Quick fix for your DStv A6 Remote
- Clear the line of sight between your remote and the decoder by removing any object that may be in front of your decoder.
- Weak or dead batteries can be a problem for your remote. ...
- If it won’t work but the green light is still blinking, press and hold the INFO button for three seconds to restore it to mode 1. ...
Full Answer
How do I Reset my DStv remote?
Let us go through the reset procedure and for a blueprint on how to unlock DStv remote. Hold down both the ARC and Standby for about 3 seconds. During this step, the remote lights should change to amber. Continue holding the ARC button as you release the Standby. While you are still pressing the ARC button, dial 9499.
Where is the standby button on a DStv remote?
Locating the Standby button on a remote The standby button is usually located at the upper end of the remote. It is also known as the power button and it carries the symbol:. Posted in DStv Remotes TV Network
How do I reset the remote control to default settings?
Hold down both the ARC and Standby for about 3 seconds. During this step, the remote lights should change to amber. Continue holding the ARC button as you release the Standby. While you are still pressing the ARC button, dial 9499. During this step, you should observe three green blinks. Now, release the ARC button to complete the reset process.
What should I do if my Remote controls don't work?
Remove all the dirt on the board, the membrane and the remote buttons. Dry the parts. Check the small metal springs and the soldered parts to make sure nothing is broken.
See more
How do I fix my unresponsive DStv remote?
Reset DStv remoteHold down both the ARC and Standby for about 3 seconds. During this step, the remote lights should change to amber.Continue holding the ARC button as you release the Standby.While you are still pressing the ARC button, dial 9499. ... Now, release the ARC button to complete the reset process.
Why is my decoder not responding to my remote?
You may also need to press the CABLE button at the top of the remote to direct the signal to the receiver and then try a few functions (Guide, Menu/Settings, etc.) to see if it is only certain buttons that do not work. Failing this, you can try resetting your receiver. Unplug your receiver and wait 15 seconds.
How do I reprogram my DStv remote?
Step 1 Press and hold STANDBY and OPTIONS simultaneously for more than 3 seconds. The LED will give 2 short RED blinks to indicate the remote is now in programming mode. Step 2 Press 9 and then 8 then 1 The LED will blink RED once when you press 9 and 8 and twice RED once you have entered all digits.
Where is the reset button on DStv remote?
Resetting your remote is simply about restoring it to its default mode – the TV1 mode. To reset a DStv B5 remote, press and hold the i (that is, INFO) button until the green light next to TV1 blinks once. Once the green light blinks, your reset is complete.
What causes a remote to not change channels?
Make sure there are no obstacles between the remote and your TV. Move closer to the TV and make sure the remote is pointed directly at the TV's front panel. Make sure the batteries are installed correctly. Try fresh batteries.
How do I reset my DStv decoder without the remote?
Process of how to reset DStv decoder without remote First, unplug the power button from your decoder and ensure it is completely turned off. You can check for this by ensuring all its lights are turned off, and none is blinking. Turn it back on and press the reset button on your decoder.
How do I fix my DStv A7 remote?
If your remote is not responding, Press the DStv button and the Standby button will light up. If the Standby button does not light up, this means your batteries are dead. Replace the batteries with new ones and try again. Replacing the batteries can also help if your A7 remote is blinking red randomly.
How do I reset my Explora remote?
Resetting a DStv Explora remote for DStv PVR Firstly, press and hold the SHIFT button and wait for the three blinks on the LED. Finally, enter the resetting code 977, and you are done. Your remote is now ready to use.
Why is the power button on my DStv remote flashing?
When using the remote : if there is one RED blink, the remote is already in “Standby Relay” or “Volume Relay” mode, but nothing has been programmed to that button, or there is in an error with the programming sequence.
How can I fix my remote?
0:103:40How to fix a remote control - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's not that many things inside a remote they can actually go that wrong so it's not too hard toMoreThere's not that many things inside a remote they can actually go that wrong so it's not too hard to fix first thing you want to do though is test the batteries because if you have weak batteries.
How do I reset my DStv A6 remote?
How to reset DStv A6 remotePress and hold ARC and STANDBY buttons for 3 seconds.While holding the ARC button, release the STANDBY button.While holding the ARC button, press 9949.Finally, release the ARC button to complete the reset.
How do I reset my OVHD remote?
Press menu from the remote control.From the screen scroll to setting then press ok.Under setting go to installation and press ok. Parental pin code will be required, enter 1234.Scroll down to factory reset and press ok.Press ok again to start channel search.
How do I reset my GOtv decoder remote?
Reset GOtv channels via MenuPress "Menu" on your remote.Select "Advanced Options".Then select "Installation".Select "Tuning".Then select "Automatic Scan" and press the “OK” button.Press the exit button on the remote once scanning is completed.
How do I reset my GOtv decoder manually?
2:355:30How to Reset your Gotv Decoder - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe first option is installation you press ok there then you scroll down to reset and once you getMoreThe first option is installation you press ok there then you scroll down to reset and once you get to reset you press ok. And you get a prompt.
How can I use OVHD decoder without remote?
The decoder will pick up the OVHD signal automatically. The decoder must be activated using the cellphone by entering *120*6843*1# and then follow the menu.
How to fix DSTV remote?
Follow these steps to fix a DStv remote not responding: 1 Check your batteries: You should check your batteries to ensure they have enough power. If the batteries are low, they will not work when changing channels, increasing the volume, or reading a message. Also, remove your batteries and check whether you have inserted them properly. The positive and negative ends should be on their corresponding ends on the terminals. 2 Check for an electronics glitch An electronics glitch can occur on a DStv remote’s signal before that signal reaches the DStv decoder. You can correct it using the following steps.
Why is my DSTV remote not working?
When your DStv remote is not working, it can be inconvenient for you to continue watching or changing to a different channel. Technically, several reasons can explain why your remote control is not working. First, the power in your batteries may have depleted, or you have incorrectly inserted them. Also, the transmission window or the upper edge of the remote control may be dirty. If you are using an old remote control, the positive and negative terminals may have rusted. Luckily, you can fix some of these issues by yourself at home.
What does it mean when a remote light flashes?
If it flashes the light, it means your DStv remote is working well , and you may have a problem with your decoder’s remote sensor. But if it does not flash the light, you need to buy a new remote or replace it with a functional one.
What happens if the transmission window is not clear?
If the transmission window is not clear, that communication cannot happen. Thus, you need to clean the upper edge of the remote control and try again. Check for signal interference When using your DStv remote, there should not be any objects between its sensor and that of the TV. An object will block the infrared signal.
Why does my remote blink red?
When that happens, it means that you have not programmed anything on those two buttons . Or, the programming sequence has a problem that needs fixing . Thirdly, you will see one red blink when using the remote. That means your remote is already in volume or standby relay mode.
Why is my remote control battery dirty?
First, the power in your batteries may have depleted, or you have incorrectly inserted them. Also, the transmission window or the upper edge of the remote control may be dirty. If you are using an old remote control, the positive and negative terminals may have rusted.
How to check if a battery is working?
Check your batteries: You should check your batteries to ensure they have enough power. If the batteries are low, they will not work when changing channels, increasing the volume, or reading a message. Also, remove your batteries and check whether you have inserted them properly. The positive and negative ends should be on their corresponding ends on the terminals.
What causes a remote to touch itself?
For most remotes, there is always a rubber layer between the remote button and the electronic board inside. If something goes wrong with this rubber layer or the surface of the board, it could cause the remote to “touch itself.”
Why is my remote not responding?
Your remote needs to have a clear path to your decoder. If there is anything cutting through that path, your decoder will not receive commands from the remote. This may be the reason your remote is not responding.
Can a multichoice remote control be faulted?
MultiChoice items are well known for durability and their remote control is no exception. But they can sometimes develop a fault. Here are the common DStv Remote control problems and the best solutions you can apply to fix them.
How & Where to buy an original DStv remote control
You can get an original DSTV remote control at MultiChoice branches, agencies, and retail outlets nationwide. That way, you’ll avoid buying a fake one. Furthermore, they will be able to provide you with a remote type that matches your decoder model.
Which one should you buy?
Apparently, the different types of DStv decoders have varying remote controls. Although they are products of the same company, the RC of a particular decoder type/model may not be completely compatible with another decoder type.
How much does it cost?
Depending on the remote controller type, the price ranges from 1,500 to 2,500 Nigerian naira. From our observation, HD decoders have the most expensive RCs while Standard and Explora are comparably cheaper.
Quick fix for your DStv A6 Remote
Clear the line of sight between your remote and the decoder by removing any object that may be in front of your decoder.
How to Switch Modes
Your device can function primarily in three modes: 1, 2 and 3, where mode 1 is the default mode. Here is how to switch modes on an A6 remote control.
How to reset DStv A6 remote
You will need both hands when carrying out a reset. Here is how to delete all programming on your remote and reset it to factory settings.
Remote Functions
There are myriad functions and combinations on your A6 remote. Putting all of them in a single programming article will make things very confusing.
Conclusion
Just like any other electronic device, a DStv remote control can also get broken. Sometimes everything on the remote including the LEDs will stop working. At other times, certain buttons will malfunction.
What is DSTV remote?
A DStv remote control uses infrared to relay a signal to the dstv decoder. Unlike Bluetooth, signals transferred using infrared have – a straight – Line of Sight.
How to open a remote control?
Get a flat metal: you could use a small kitchen knife. Put the knife properly on the lining at the side of the remote and force it open. Be careful! It won’t be my fault if you wound yourself.
What is remote on a flat board?
Unlike other electronic devices, remotes don’t have complex structures. All you have in a remote is a rubber membrane on a flat board just like what you have in the image below. The rubber membrane comes with the buttons but in rare cases, the buttons may be separated from the membrane.
How to tell if your remote is working?
Turn on your smartphone camera, point your remote at the camera and try to press some buttons. If the remote is working, you will see a white light in the tiny bulb on the remote.
Can you use a faulty TV remote?
Trying to use a faulty dstv remote can be very annoying. If your dstv remote is not working, that doesn’t make it completely useless. You can make it work again in a few, simple – do it yourself – steps. Let me show you how. Check For Infrared Signal. Check to see if the remote is still sending out a signal. You can do this by using a smartphone.
