How to Install a Kitchen Sink Drain
- Step 1: Measure the Sink’s Drain Hole ...
- Step 2: Remove the Old Strainer ...
- Step 3: Apply Plumber’s Putty to the Basket Strainer ...
- Step 4: Insert the Basket Strainer into the Sink Drain Hole ...
- Step 5: Slip the Friction Band and Rubber-Seal Washer over the Base of the Strainer ...
- Step 6: Tighten the Nut to the Basket Strainer ...
How do you install a Kohler kitchen faucet?
Drill the faucet holes, and install the faucet to the countertop according to the faucet manufacturer’s instructions. Install the strainer to the sink according to the manufacturer’s instructions. Clean the countertop. Carefully position the sink into the countertop opening so the “Kohler” logo is to the back. Verify the fit and position.
How to replace a kitchen sink drain?
Reassemble the drain connections to complete the installation. First, replace the locknut over the friction ring and tighten it down with your pliers or wrench. Then, do the same to the smaller coupling nut to rejoin the drain and drain line. Give each fitting an extra quarter-turn to make sure they’re nice and tight.
How do you install a new drain in a bathroom?
First, decide whether you’ll be installing your new drain in your bathroom or the kitchen—the process is nearly identical, but the parts you’ll need differ slightly. Remove your existing drain by loosening the slip nuts holding it place and lifting it out from the top side of the sink.
How do you assemble a new plumbing installation?
Once you’ve gotten this far, assembly is as easy as applying plumber’s putty to the area around the drain hole or flange, slipping the new drain into place, and putting the plumbing back together in the opposite order that you disassembled it. Place a spacious container under the sink to catch waste water.
How do you install a kitchen sink drain assembly?
0:222:08How to Replace a Kitchen Sink Drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow when replacing the kitchen sink drain. You'll need a large pipe wrench needle nose pliers andMoreNow when replacing the kitchen sink drain. You'll need a large pipe wrench needle nose pliers and plumber's putty first loosen the nut that attaches the tail piece the old drain.
How do I install a Kohler pop up drain?
1:393:31How to Install a Pop-Up Drain in a Bathroom Sink | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipPush the drain collar down into the hole any excess putty will be pushed out and can be easilyMorePush the drain collar down into the hole any excess putty will be pushed out and can be easily removed after the rest of the drain is installed slide the rubber gasket onto the shaft.
Do I need plumbers putty for kitchen sink drain?
If you need to stop or prevent leaks around your faucet, sink or tub drains − plumber's putty is the product you need.
How do you remove the drain from a Kohler sink?
Removing the Stopper The ball rod holds the stopper in the drain. To reach the stopper, the ball rod needs to be removed first. The ball rod is inserted into the side of the drain and attached with a nut. To remove, unthread the rod nut, pull the ball rod out, and remove the stopper from the drain.
How do you install a push pop-up drain?
0:361:58How to Install Push Pop-Up Drain Plug Stopper and Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then goMoreTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then go ahead and remove the old flange. You'll want to clean up the area of the drain hole in the sink.
How do you replace a sink pop-up drain?
0:293:31How to Replace Your Bathroom Sink Pop-Up Assembly - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you can see exactly what needs to be done lift strap pivot rod and spring clip remove the pop-upMoreSo you can see exactly what needs to be done lift strap pivot rod and spring clip remove the pop-up plug loosen the slip nut that fastens a tail piece to the p-trap.
Should I use silicone or plumbers putty for sink drain?
Plumbers Putty or Silicone for Sink Drain You can use silicone caulk or plumber's putty to seal sink drains. Plumber's putty may crack and cause leaks as the clay dries out with time. But it's the preferred choice of sealant if you'll be adjusting or removing the drain.
Can you use caulk to seal a sink drain?
Both plumber's putty and silicone caulk provide a watertight seal for a sink drain. You must seal the area between a sink's drain body and the actual sink surface. Otherwise water will leak out between the two and begin dripping under the sink.
What do you use to seal a kitchen sink drain?
0:002:38“silicone” INSTEAD of “plumbers putty” on kitchen drain basketYouTubeStart of suggested clipEnd of suggested clipA common place that sinks leak is at the seal under the sink drain basket a lot of people useMoreA common place that sinks leak is at the seal under the sink drain basket a lot of people use plumber's putty and we have two but through the years we have found that silicone. Works the best you can
How do you install a sink drain pipe?
1:184:49How to Plumb a Drain - Sink Drain Pipes - YouTubeYouTubeStart of suggested clipEnd of suggested clipInto place take a nut with the threads facing down slide it up the tailpiece on the sink drain whileMoreInto place take a nut with the threads facing down slide it up the tailpiece on the sink drain while holding the nut into place choose the proper size washer.
How do you remove a Kohler pop-up tub drain?
0:462:14Removing a lift-&-turn stopper (1-step) - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically you'd grip it underneath that top part and just grip it tight turn it once he getsMoreBut basically you'd grip it underneath that top part and just grip it tight turn it once he gets loose. Enough. Just keep turning. And it comes out.
How do you install pop-up emitter gutters?
1:125:12How to Install POP UP EMITTER - 3 Ways - 2 kinds of pipe - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we want that water to drain down into the swale just a little bit of a trench will be fine. AndMoreSo we want that water to drain down into the swale just a little bit of a trench will be fine. And that's the basics. Of your pop-up.
How does a push pop-up drain work?
A pop-up drain assembly is a drain that gives you an option to seal your drain to hold water by simply pushing on it to close and to open. Pop-up drains are designed to come in two different options “with overflow” or ”without overflow” openings. They are simple to use and quick to install.
What is the flange part of a Kohler drain?
The flange part of a colored drain is made of metal and has the KOHLER logo imprinted on it. The coordinating basket strainer is made of plastic and has slotted holes. The bottom of the strainer contains an o-ring to seal the drain when in the closed position.
What is the o-ring on a Kohler drain?
Metal drains have the KOHLER logo imprinted on the flange. The coordinating strainer has round holes. The bottom of the strainer contains an o-ring to seal the drain when in the closed position.
What is a gasket on a drain pipe?
The gasket ensures a watertight seal when you connect the drainpipe with the tailpiece. Carefully align the top of the drainpipe with the bottom of the tailpiece. Attach the connector ring to the drainpipe and drive it to the threaded brass tailpiece base.
How to seal a sink drain with a basket strainer?
Press down the basket strain into the hole for the sink drain just hard enough to achieve a good seal from the putty between hole on the drain and the basket strainer.
What is included in a kitchen sink drain kit?
The components making up the sink drain kit include rubber-seal washer, a fastening nut, basket strainer, friction-protection band, and a tailpiece that connects the drainpipe and the kitchen sink drain. You should ensure that the tailpiece also matches the size of your drainpipe.
Why should putty be equal in diameter?
The rolled-up putty should have an equal diameter down its stretch to avoid one part of the strainer appearing more padded than others.
How to fasten a nut to a basket strainer?
Turn the nut in a clockwise motion to fasten it to the threaded base of the basket strainer.
How to tighten a filter nut?
Use the needle-nose pliers to hold the filter’s base in place while using a wrench to tighten the nut.
Why do you need to measure the drain hole?
The reason you need the measurement of the sink’s drain hole is to guide you in the purchase of the appropriate sizes of the sink drain kit.
How to loosen locknut on drain?
If the drain spins while you’re attempting to loosen the locknut, steady it by spreading the handles of a second pair of pliers inside the top of the drain, inserting the blade of a screwdriver between them, and holding the screwdriver with your free hand.
How long does it take to install a sink drain?
Putting in a sink drain is a simple home improvement project that anyone can complete in less than half an hour. First, decide whether you’ll be installing your new drain in your bathroom or the kitchen—the process is nearly identical, but the parts you’ll need differ slightly.
What is a P trap?
The P-trap is the curved section of pipe at the base of the sink’s plumbing. If you’re installing a brand new drain on an unused sink, you can skip straight to preparing your plumber’s putty for the area around the drain hole.
How to get old locknuts to move?
In this case, spraying the edges with a penetrating oil or tapping them gently with a hammer and chisel can help you get the locknut moving.
How to get rid of water in sink?
1. Place a spacious container under the sink to catch waste water. Grab a bucket, bowl, or spacious plastic food storage container and set it on the floor directly beneath the sink. It will collect any water that happens to spill out when you disassemble the plumbing.
What happens if you don't put a drainage container down?
If you don’t take the precaution of putting a drainage container down, you could end up with water all over your floor.
Is it better to use too much or too little putty?
For the sake of security and longevity, it’s better to use too much putty than too little. You can easily remove the excess once you’ve finished the installation. Your new drain assembly may come with a separate gasket for the flange, in which case you won’t need plumber’s putty.
