How To Inflate A Lay Z Spa Hot Tub - 5 Easy Steps
- Preparation Steps For Easy Inflation. The first thing you’ll need to consider before unpacking your new hot tub is...
- Connect The Pump. Once you have the hot tub in position, you need to connect the pipe from the airjet outlet on the...
- Inflate Your Lay Z Spa. Now you need to switch on the jets. It will take...
How do I know when my Lay z Spa is fully inflated?
Keeping this in consideration, how do you know when your Lay Z Spa is fully inflated? On theMonaco, Palm Springs Siena, Hawaii AirJet and theHydroJet models come with a pressure gauge, these should be inflatedto between 7-10psi. TheVegas Miami, Paris, and other models should be inflateduntil touch soft.
How do you inflate an inflatable spa lid?
The inflatable lid can be inflated using the spa pump and the inflation hose. Attach the inflation hose to the ‘C’ connection on the pump, insert into the inflation valve and press the bubble function on the pump unit. How do I know when the spa is properly inflated?
How long does it take to set up a Lay-z-spa?
Lay-Z-Spa hot tubs require no tools for set up and are inflated by using the supplied pump. This takes approximately 5 minutes. Please refer to your Instruction Manual for specific set up information or watch our handy Setup Videos.
How do I deflate my spa?
In order to deflate your spa, drain the spa of any water then fully unscrew the inflation valve and completely remove. This will cause the spa to start to deflate.
How do I make my Lay Z Spa inflated?
Does A Lay‑Z‑Spa Need Constant Power To Stay Inflated? No, a Lay‑Z‑Spa does not require the pump to be kept inflated. The pump is used at initial setup to inflate the hot tub and to top it up if required.
Why is my lazy spa not inflating?
If your Lay‑Z‑Spa liner is deflating we recommend the following troubleshooting steps: Step 1 ‑ check if the inflation valve is too loose: Ensure that the valve is fully inserted and fully secured into the inflation hole.
How do you use a Lay Z Spa pump?
1:448:12Lay Z Spa Operating Instructions for Lay Z Spa Control Panel - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn press and hold. The power button and the power button will light up green and the display willMoreOn press and hold. The power button and the power button will light up green and the display will come up bright with the temperature. By default the display.
How do I air up my hot tub?
3:0910:35HOW TO SET UP your new Lay-Z-Spa HOT TUB - YouTubeYouTubeStart of suggested clipEnd of suggested clipSorted the lid comes in two parts there's a white inflatable element. And also the main grey coverMoreSorted the lid comes in two parts there's a white inflatable element. And also the main grey cover itself the inflatable element sits inside the lid it's held in place by some elastic.
How do you know when your Lay Z Spa is fully inflated?
How do I know when the spa is properly inflated? On the Monaco, Palm Springs Siena, Hawaii AirJet and the HydroJet models come with a pressure gauge, these should be inflated to between 7-10psi. The Vegas Miami, Paris, and other models should be inflated until touch soft.
Why has my hot tub deflated?
It may simply be that your tub's inflation valve or deflation valve adapter is faulty, or that it's too loose. A loose inflation valve is likely to be a key cause of air escaping through a Lay-Z-Spa. Once again, it can be uncommon for problems like this to arise in the most robust of tubs.
Should my inflatable hot tub pump run all the time?
Leave it running! This may be surprising to hear, but turning your inflatable spa off frequently is actually not the most efficient. If you want to use your inflatable hot tub regularly, say more than three times a week, the most economical and effective way is to keep the spa heater running.
How do you inflate a Lay-Z-Spa Palm Springs hydrojet?
2:288:13How To Setup Your Lay-Z-Spa Palm Springs Hydrojet - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover.MoreCover.
Can you add air to an inflatable hot tub?
6:019:42[Problem Solved]How to add air (re inflate) your portable spa/hot tub ...YouTubeStart of suggested clipEnd of suggested clipSo that we can start inflating the spa or adding air to the spa okay i have my pump plugged back inMoreSo that we can start inflating the spa or adding air to the spa okay i have my pump plugged back in first thing you're gonna gonna wanna do is power it on.
Can you fill inflatable hot tub with warm water?
Fill Your Lay‑Z‑Spa With Water From The Hot Tap It is far more energy‑efficient to start your hot tub up with warm water rather than filling the hot tub with cold water and waiting for the pump's heater to do all the work.
Can you fill lazy Spa with hot water?
In most cases it is advised not to fill your hot tub or spa directly with hot water but if you do, make sure the water temperature is not excessive, for the best result remove air lock (see below) then increase the cool water in the main water area by putting the hot water into cool which will slowly increase the ...
How to reduce wind exposure in a lay-z-spa?
Surroundings: Placing your Lay-Z-Spa near a windbreak such as a fence will help to reduce wind exposure, helping it to retain more heat and in turn help to reduce your running costs. You should also consider where you will drain the water when required.
What is a layz spa?
Whenever the Lay-Z-Spa's heater is turned on, the filtration function is automatically activated.
What temperature should a spa be?
When not in use, we would recommend setting your spa at a temperature of between 34°C and 38°C, and then an hour or so before increasing this to 40°C. A Lay-Z-Spa's heater is thermostatically regulated. The heater will therefore only switch on when the temperature falls a couple of degrees below your desired temperature.
How far away should a hot tub be from the ground?
The socket that the hot tub is being plugged in to should be grounded and at least 4 metres away, at a height of at least 1.2m from the ground. Please Note: You should not overload your plug socket. We recommend that you only run power to your Lay-Z-Spa from a plug socket and nothing else at the same time.
When does a spa heater switch on?
The heater will therefore only switch on when the temperature falls a couple of degrees below your desired temperature. Consequently, this is much better than letting your spa's water rise and fall from hot to cold, as this will require much more energy to bring the spa back up to temperature.
How long should a child use a lay-z-spa?
We recommend that children over 8 years old only use a Lay-Z-Spa for a maximum of 10 minutes at a time.
Is chlorine good for hot tubs?
Chlorine or bromine is a powerful sanitiser which is necessary to keep your hot tub clean and healthy. As a body of still water, a hot tub runs the risk of becoming stagnant and dangerous if not treated properly. Therefore, it is essential to use ClearWater Chemicals to help maintain the water health of your spa.
Why does air shoot out of my tub?
It doesn’t always have to be a puncture that’s causing air to shoot out of your tub. It may simply be that your tub’s inflation valve is faulty, or that it’s too loose. A loose inflation valve is likely to be a key cause of air escaping through a Lay-Z-Spa.
Can a lay-z spa tub be punctured?
A puncture could occur for any reason. Why Lay-Z-Spa tubs are generally very robust and durable, they are still susceptible to sharp points and objects likely to tear. You should be very careful to check the full lining once completely deflated.
Can an inflatable spa leak?
One of the biggest problems inflatable spa owners may face is a deflating hot tub . Unfortunately, as a fully inflatable system, there may come a time when you find that your spa springs a leak. The best tubs and spas should hold up for years to come.
How to deflate a spa?
In order to deflate your spa, drain the spa of any water then fully unscrew the inflation valve and completely remove. This will cause the spa to start to deflate. Once the spa has deflated, you can carefully fold the spa, to remove the final bits of air.
What happens when a spa pump is too hot?
The spa pump will heat the water to a couple of degrees higher than the set temperature, it will then stop the heating function until it has dropped to a few degrees below the set temperature when the heater will restart .
How long to wait before applying repair patch?
Ensure that the surface to be repaired is cleaned and completely dry before applying the repair patch. Please wait at least 30 minutes from applying the patch before re-inflating to allow the adhesive to dry.
Do spas come with a cushion?
The spas do not come with a separate inflatable cushion, as they have a cushioned base. The circular inflatable part supplied is a lid to help insulate the spa and should be placed inside the top cover.
Can you change the water in a spa?
If you are happy that the water is clean and safe it is fine to continue to use the water, in the event that you are unsur e, it is safest to change the water.
Does the Lay Z Spa pump filter water?
Does the pump unit filter the water? The Lay-Z-Spa pump unit filters the water via a replaceable filter. When the heater is turned on the filter will also be active, but you can activate the filter without the heater.