink 2.0 installation video - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release theMoreAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release the WPS. Button and wait for the small yellow LED next to the WPS button to begin blinking.
How do I fix iAquaLink waiting for connection?
0:402:09How To Fix "Waiting For Connection" For Jandy iAqualink AutomationYouTubeStart of suggested clipEnd of suggested clipLet us sit there for a second good five seconds or so and then go ahead and plug it back in and thenMoreLet us sit there for a second good five seconds or so and then go ahead and plug it back in and then from there you should be able to have. Your phone connects to your automation.
How do I reset my Jandy AquaLink?
How do I Reset a Jandy AquaLink System?Press the "Menu" button.Scroll to and highlight "System Setup" using the arrow keys. Press "Enter."Scroll to highlight "Clear Memory," then press "Enter." You have now reset your AquaLink system.
How do I program my Jandy AquaLink?
Basic Programming: To set a particular piece of equipment to turn on and off at a predetermined time, press the MENU button, press the forward arrow button to scroll to the PROGRAM menu, press ENTER, and then press the button for the equipment that you want to program.
How do I connect my iAquaLink iq900 to WiFi?
Remove the gasket and cover. Locate the WiFi/WIRED switch and ensure it is in the WIRED position. Using standard Ethernet cable, connect one end of the cable into the connector on the device board. Connect the other end to the home network's router.
How do I reset my iAquaLink password?
Note that if you have an invalid or non-working email address, you will not be able to reset your password and will need to call our Customer Experience team at (800) 822-7933 to reset your account.
What is iAquaLink?
iAquaLink is a system that includes a device, a web service, and a set of mobile and web apps to allow pool owners and pool professionals easy, convenient control of the pool or pool/spa system, from web-connected devices.
How do I use iAquaLink app?
0:004:00iAqualink Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipLink app on your phone and then you click on web view on the top right it will bring you to thisMoreLink app on your phone and then you click on web view on the top right it will bring you to this very same screen if you click on the status.
How do I update iAquaLink firmware?
If your phone is set to allow updates to be automatically installed, the iAquaLink app will update to the new version automatically. If your phone is set to allow manual updates only, you can download the iAquaLink app at the iOS App or Google Play App stores.
How do I reset my iAquaLink password?
Enter your email address below and we'll send you a link where you can reset your password.
How do I use the iAquaLink app?
0:301:49How iAqualink Works With Your Pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd so to turn the waterfall on you go to devices. And you turn it on. And then the lights are alsoMoreAnd so to turn the waterfall on you go to devices. And you turn it on. And then the lights are also on this device area there's two lights there's the full light. And then there's also a spotlight.
Why choose iAquaLink
You don’t have to visit the pool pad to turn valves or set up pump speeds. Do it all from the app!
Get the iAquaLink app
Download or update the iAquaLink app free from the App Store or Google Play.
How to connect AquaLink power center?
Ensure all power to the AquaLink power center is off. With the dead front panel removed, feed the red 4-pin connector through the bottom access hole into the low-voltage raceway.
Who installs iAquaLink?
The device needs be installed by a licensed electrician or qualified pool professional. They can provide you with an installation estimate or quote.
What is the best pool controller for Android?
Swimming pool automation from your mobile phone, tablet, or web-connected device. Zodiac iAquaLink is the most intuitive and user-friendly mobile pool controller for iOS and Android.
How to contact Fluidra iAquaLink 2.0?
iAquaLink 2.0 Support. If you need assistance, please submit an online request, call (800) 822-7933, or e-mail us at [email protected]. iAquaLink 2.0 SSID/Set-up. Welcome, and thank you for purchasing the iAquaLink 2.0!
How to connect a PC board to a metal brace?
Pull the connector between the PC board & the metal brace, and connect it to the red 4-pin socket as shown.
What languages does iAquaLink support?
iAquaLink currently supports English, French, Spanish, German, Italian, Portuguese, Dutch, Swedish, Russian, and Afrikaans with more to come in the future. In addition, the iAquaLink apps will detect the language used on the smart phone or tablet, and use that language as the default.
Is AquaLink compatible with Jandy?
Installation options are available for virtually any Zodiac or Jandy® branded AquaLink® Automation system ever made. iAquaLink is not compatible with other manufacturer's automation systems, but for many other automation systems, AquaLink conversion kits are available.
What is iAquaLink?
iAquaLink is a remote pool control system that allows you to control temperature, pumps, filters, lights etc for your pool and spa systems.
How long does it take for the yellow LED to stop blinking on an iAquaLink?
Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected. WiFi Setup (iAquaLink 2.0 and greater): WiFi setup requires connecting via hotspot on your cell phone.
What happens if iAquaLink fails?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
What does it mean when the iAquaLink LED turns green?
If the iAquaLink LED turns green, it’s successfully connected to the WiFi. After clearing the WiFi settings, by physically toggling the WiFi-Wired switch to Wired then back to Wi-Fi, use a smartphone or WiFi enabled device to go to WiFi settings and connect to the network labeled "iAquaLink".
Does iAquaLink detect network strength?
iAquaLink will display the networks it detects, as well as signal strength. Select the network iAquaLink should use. If prompted for a password, enter the password for the home network (case sensitive). iAquaLink will disconnect from the smartphone at this point.
How to connect iAquaLink J box to internet?
Remove the gasket and cover. Locate the WiFi/Wired switch and ensure it is in the WiFi position. Using a USB cable, connect the iAquaLink J-Box to an internet enabled computer. Download the WiFi Set-up tool below and follow the directions. iAquaLink WiFi Setup Tool 1.2.1 for Mac OS X 10.6+
What is iAqualink app?
What is iAqualink? iAquaLink is a system: a device, a web service, and a set of mobile and web apps to allow pool owners easy and convenient control of their pool or inground pool/spa system, from their smart phone, tablet, computer, or web-connected device, any time, virtually anywhere.
What languages does iAquaLink support?
iAquaLink currently supports English, French, Spanish, German, Italian, Portuguese, Dutch, Swedish, Russian and Afrikaneer with more to come in the future. In addition, the iAquaLink apps will detect the language used on the smart phone or tablet, and use that language as the default.
How to improve signal strength?
If signal strength is weak, there are several ways to improve it: If there are existing wired controllers in the house, you can connect the Web Connect Device to the 4-wire cable used for the controller. This can serve to locate the device indoors, closer to the router (availability depending on countries).
How does a pool device work?
The device can be mounted indoors or out , depending on specific site requirements as determined by a pool professional. Once installed, the device connects to the internet, via the pool-owners router. The device can be connected to the router using a WiFi (wireless) or Ethernet (wired) connection.
How to change pool location on pool app?
To change the pool being controlled, just touch the settings tab and select the location you wish to control. It doesn't get any easier.
How to contact Fluidra iQ900?
United States Spanish. iAquaLink iQ900 Support. If you need assistance, please submit an online request, call (800) 822-7933, or e-mail us at [email protected]. iAquaLink SSID/Set-up. Welcome, and thank you for purchasing iAquaLink!
How to connect AquaLink power center?
Ensure all power to the AquaLink power center is off. With the dead front panel removed, feed the red 4-pin connector through the bottom access hole into the low-voltage raceway.
Who installs iAquaLink?
The device needs be installed by a licensed electrician or qualified pool professional. They can provide you with an installation estimate or quote.
What type of cable is used for IQ30?
When using CAT5 or CAT6 Ethernet cable to connect to a wired network, it is required to use a Ferrite bead as the wire comes out of the IQ30 device. Contact Zodiac Pool Systems LLC Customer Service for a Ferrite Kit (PN#R0914600) free of charge. Wrap the Ethernet cable three turns around the Ferrite bead and connect the short run of cable into the IQ30 RJ45 connector. Connect the other end of the Ethernet cable to the home network’s router.
What is the best pool controller for Android?
Swimming pool automation from your mobile phone, tablet, or web-connected device. Zodiac iAquaLink is the most intuitive and user-friendly mobile pool controller for iOS and Android.
How to contact Fluidra iAquaLink 3.0?
iAquaLink 3.0 Support. If you need assistance, please submit an online request, call (800) 822-7933, or e-mail us at [email protected]. iAquaLink 3.0 SSID/Set-up. Welcome, and thank you for purchasing the iAquaLink 3.0!
What languages does iAquaLink support?
iAquaLink currently supports English, French, Spanish, German, Italian, Portuguese, Dutch, Swedish, Russian, and Afrikaans with more to come in the future. In addition, the iAquaLink apps will detect the language used on the smart phone or tablet, and use that language as the default.
What is iAquaLink?
iAquaLink is a system that includes a device, a web service, and a set of mobile and web apps to allow pool owners and pool professionals easy, convenient control of the pool or pool/spa system, from web-connected devices. iAquaLink 3.0, iAqualink 2.0 and the first generation iAquaLink provide the same end-user experience.
What firmware is used for AquaLink?
For use with AquaLink®RS for Systems with Rev R Firmware or later For use with PDA for Systems with 6.0 Firmware or later
How far away from motor is iAquaLink J box?
Mount the outdoor iAquaLink J-box at least six (6) feet (1,8 m) above the ground, at least eight (8) feet (2,4 m) from any motor or air blowers that may be in the vicinity, and at least five (5) feet (1,5 m) away from other transceiver J-boxes. See Figure 3.
How far away from the water should a power center be from a pool?
Risk of electric shock - Install the power center at least five (5) feet (1,52m) from the inside wall of the pool and/ or hot tub using non-metallic plumbing. Canadian installations must be at least three (3) meters from the water. Children should not use spas or hot tubs without adult supervision. Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment. People using medications and/or having an adverse medical history should consult a physician before using a spa or hot tub.
Can you remove the suction fittings on a spa?
To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the equipment assembly.
Is iAquaLink pre-configured?
The iAquaLink Web Connect Device is pre-configured at the factory for WiFi connection. If using wired connection skip to Section 4.4.
