- Shut off power at the breaker. Remove motor from pump housing. ...
- Remove pump diffuser. Hold shaft at rear of motor with pliers/wrench, and spin impeller off shaft, counter-clockwise.
- Lubricate 4 through-bolts with WD-40. ...
- Use a flathead screw driver and small hammer to loosen and pry off the front end bell .
How to troubleshoot a pool pump motor?
The number one test when looking for a motor problem is to check the incoming AC power right at the motor connections. If you have AC power, and the pump is not working, then it has to be something in the motor. Keep in mind that if your system uses 240 VAC, than you must measure between the L1 connection and the L2 connection.. You can get an error if you try to measure L1 to ground and then L2 to ground.
How to empty a pool without a pump?
How to Empty a Pool Without a Pump
- Place one end of a water hose in the pool. Push it down so it is near the bottom of the pool.
- Take the other end of the hose to where you want the water to drain. ...
- Siphon the water out of the pool by placing your mouth on the end of the hose and sucking repeatedly until water comes out.
How to replace pool pump?
How to Replace an In-Ground Pool Pump
- Turn off Power to Pump. It is important to turn the power off to the pump and filter before removing it. ...
- Stop Water Flow From Pool. To remove the old inground pool pump you will need to stop the flow of water from the pool to the pump.
- Disconnect Hoses from Pump. ...
- Disconnect Pump from Filter. ...
- Remove and Replace Pump. ...
- Connect Pump to Filter. ...
How to clean out and unclog a pool pump impeller?
How to Unclog the Impeller
- Turn the pump off. I prefer turning the breaker off since you definitely do not want the pump turning on while doing this.
- Insert a long screwdriver into the pump as shown in the photo. ...
- If the impeller is clogged, it will be a bit difficult to move at first. Work the impeller both ways until it begins to move more freely. ...
How do you turn off a pool motor?
0:172:26How To Turn Power Off To Your Pool - Pool Troopers - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the non shot card is intact. When you're sure you're on dry ground and the non shot cardMoreMake sure the non shot card is intact. When you're sure you're on dry ground and the non shot card is intact. Go ahead and turn the timer off. You should hear an audible click.
Do you disconnect pool pump in the winter?
PRO of Disconnection Keeping pumps away from accumulating moisture (assuming you live in a place that gets considerable rain/snowfall) during the winter is a good way to protect the equipment. Heavy snow is a danger to pool equipment that remains outdoors.
How do I turn off my Hayward pump?
0:072:02How to shut down pump and clean pump basket - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you have if you don't have an easy toss chances are you have a mechanical timer. And there's justMoreIf you have if you don't have an easy toss chances are you have a mechanical timer. And there's just a non open that up and there's an on/off switch in that.
Is it OK to turn pool pump off?
There is no need to turn off your circulation system during a rain storm. We need the chemicals to still work and want the dirt and debris to be filtered out just like under normal circumstances. Never try to change settings on the pool pump or at the timer when it is raining.
At what temp will pool pump freeze?
If you have an above ground pool with the pool filter system and plumbing above ground (like nearly all above ground pools), pipes and pumps can freeze up in less than an hour of minus 32 degrees. The same is true for inground pool equipment that is not running when temperatures are below freezing.
What do I do with my pool pump in the winter?
6:408:02How To Keep Your POOL Open All WINTER (Follow These ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipLevel make sure that your pool's water level is at least halfway up the skimmer. So your pump andMoreLevel make sure that your pool's water level is at least halfway up the skimmer. So your pump and filter can run without sucking in air now what happens if your pump accidentally shuts off in the
Why is my pool pump not turning off?
PUMP WON'T TURN OFF You can rotate the dial, or shut off the pump with the breaker. Does the timeclock dial spin, and keeping correct time? It may be bent, or not engaging the gear behind the timer dial. If you have just a switch, and not a timeclock, the pump not shutting off would be a faulty or mis-wired switch.
What happens if pool pump runs without water?
Swimming pool pumps should never operate without water. They will overheat and cause excess damage. Running a pump without water can also warp the lid, basket and the adjacent plumbing. If the pump continues to run without water, there is a high possibility of causing damage to the plate, seal and bearings.
How do you turn on a Hayward pool pump?
How to Operate a Hayward Pool PumpEnsure the hoses are securely attached. ... Check the skimmer water level. ... Add water to the pump basket. ... Open the air valve. ... Confirm that the necessary cleaning agent is in the filter. ... Monitor the filter's pressure gauge and water return flow.
How long can a pool pump be turned off?
This is the how many minutes your pump has to filter to get full turnover. For most pools, it's going to be about eight hours.
Is it OK to leave pool pump off for a week?
So if you have to leave it running for a week it shouldn't make a big dent in the electric bill. Having to spend the money on getting the pool back in shape will probably cost more than leaving it on anyway. I would make sure you fill the pool water as high as you can though since you will be gone for a week.
Can I turn off my swimming pool pump at night?
It may be cheaper to run the pump at night, but honestly you should run it 1 hour a day per 10 degrees of temperature at least, and it should be during the day. Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up.
Can you leave a pool pump and filter outside in the winter?
Even if your filter itself doesn't crack, leaving it outdoors for the winter could cause premature wear and tear. Chances are that if you've already picked out the right filter for you, you know they don't come cheap. Make sure you take care of yours by winterizing it properly and storing it away in a safe, dry place.
How do you turn off a pool pump for the winter?
1:504:25How To Winterize A Pool 3 - Pool Pumps - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt and sometimes they have winterization ports similar to in-ground pool pumps but usually not youMoreIt and sometimes they have winterization ports similar to in-ground pool pumps but usually not you usually you just take an above-ground pool pump you disconnect it electrically by unplugging it.
How do I turn off my pool filter for the winter?
After a backwash and rinse, place the valve to the “winterize” setting on the top mount valve. This will allow water to drain from the valve. Next, you're going to have to completely drain all the water from the filter tank. To do this simply unscrew and remove the drain cap on the bottom of the filter barrel.
Should I run pool pump when freezing?
Tips To Keep Your Pool and Equipment Safe During Freezing Temperatures. Run your pool pump continuously when temperatures are near or below freezing. You don't need to run your heater, moving water likely will not freeze. Disconnect any aerators and lines to slides.
How far away from a pump should a disconnect be?
The disconnect is for the pump not the water. The disconnect must not be more than 50' from the pump and within sight of the pump. I stand by my original statement.
How far away from pump should a cb be?
As long as the cb is within sight and 50' or less from the pump then you are good. No need to lock the panel.
Can an emergency cutoff be the same as a disconnect?
All that mike is saying is that the emergency cutoff can be the same as the disconnect for the motor if it is within sight of the motor. The only difference would be that an emo switch would have to be labeled. It is kind of ridiculous if the emo switch was 50' away but it seems that is allowed.
Do pool pumps have overload protection?
Not familiar with what is common with pool pumps, but there are general use motors of 10 HP that have internal overload protection, so it is possible the motor can have internal protection, if it does you shouldn't need to provide any other overload protection.
Does redesigning pumping system inlets reduce the need for an emergency off switch?
True, but redesigning of pumping system inlets I believe has also greatly reduced the real need for an emergency off switch. At same time I don't see it being easy to convince a CMP to remove a safety feature from code. The dwelling exception to the rule likely has been there since a time when more common sense approach was taken for code making process.
How to stop pool pump from getting stuck?
You can buy skimmer basket socks or use a pair of pantyhose to line the inside of your pool pump basket to prevent debris from getting stuck.
How to tell if pool pump impeller is stuck?
You can usually tell if your impeller is stuck if your pool’s water flow seems low or if the lid of the pump basket is not filling up with water the way it should. Your impeller is probably also clogged if the filter pressure reads lower than usual and the water in your pool pump is moving in a swirling motion or slowly. Another sign of a pool pump impeller being stuck is if it is making a low, grinding noise, or any other rough sound.
Why do you need two gaskets on a pool pump?
Two gaskets make it easiest for you to remove stubborn pool pump impellers because they slide against each other and help the impeller break loose.
What happens if the impeller is not seated?
Make sure the impeller is fully seated before starting the pump up. If it is not, the impeller will slam against the shaft sleeve may damage it or the impeller .
Why does my pool pump get stuck?
Two of the most common other reasons are that you or someone else put anti-seize on the hub face or only use one or no gasket. Using anti-seize on the gaskets and faces of the shaft sleeve makes these parts more slippery and will cause them to overtighten on the shaft.
What is the basket in the pool pump?
The pool pump basket in front of the impeller is designed to keep debris from clogging it. However, sometimes debris is small enough that it gets through the basket anyways. Anything from grass clippings, pine needles, broken pieces of pool plaster, tiny pieces of dirt or rocks, or even plant stamens from trees can be responsible for a clogged impeller.
Why is my pool pump clogged?
Impellers commonly get clogged in the early spring, when your pool is still closed and the weather starts to change. The wind blows around leaves and twigs that get sucked into your pool pump, clogging the impeller and disrupting the water flow. It’s actually a fairly common pool pump problem. If that’s the case with your equipment, read my full ...
How do I remove a pool pump for winter storage?
There are two ways to go about removing a pool pump for winter storage – you can remove just the motor or you can remove the entire pump and motor. If your pump has union connections on the pipe, before and after the pump, it makes the job much easier. If you don’t have unions, or have no room in the pipes to install unions, then you would remove just the pump motor by either removing 4-6 bolts or the volute clamp band , or the mounting nut used by Jacuzzi. After the pump volute is separated, grab the motor firmly and slide it straight back to separate it from the pump.
How to keep rain out of motor?
With the wir es removed from the motor, twist a electrical nut on the end of each and wrap all the wires tightly with electrical tape, covering the conduit opening also, to keep rain out.
How to stop time clock from turning on?
Make sure that power is OFF at the breaker, by shutting off all the circuit breakers on the sub-panel and also shutting off the time clock. Remove the On Dogs, or timer trippers from the timeclock, to prevent the clock from turning on again if anyone flips the breakers back on during winter.
Can you unplug an above ground pool pump?
Aboveground pumps can simply unplug the cord, and if small enough move the entire pump and filter system inside for the winter. But inground pool pumps are hard wired with a flexible conduit containing two power leads ...
Can you wrap a motor in plastic?
If you keep your motor outdoors all winter, you could build a ‘lean-to’ with lumber or plastic for snow, rain and tree branches, but keep good air flow around the motor, and don’t wrap it in plastic, which traps moisture inside the motor.
Can cold temperatures affect pool motors?
Although cold temperatures likely do little harm to the steel, copper and plastic components of a pool motor, many feel that it can weaken the capacitor, which essentially is a battery. The larger concern is over water – rain and snow, sometimes feet of snow. The armature is sealed up pretty tight on a pool pump, ...
Can you freeze a pool pump in winter?
A quiet debate has circulated among pool service guys for years. Whether or not it’s worth it to remove pumps or more specifically, pump motors, from the equipment pad during winterizaton. Pump motors can develop rust in the tiny air space between the stator and rotor, deep inside the motor, which can freeze up a motor when you try to start it in springtime.
What is maintenance disconnecting?
A. A maintenance disconnecting means is required for the permanently installed pool, storable pool, outdoor spa, outdoor hot tub, or fountain equipment, other than lighting for these water bodies [680.12]. The maintenance disconnecting means must be readily accessible and located within sight and at least 5 ft from the permanently installed pool , ...
What is a building/structure disconnect?
Building/structure disconnecting means for buildings or structures supplied by a feeder or branch circuit, Grounding electrode conductor if of sufficient size, or. Grounding electrode system. This rule doesn’t require the bonding of sheet metal framing members (studs) or the metal skin of a wood frame building.
Does removing the power to the clock motor solve the noise?
I agree with Jim R. that removing the power to the clock motor solves the immediate problem of the noise. But then you have the issue of it being a rental house. The timer not running can confuse renters and even if the switch is labeled emergency cutoff renters will turn it off.
Can a 2 speed pump run on high speed?
2-Speed pump will not run on High Speed from controller. Runs High Speed manually
Can a timer switch be moved to off?
Yes, so when timer manual on/off switch is moved to OFF, the relay (that’s powered off Load from timer 2/4) disengages while also removing power from pump.
Why is my pool pump not pulling water?
When you pool pump is not pulling water, it could be clogged. Or, you could have a pool pump impeller problem where it may not be strong enough to fit the requirements of your pool. Be sure to check the impeller for debris. Anything caught in the impeller will prevent water from pulling through.
Why does my pool pump burn out?
When your pool pump is clogged for an extended period of time, it begins to pull air instead of water, causing the impeller to spin rapidly. This problem is called “loss of prime” and causes the motor to burn out. You’ll need to discuss the damage with a technician to see if the motor must be replaced. On the inside of your pump, there could be ...
How long do pool pumps last?
Your pool pump should be replaced anywhere between 8 to 15 years depending on the quality, and a full replacement may cost over $800.
What is a pool pump made of?
It’s made up of a motor, impeller, and a hair and lint trap with a basket. Often when there’s a problem, you can simply replace one of the mechanisms, such as the motor, without replacing your whole pool pump.
What is variable speed pump?
You may also want to look into what’s called a “variable speed” pump. This type of pump helps reduce the cost of electricity and lessens the load on your motor. It’s required by pool owners in some states to conserve energy. 3.
How long does it take for algae to build up in a pool pump?
When there’s a problem with your pool pump, you’ll notice many immediate issues. Once your pool pump is down for a few days , you’ll quickly notice algae scum building up.
What does it mean when a pump pops?
A loud screech, steady hum, or quick and repetitive pops are all signs there is a serious mechanical issue. These problems all involve the pump’s motor and require a technician to assess if the motor can be saved by replacing individual pieces within the motor instead of replacing it.
