how do i install basket strainer

Inserting the Basket Strainer

More items

Full Answer

How do you install a sink basket strainer?

Installing the New Basket Disassemble the new basket strainer. Decide on a method of sealing. Roll out a piece of putty into a snake. Apply plumber's putty to the underside of the basket rim. Press the basket into the sink. Thread on the gaskets and nut. Scrape out excess putty, tighten further, and repeat. Reattach the tailpiece with new gaskets.

Are all basket strainers the same size?

At least in the United States, all basket strainers and sink drains are manufactured to the same size. Decide on a method of sealing. Plumbers can have strong opinions on this topic, but plumber's putty is generally a good default choice. However, putty can weaken plastic sinks and stain stone or other porous materials.

What is the best sealer for a kitchen strainer basket?

What Sealer Works Best for a Kitchen Strainer Basket? 1 1. Plumber’s Putty. Plumber’s putty is the choice of every professional plumber. It is readily available and creates a seal that lasts a long time. 2 2. Stainless Plumber’s Putty. 3 3. Silicone Sealant. 4 4. Rubber Washer.

How do I replace the basket strainer on my dishwasher?

Leave the water trap (U-bend) in place to keep sewer gases at bay. Unscrew the nut at the base of the basket strainer. Approach the basket strainer from below and unscrew the lowest nut. This should free the flanged tailpiece (a straight, collared tube) and top hat gasket (a small circle with a flat rim). Set these parts aside.

How to unscrew a basket strainer?

How to remove a large nut from a basket strainer?

What is a sink strainer?

How to flatten a basket rim?

When tightening a nut, what should you avoid?

Do you need to measure for a strainer?

See 3 more

About this website

How do you fit a strainer?

0:202:22How to Stop a Kitchen Sink From Leaking Where the Basket Is InstalledYouTubeStart of suggested clipEnd of suggested clipFirst. And if it's loose any compression. Or added compression we get on it well you should stop theMoreFirst. And if it's loose any compression. Or added compression we get on it well you should stop the clog. Now. What happens is it's going to give this a quick tug and that was a little loose.

How do you connect a kitchen sink strainer to drain pipe?

3:095:33How to replace basket strainer, kitchen sink drain. Easy ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you're positioned right in the center of the hole let's go back under the sink. We'reMoreMake sure you're positioned right in the center of the hole let's go back under the sink. We're gonna take our rubber gasket put that on first then the paper washer. And then the nut.

How do you use a basket strainer?

0:183:28How To Use Kitchen Sink Strainer Baskets To Save Water ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want to plug the drain. All you got to do is with this particular kind is twist it until theMoreIf you want to plug the drain. All you got to do is with this particular kind is twist it until the plunger can actually insert further down so it's got a setting for draining.

How do you seal a basket strainer?

1:444:00Leaky Sink: Basket Strainer - How to Fix The Most Common LeakYouTubeStart of suggested clipEnd of suggested clipPut on the rubber gasket the cardboard gasket and the basket nut torque it down until all the excessMorePut on the rubber gasket the cardboard gasket and the basket nut torque it down until all the excess putty comes squeezing.

How do you install a basket strainer in a kitchen sink?

4:317:05How to Replace a Kitchen Sink Strainer - YouTubeYouTubeStart of suggested clipEnd of suggested clipCenter within the drain. And firmly press down install the rubber washer followed by the frictionMoreCenter within the drain. And firmly press down install the rubber washer followed by the friction ring and lock nut tighten the lock nut with a set of adjustable pliers.

Do you use plumbers putty on kitchen sink drain?

If you need to stop or prevent leaks around your faucet, sink or tub drains − plumber's putty is the product you need. Plumber's putty is a sealing staple for professionals, homeowners and DIY-ers alike.

What does a basket strainer look like?

1:317:46Basket Strainer Explained - YouTubeYouTubeStart of suggested clipEnd of suggested clipThough this type of strainer the basket strainer will be used for high flow. Systems you won'tMoreThough this type of strainer the basket strainer will be used for high flow. Systems you won't normally use it when you need to have fine filtering. The reason is that the strainer.

How tight should a sink strainer be?

1:553:23Kitchen Sink Strainer - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhile you tighten the nut lying on your back if your strainer comes with a logo on it be sure theMoreWhile you tighten the nut lying on your back if your strainer comes with a logo on it be sure the logo is centered on the opening.

What is a basket strainer for a sink?

In plumbing, a sink strainer is a type of perforated metal sieve or mesh strainer used to strain or filter out solid debris in the water system.

Is it better to use plumbers putty or silicone?

The main difference between plumbers putty or silicone for sink drain is how easy the substances are to manipulate or remove. Plumbers putty is very easy to manipulate into tight areas, and it's also easier to remove. That makes silicone putty better for waterproofing, even if it's more difficult to work with.

Can I use Teflon tape instead of plumbers putty?

While a single plumbing project might call for both plumber's putty and Teflon tape, you cannot substitute one for the other. Teflon tape, also called plumber's tape or thread-seal tape, gives a reliable seal on threaded pipe joints for liquids and gases that may be under considerable pressure.

Can you use plumbers putty instead of rubber gasket?

Well, technically, you could use plumber's putty on rubber gaskets (as long as it's approved for use on rubber). But if you're assembling a new sink drain assembly, there's really no point, especially if it comes with its own fitted rubber gasket.

How do you connect a P-trap to a sink drain?

1:576:34How To Install P-Trap And Bathroom Sink Drain Piping - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your straight pipe. Put it up here. So lightly tighten it down like that again take your nut.MoreTake your straight pipe. Put it up here. So lightly tighten it down like that again take your nut. And then put on. Now take your p-trap.

How do you install a sink drain stopper?

1:393:31How to Install a Pop-Up Drain in a Bathroom Sink | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipPush the drain collar down into the hole any excess putty will be pushed out and can be easilyMorePush the drain collar down into the hole any excess putty will be pushed out and can be easily removed after the rest of the drain is installed slide the rubber gasket onto the shaft.

How do you stop a sink strainer from leaking?

Leaky Sink Repair Supplies If you find your leak is coming from the sink strainer, remove the strainer body, clean it, and replace the gaskets and plumber's putty. Or, replace the strainer with a new assembly, available in the plumbing section at just about every home center store in your neighborhood.

How do you install a drain in a stainless steel sink?

0:121:48How to Properly Install a Sink Drain in a Stainless Steel Sink - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to take some plumber's putty roll it and place it on the perimeter of the strainer.MoreWe're going to take some plumber's putty roll it and place it on the perimeter of the strainer.

How to replace basket strainer, kitchen sink drain. Easy ... - YouTube

The Home Mender, Dustin Luby, shows us how to replace your kitchen sink drain , basket strainer, stopper. Easy! You can do it!🏆 NEXT LEVEL STUFF-----...

How to Replace a Kitchen Sink Basket Strainer | Family Handyman

Roll plumber’s putty between your hands into a rope the size of a pencil and wrap it around the lip of the kitchen sink drain opening. Press the kitchen sink strainer firmly down into the putty, add the rubber gasket, friction ring and locknut under the sink, and retighten the locknut.

How to unscrew a basket strainer?

Unscrew the nut at the base of the basket strainer. Approach the basket strainer from below and unscrew the lowest nut. This should free the flanged tailpiece (a straight, collared tube) and top hat gasket (a small circle with a flat rim). Set these parts aside.

How to remove a large nut from a basket strainer?

Take off the large nut at the top of the basket strainer. There's one more large nut for you to unscrew. Remove this and you'll have complete access to the basket strainer.

What is a sink strainer?

A sink basket strainer is simple enough for anyone to understand. This mesh basket catches solid objects to save them from falling into the sink. Replacing one is usually a quick, simple job, but there are a few pitfalls to be aware of. Steps.

How to flatten a basket rim?

Apply plumber's putty to the underside of the basket rim. Coil it beneath the rim and use your thumbs to flatten it evenly against the surface. Use just enough putty to cover the underside of the rim completely. Apply too much, and you won't be able to push your basket flush with the sink.

When tightening a nut, what should you avoid?

Avoid extreme force when tightening the nut, or you may break it.

Do you need to measure for a strainer?

You don't need to do any measurements to choose your new strainer. At least in the United States, all basket strainers and sink drains are manufactured to the same size.

What is the best strainer?

The best strainers have either a spin-lock or a twist-and-drop style stopper. The spin-lock stopper doesn't have any parts that can wear, but screwing it in and out can be annoying. The twist-and-drop style is much easier to use but requires occasional O-ring replacement.

How to crack a locknut?

Cut the locknut. If all else fails, chuck a metal cutoff wheel into a rotary tool and cut the locknut. Cut until you reach the cardboard ring above the nut. Don’t cut into the sink. If the nut still doesn’t spin, fit your chisel into the cut area and smack it with a hammer to crack it open. Wear eye protection.

How to get a rusted locknut out of a lock?

If the locknut is rusted in place, spray it with penetrating oil. If you don’t have large enough pliers to get a good grip, loosen the locknut by tapping the locknut with a hammer and an old chisel. (If the locknut won’t move, see the next step, below.)

How long does it take to replace a sink strainer basket?

When the time comes to replace your sinker strainer, you will only need about one hour and a few items from your local home improvement store.

Can you remove a strainer with a rubber gasket?

With that removed, you can slip off the rubber gasket and remove the strainer.

Can you use needle nose pliers to remove locknut?

Instead of separating, sometimes the strainer will turn with the locknut as you try to remove it. If this happens, you will need to wedge a pair of needle nose pliers into the bottom of the strainer and secure it while you are removing the locknut. This is possible to do by yourself, but it is much easier with a helper.

How do you install a kitchen basket strainer?

Installing a kitchen basket strainer is an easy, quick task that requires minimal involvement. The tools you might need are

How do you clean a basket strainer?

To increase the longevity of your strainer, proper cleaning is advised. Since strainers collect the residue and gunk of waste, they tend to clog up sooner or later.

What is a kitchen sink basket strainer?

A basket strainer is a small equipment with a mesh screen that filters out foreign objects in your sink. Usually made of stainless steel, this device helps to keep the basin area clean, hygienic, and debris free. By catching solid particles, a sink strainer keeps the water line free and functional.

Why do I need a basket strainer for my kitchen sink?

It is basically a strainer shaped like a basket that filters matter out of the sink, so the drain pipes do not clog.

What material is a kitchen sink strainer made of?

Moving on, the material the basket is made of matters as well. The most common material for the kitchen sink basket strainer is stainless steel.

What to look for when picking a sink strainer?

It can be plain or decorative, but it will always need to get the job done. Mesh size, material, attached stopper are three of the main things to look for.

How much does a kitchen sink strainer cost?

Found in most home centers and supply stores, the price range for kitchen sink basket strainers is between 10 dollars to 60 dollars from amazon.

What is a fabricated basket strainer?

Fabricated basket strainers may have perforated wedge wire, mesh, or metal. They play an important role in many piping system components such as nozzles, sprinkler heads, valves, and turbines. Fabricated basket strainer. Depending on the type of application, you can choose cast metal modifications or piping connection.

What side of the basket strainer is the suction side?

Each of the compartments plays particular roles in the process. The basket strainer has two sides; one is the suction side, and the other is the discharge side. You will use a plug to drain the fluid in from the compartments. Fluid gets drained either from the top or the base.

What is the best detergent for cleaning a basket strainer?

Take, for example, Alconox is one of the best powder detergents you can go for when cleaning basket strainer. Note: Before you go for any cleaning detergent, you need to know the type of basket strainer material. It will ensure you don’t choose a cleaning detergent that reacts or affects your duplex strainer.

How many basket strainers are needed for pipeline strainers?

Although is an important classification criterion, the 4 basket strainers can work as pipeline basket strainers.

What is the best thing about simplex basket strainers?

The good thing about the simplex basket strainers is the flexibility.

How to disconnect flange tail end?

You should start by disconnecting or isolating the system. Gently loosen the basket strainer. You will find it quite easy to disconnect the flange tail end from the basket strainer using the right tool. Proceed to loosen the ring up above, and at this point, one of your hands has to grasp the basket strainer.

What is basket trainer?

According to the Fluid Controls Institute, a basket trainer is a vessel that retains or removes dirt/small foreign particles from a flowing fluid. It is an enclosure vessel, with openings allowing fluid to flow in and out consistently, with virtually no significant pressure drop.

What is a Sink Strainer?

In case you’re unfamiliar, a sink strainer is the metal sieve that keeps food and other debris from entering your drain. It looks like a mesh strainer and works as a filter for your sink.

Common Types of Sink Strainers

There are two common kinds of basket strainers. One type is secured by a lock nut, while the other is held by a plastic retainer and three screws. The lock-nut type is generally used for stainless-steel sinks because the lock nut tightens against the sink without bending the metal. But I’ll tell you how to install both.

Install Sink Strainer (Retainer-Type)

The process is much the same for a retainer-type installation. So follow the above process, but do this instead:

Final Thoughts

As you can see, installing a brand new lock nut sink strainer is straightforward. You can do this with very few tools (a screwdriver and pipe wrench) and there aren’t many steps involved.

Call 1-Tom-Plumber

Don’t hesitate to contact us here or call us at 1-Tom-Plumber (1-866-758-6237) if you need help with replacing or installing a sink strainer.

How to unscrew a basket strainer?

Unscrew the nut at the base of the basket strainer. Approach the basket strainer from below and unscrew the lowest nut. This should free the flanged tailpiece (a straight, collared tube) and top hat gasket (a small circle with a flat rim). Set these parts aside.

How to remove a large nut from a basket strainer?

Take off the large nut at the top of the basket strainer. There's one more large nut for you to unscrew. Remove this and you'll have complete access to the basket strainer.

What is a sink strainer?

A sink basket strainer is simple enough for anyone to understand. This mesh basket catches solid objects to save them from falling into the sink. Replacing one is usually a quick, simple job, but there are a few pitfalls to be aware of. Steps.

How to flatten a basket rim?

Apply plumber's putty to the underside of the basket rim. Coil it beneath the rim and use your thumbs to flatten it evenly against the surface. Use just enough putty to cover the underside of the rim completely. Apply too much, and you won't be able to push your basket flush with the sink.

When tightening a nut, what should you avoid?

Avoid extreme force when tightening the nut, or you may break it.

Do you need to measure for a strainer?

You don't need to do any measurements to choose your new strainer. At least in the United States, all basket strainers and sink drains are manufactured to the same size.