How to Make the Hole Wider in a Porcelain Sink.
- 1. Move the porcelain sink to an outdoor location if possible. Place a plastic bucket under the hole you need to enlarge. Set a water-filled 1-gallon ...
- 2. Fit a rotary tool with a double-fluted tungsten carbide or diamond-tipped non-tapered bur. Make sure the bur locks in place.
- 3. Don a pair of safety goggles, a dust mask and ear protection.
- 4. Remove the nail from the milk container. Adjust the container to point the flow of water at the porcelain sink's hole. Make sure the water flows ...
- 5. Pull the rotary tool's trigger to spin the bur. Keep the tool body and cord out of the water. Align the bur's cutting flute with the hole's edge.
How do you widen a porcelain sink without a drill bit?
Instead, using another tool allows you to widen a porcelain sink's hole without using a drill bit. Move the porcelain sink to an outdoor location if possible. Place a plastic bucket under the hole you need to enlarge. Set a water-filled 1-gallon milk container next to or above the hole, depending on the hole location.
How do you fix a hole in a porcelain sink?
Move the porcelain sink to an outdoor location if possible. Place a plastic bucket under the hole you need to enlarge. Set a water-filled 1-gallon milk container next to or above the hole, depending on the hole location. Puncture the container with an 8d nail at a location that points toward the hole.
How do you remove a nail from a porcelain sink?
Fit a rotary tool with a double-fluted tungsten carbide or diamond-tipped non-tapered bur. Make sure the bur locks in place. Don a pair of safety goggles, a dust mask and ear protection. Remove the nail from the milk container. Adjust the container to point the flow of water at the porcelain sink's hole.
How do you use a bur on a porcelain sink?
Adjust the container to point the flow of water at the porcelain sink's hole. Make sure the water flows into the plastic bucket and not on the floor. Pull the rotary tool's trigger to spin the bur. Keep the tool body and cord out of the water.
How do you widen a porcelain hole?
0:000:41How to widen a hole in porcelain, ceramic, granite or marble sink.YouTubeStart of suggested clipEnd of suggested clipYou will need angle grinder. And diamond coated milling. Bit use that to widen the hole in your sinkMoreYou will need angle grinder. And diamond coated milling. Bit use that to widen the hole in your sink.
How do I put an extra hole in my sink?
You have a sink with extra holes and need to fill the holes with extra accessories. The easiest and most inexpensive way is to order faucet-hole caps to cover and plug the extra sink holes.
Can you drill porcelain sink?
Drilling a Ceramic Porcelain Sink You'll need to use a carbide or diamond-tipped drill bit on your sink as it's the hardest drill tip out there. Using the correct shape of drill bit can also make a difference in terms of both speed and precision. You can then start drilling in your designated spot.
Can you drill an extra hole in a sink?
If you need to add an additional hole, you can drill it on site with a metal hole saw. The hole site is measured and marked on the front of the sink. A punch is used to dent the steel and give the guiding bit of the hole saw a place to rest and steady itself as it drills.
Are all kitchen sink holes the same size?
Depending on your sink or countertop material, holes can be drilled to accommodate an odd-sized faucet or one that does not fit the predrilled holes in your sink. A standard sink faucet hole has a diameter of 1 3/8 inches, but because not all faucets are the same, some will require a 1 1/2-inch hole.
What is the hole in the kitchen sink called?
overflow holeThe overflow hole is aptly named, as it keeps your sink from flooding. It does this by diverting water, giving you more time to act before the contents spill over if you or someone in your household accidentally leaves the faucet on or if you have a plumbing issue.
How do you cut a hole in a ceramic sink?
Place either a ceramic drill bit or a diamond-tipped hole saw into the drill chuck. A ceramic bit is easier to control as it acts much like a regular drill bit. A diamond-tipped hole saw gives you a smoother entry hole when the job is finished.
How do I drill a hole in my enamel sink?
Enamel coatings are less durable and more difficult to drill than other materials, so use finesse when drilling. Choose a drill with a maximum speed near 600 rpm. Drill the pilot hole at medium speed and apply easy pressure at a low speed with the carbide porcelain cutter.
How do you cut a hole in a bathroom sink?
1:213:43How to cut out a countertop for a basin ot sink. Plumbing Tips - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne thing to keep in mind with your jigsaw make sure your blade is long enough so that the strokeMoreOne thing to keep in mind with your jigsaw make sure your blade is long enough so that the stroke stays down at least a half an inch below your countertop.
What is cobalt drill bit?
What are cobalt drill bits? Cobalt bits are a combination of steel (or another alloy) mixed with a small percentage of cobalt, typically between 5 – 7%. Cobalt has a melting point of 1495°C and a boiling point of 2927°C, which makes it perfect for use at high temperatures.
How do you use Rothenberger hole punch?
0:432:07Metal Hole Punch - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut this thing through like this. And go ahead and screw it on. And then you use a wrench to tightenMorePut this thing through like this. And go ahead and screw it on. And then you use a wrench to tighten. This bolt and as I tighten the bolt it draws. This part in closer. And makes the hole.
How do you make a hole in a ceramic sink?
2:076:02How to drill hole in ceramic sink? - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the button to lock lock the drill. Bit the core bit. And then you want to start with that 3000MorePress the button to lock lock the drill. Bit the core bit. And then you want to start with that 3000 rpms not higher not lower if you go too low it will gonna be too slow and it will bump a lot.
Can you cut a hole in a stainless steel sink?
Absolutely, you can cut a hole in a stainless steel sink. They typically come with pre-drilled holes, which is a good indicator that it's doable.
Why is there an extra hole in sinks?
They serve two functions: to prevent an overflow with the drain stopper engaged and to provide an escape route for air in the drain. Without this hole, a full basin of water would drain slowly because of the resistance it puts on air escaping up from the drain.
What is overflow hole in sink?
An overflow opening is a small hole drilled in the top of the threaded portion of the drain that allows overflow water from the sink to enter the drain pipe. If your sink features an overflow, it is very important to purchase a drain with an overflow opening so that your sink and drain function properly.
How to enlarge a hole in a milk bottle?
Place a plastic bucket under the hole you need to enlarge. Set a water-filled 1-gallon milk container next to or above the hole, depending on the hole location. Puncture the container with an 8d nail at a location that points toward the hole. Do not remove the nail.
How to spin a bur?
Pull the rotary tool's trigger to spin the bur. Keep the tool body and cord out of the water. Align the bur's cutting flute with the hole's edge. Move the tool in a clockwise direction as you lightly touch the porcelain. Do not apply heavy pressure toward the sink. Keep the water flowing in a manner that keeps the area wet.
Is it hard to drill a hole in porcelain?
By Ely Hauser. The hard nature of porcelain makes it difficult to drill. This difficulty increases when you need to enlarge an existing hole in a porcelain sink. Attempting to drill the hole larger can cause the drill bit to wander, or in some cases, cause it to break. Given the expense of the drill bit required to drill porcelain, ...
Who is Ely Hauser?
Writer Bio. Ely Hauser is a union tradesman with more than 20 years of experience in the construction industry. He has also been a writer since 2002, contributing to the "Brazoria County Facts" newspaper, as well as various outdoor and construction websites. Related Articles.
How to widen a hole in porcelain sink?
A slower and less accurate way to widen the hole in a porcelain sink is to use a rotary tool with a grinding accessory . This method also generates a lot of heat, so you still need the water bottle to spray water on the porcelain while you're working, and don't forget the goggles. Run the rotary tool at about half speed and keep moving ...
How to hang a water bottle over a sink?
An easy setup calls for a 1-liter plastic soda or water bottle that you can hang over the sink with a length of twine or wire. Drill two or three holes in the bottom of the bottle using an eighth-inch or narrower drill bit and then tape over the holes with duct tape and fill the bottle with water. Hang the bottle over the sink, put ...
Why do you insert wood in porcelain?
The purpose of the wood insert is to keep the hole saw centered while you cut the porcelain, so if it starts to rotate with the saw, it isn't a problem as long as it stays in the hole. Run the drill at a low speed and avoid putting extra pressure on the saw while it's cutting.
What is porcelain tile?
Porcelain is basically ceramic that has been fired at a high temperature to make it almost glasslike, and like glass, it's fairly fragile. When tile pros cut ceramic or porcelain tile, they usually use a wet saw, which continuously sprays water on the tiles as you push them through the blade. You need to use water in the same way ...
Is a hole saw faster than a hole saw?
The hole saw is definitely faster, but it's a little riskier because it generates more heat. No matter how you do the job, you have to do something to keep the porcelain cool so it doesn't crack. Advertisement.
Who is Chris Deziel?
Chris Deziel is a contractor, builder and general fix-it pro who has been active in the construction trades for 40 years . He has degrees in science and humanities and years of teaching experience. An avid craftsman and musician, Deziel began writing on home improvement topics in 2010.
How many holes does a Danze sink have?
Edit: Forgot to mention that the type of sink has 3 faucet holes (although this danze faucet only needs the center one) and they are 4" apart. I only want to slightly increase the diameter of the middle one. You have a one hole faucet and want to use it on a 3 hole sink.
How wide is a brass faucet?
The problem is that the brass tailpiece on the faucet physically can't fit through the holes in the sink. The holes are only 1 1/4" wide and the tailpiece looks to be at least 1 3/8".
Can you drill into porcelain?
you absolutely can't drill into porcelain without a very high probability of cracking it. But it seems in your case you're not making a new hole, but instead enlarging it. I wouldn't use any hole-drilling equipment, but rather GRIND it larger. I've never done this before but I'm familiar with ceramics and porcelains.
