- Attach the white wire to the center neutral terminal.
- Connect the red wire to the right hot terminal
- Attach the black wire to the left hot terminal.
- Attach the green wire to the green grounding screw or dryer case.
- Remove the masking tape labels.
How to install 4 prong and 3 prong dryer cord?
- Unplug the dryer cord before working on the appliance.
- Do not plug a dryer cord into a receptacle unless it is properly and completely connected to the dryer.
- Almost all manufacturers sell dryers without a cord attached, allowing you to select 3-prong vs. ...
How do you install an electric dryer?
- First of all, your vent must be heavy metal, not plastic or metal foil.
- Select the route that follows the straightest/most direct path to the outdoors, with as few elbows/turns as possible.
- Bent the vent carefully so as not to hinder its effectiveness.
How to attach dryer cord?
Remove the plate from the dryer to expose the wiring terminal block for the cord connections. Set the plate and screws aside. Install the Cord Insert the dryer cord into the hole near the terminal block. Secure the green cord wire under the ground screw on the dryer body. Tighten the ground screw firmly with the screwdriver or nut driver. Tip
Can you plug a dryer to a stove outlet?
You could technically use an electric range cord on a dryer, so long as the receptacle matched it, because the range cord is rated at a higher amperage, and it could handle the dryer's lower rating. Using a dryer cord on a range could result in a fire.
How do you put a new cord on a dryer?
0:291:20How to install a 3 wire power cord to your dryer. - YouTubeYouTubeStart of suggested clipEnd of suggested clipInsert the cord strain relief. One side up one side down then screw the strain relief togetherMoreInsert the cord strain relief. One side up one side down then screw the strain relief together leaving a gap for the cord to pass through insert. The cord. Through the strain relief.
How do I change a 3 prong dryer cord?
4:2513:34How To Change A Dryer Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'm going to do is I'm going to pull you in close on the dryer. I'm going to show you theMoreSo what I'm going to do is I'm going to pull you in close on the dryer. I'm going to show you the two different ways that it can be hooked up I'm gonna take the clamp off I already taken the clamp off
How do you install a 4 prong dryer cord?
1:112:22Install a 4 wire power cord to your dryer - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne tab up one tab down attach. The screws to the strain relief and thread the four wires. ThroughMoreOne tab up one tab down attach. The screws to the strain relief and thread the four wires. Through the strain relief tighten down the strain relief. After securing the strain relief remove.
Can you replace cord on electric dryer?
When replacing the existing dryer in your home, you can reuse its electric power supply cord if the old cord conforms to current safety codes and there is nothing wrong with the cord itself.
What are the colors on a 3 prong dryer cord?
Black is L1 or line one. White is neutral. And red is L2 or line two. The center wire on the three-wire cord is neutral and will always be installed in the center of the terminal block.
Can I use a 4 wire cord on a 3 wire dryer?
Don't panic if you have the older, three-slot dryer outlet. The Electrical Code allows this to remain in place, and you are allowed to replace the four-prong cord with a three-prong cord to match this outlet.
Are 4 prong to 3 prong dryer adapters Safe?
If you were to change from a four prong to a three prong and your dryer is designed to use 120 volts at some point, then that current will have to be returned on the ground leg. This is not acceptable by NEC code, nor is it safe.
Are all dryer cords universal?
Most new dryers come with four-prong plugs, but they can be used with three-prong cords to fit older dryer outlets. There are some dryers that don't have a cord at all, so you have to buy and install your own.
Is it easier to replace dryer cord or outlet?
If you are ready to plug in that new or used clothes dryer, but the plug on the dryer does not match the outlet on the wall, replacing the cord on the dryer is much easier and more economical than replacing the outlet on the wall.
Do all electric dryers have the same plug?
But there are two different outlet styles and plug-in cord styles used for these 240-volt electric dryers. Some have three slots, designed to accept appliance cords with three prongs, while other outlets have four slots, designed to accept four-prong cords.
Is it easier to replace dryer cord or outlet?
If you are ready to plug in that new or used clothes dryer, but the plug on the dryer does not match the outlet on the wall, replacing the cord on the dryer is much easier and more economical than replacing the outlet on the wall.
How do you replace a terminal block on a dryer?
0:321:29Whirlpool/Kenmore Electric Dryer Terminal Block #3397659 - YouTubeYouTubeStart of suggested clipEnd of suggested clipDown the tab in the back to release each of the three terminal block wires. Then remove the threeMoreDown the tab in the back to release each of the three terminal block wires. Then remove the three terminal nuts install the new terminal block by inserting the nuts into the block.
Are 3 prong dryer outlets safe?
A newer dryer run on a 3-prong system is an electrical hazard at best, even if nothing goes wrong, and a disaster if there is a short or loose wire.
Reusing an Old Dryer Cord
When replacing the existing dryer in your home, you can reuse its electric power supply cord if the old cord conforms to current safety codes and there is nothing wrong with the cord itself. However, you must replace the cord if it shows any signs of wear, so check it carefully for any fraying, kinks or other signs of damage.
3-Prong Dryer Cord vs. 4-Prong Dryer Cord
A 3-prong dryer cord was the standard for dryers prior to 2000. The National Electrical Code currently requires 4-prong dryer outlets in all new home construction. Existing homes may still use 3-prong outlets.
Helpful Tips on How to Change a Dryer Cord
Changing a dryer cord is simple but the project isn’t done frequently by most homeowners. Some tips might be new advice for beginners and others are worth repeating even to seasoned DIY-ers. Use common sense when learning how to change a dryer cord.
Open the Access Panel
You must make certain that the appliance is disconnected from its power source before beginning to work on changing a dryer cord.
Remove the Old Cord
After the terminals are labeled for easier installation of the new dryer cord, you can begin to remove the old cord.
Attach the New Cord
Feed the loose wires of the new dryer cord through the hole in the back of the unit. Then you can attach the new cord.
Replace the Access Panel
Double check that you have firmly tightened the terminal screws that connect the new wires. Now install the strain relief bracket to protect the connections and help avoid a possible short if the cord is yanked.
How to choose a cord for a dryer?
Most hardware stores and nearly all home supply centers offer cord sets for electric ranges and dryers with a choice of either 3 or 4 conductors for under $25 or so. These cord sets may look similar, but are not interchangeable due to different electrical ratings. Dryer cord sets are 240V/30A and range cord sets are 240V/40A for use in the U.S. & Canada.
What color wires are in a dryer cord?
Understand color coding of conductors in the cord set. If the dryer cord does have colored wires, white is the neutral wire to the center connector, the red and black wires are the hot line 1 and line 2 wires which connect to the 2 outer connections of the dryer terminal block. Don't forget the ground strap or green wire jumper from ...
How many conductors are needed for a dryer?
Modern appliances require 4 conductor cord sets (separate conductors or wires for line 1, line 2, ground and neutral). Generally, this setup is safer, because the current-carrying neutral is not connected to the dryer case. However, it is useless if the wall receptacle does not have a separate ground slot.
What is the center wire on a dryer?
Notice that the center wire (neutral wire) of the cord set goes to the center connector. Since in this case the neutral serves as a neutral and a ground connection, a jumper conductor (ground strap) is also connected to the center terminal and to the frame of the dryer. A green wire could also be used to connect the center connector to the frame of the dryer.
What is the wire on a LINE cable?
The Red and Black wires of the cable will connect to the LINE (L1 & L2) terminals. The white wire will connect to the Neutral (N) terminal after removing the any jumper between the N terminal and appliance frame or sheet metal or terminal marked as Ground (G or Ground symbol). The Green wire will connect to the Ground (G or Ground symbol) terminal. There should be no wire or jumper connection between the N and G terminals screws.
How much voltage drop on #10 wire?
Assuming copper wire, a #10 AWG wire that is 150' long (2 wires at 75 ft each) has a little less than a 6 volt drop: providing just over 234V from a 240 source. That's a little over 2% of loss. I would run the #10 for this length of cable. Conversely, a #8 cable of the same length has about a 3.5 volt drop, providing a little over 236 volts from the same 240 v source; or a 1.5% loss. The difference in cost between the #10 & #8 doesn't seem to be worth it and the voltage drop on the #10 is still low enough to safely operate the appliance.
How many amps does a dryer need?
Verify the electrical requirements of the dryer. Most sold for use in the U.S. and Canada require a 240 volt / 30 amp supply.
Why is it important to ground a dryer?
You must properly ground a dryer. Grounding reduces the risk of electrical shock by redirecting an electrical current away from the appliance in the event of an electricity surge. If you attempt to plug a new power cord into an outlet that hasn't been grounded, you risk short circuiting your electrical system ...
What happens if you plug a new power cord into an outlet that hasn't been grounded?
If you attempt to plug a new power cord into an outlet that hasn't been grounded, you risk short circuiting your electrical system and possibly the dryer if an electrical breakdown occurs. Only plug your dryer's new power cord into an outlet that meets local codes and ordinances.
Do you have to ground a dryer?
You must properly ground a dryer. Grounding reduces the risk of electrical shock by redirecting an electrical current away from the appliance in the event of an electricity surge. If you attempt to plug a new power cord into an outlet that hasn't been grounded, you risk short circuiting your electrical system and possibly the dryer if an electrical breakdown occurs. Only plug your dryer's new power cord into an outlet that meets local codes and ordinances. Don't risk using an old power cord that doesn't meet current safety standards.
Do you need a power cord for a dryer?
For the most part, you don't need a new power supply cord when you're replacing an old dryer with a new one. Since most new dryers don't come with a power cord, the appliance salesman might recommend that you purchase a new one.
