- 1 Remove the Existing Pop-Up Drain The first task is to remove the existing pop-up drain. ...
- 2 Replace the Drain Flange Before replacing the drain flange, thoroughly clean the sink area that was underneath the flange. ...
- 3 Replace the Drain Tailpiece The next step is replacing the drain tailpiece. ...
- 4 Insert the Drain Stopper ...
- 5 Reattach the Pop-Up Assembly ...
- 6 Reattach the Pipes ...
How do you install a pop up drain?
Instructions 1 Remove the Old Drain Assembly. ... 2 Prepare the New Pop-Up Drain Stopper. ... 3 Apply Pipe Joint Compound. ... 4 Apply Plumber's Putty. ... 5 Connect the Drain Parts. ... 6 Tighten the Drain Assembly. ... 7 Put the Drain Stopper Into Place. ... 8 Install the Pop-Up Lever. ... 9 Connect the Pop-Up Lever and Pivot Rod. ...
How do you attach a drain strap to a pivot rod?
Connect the vertical strap to the horizontal pivot rod by threading the spring clip on the rod. One end of the clip needs to be on each side of the strap. After the two rods are connected, check to make sure that the pop-up stopper opens and closes fully inside the drain opening.
How do you install a pop up stopper on a toilet?
Screw the pivot rod nut onto the threaded fitting on the side of the tailpiece, so the ball is secured to the tailpiece. Push the pivot rod up and down to make sure the stopper goes up and down freely in the drain. If the pop-up is working properly, you can tighten the nut hand-tight.
How do you attach a pop up lever to a faucet?
Install the Pop-Up Lever Feed the vertical pop-up lever down through the hole behind the spout of the faucet. Before connecting the horizontal pivot rod to the vertical lever, make sure your stopper is in the fully up (open) position. From below the sink, attach the connecting strap to the end of the vertical pop-up lever.
What is the phone number for drainage in Michigan?
Is EZ drain a weak pipe?
How do you install a pop-up drain assembly?
1:393:31How to Install a Pop-Up Drain in a Bathroom Sink | Repair and ReplaceYouTubeStart of suggested clipEnd of suggested clipPush the drain collar down into the hole any excess putty will be pushed out and can be easilyMorePush the drain collar down into the hole any excess putty will be pushed out and can be easily removed after the rest of the drain is installed slide the rubber gasket onto the shaft.
How do you install a push pop-up drain stopper?
0:361:58How to Install Push Pop-Up Drain Plug Stopper and Review - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then goMoreTake a pair of pliers. And loosen the lock nut remove the p-trap to free up the tail pipe then go ahead and remove the old flange. You'll want to clean up the area of the drain hole in the sink.
How do you install a pop-up drain in a vessel sink?
0:272:21Kraus Installation Series – Pop-up Drain (without overflow) - YouTubeYouTubeStart of suggested clipEnd of suggested clipBody next remove the coupling nut finally remove the gasket. Make sure this rubber gasket is flushMoreBody next remove the coupling nut finally remove the gasket. Make sure this rubber gasket is flush against the drain flange then insert it into the drain hole of the sink.
Does a pop-up drain need plumbers putty?
1:004:59How to Install a Bathroom Sink Pop Up Drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo it really doesn't matter the first thing is to just get the plumber's putty or siliconeMoreSo it really doesn't matter the first thing is to just get the plumber's putty or silicone underneath the lip.
How do you attach a pop-up waste?
1:053:16Ep3 Wash Basin Install - How to Install a Pop Up Waste - Plumbing TipsYouTubeStart of suggested clipEnd of suggested clipSo you can move up and down and you've also got the connects get the connector block in the rightMoreSo you can move up and down and you've also got the connects get the connector block in the right place. So you can tighten that all up and then you can move from the top.
How do you install an outdoor pop-up drain?
5:478:42How to install a lawn pop-up drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe next thing I will do is remove the top of the drain. And backfill right up flush with the top ofMoreThe next thing I will do is remove the top of the drain. And backfill right up flush with the top of this elbow. And then I will push the drain back on the elbow.
Are pop-up drains a good idea?
The good thing about pop-up emitters is that if there's no steady flow of water, the lid stays shut. That means no debris can make its way into the pipe. It's a great alternative to traditional drain grates that have a tendency to collect rocks, dirt or leaves that'll eventually clog the line.
How does a pop-up drain assembly work?
0:031:38What Is A Pop Up Drain For A Bathroom Sink? - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn between the faucet handles that would pop it up and down these just simply push to open or pushMoreIn between the faucet handles that would pop it up and down these just simply push to open or push to close to stop the water. This here has capability for an overflow.
Can silicone be used instead of plumbers putty?
You can use silicone caulk or plumber's putty to seal sink drains. Plumber's putty may crack and cause leaks as the clay dries out with time. But it's the preferred choice of sealant if you'll be adjusting or removing the drain.
How do you seal a pop up drain?
Place a small amount of plumber's putty to the bottom of the new flange. The putty will create a seal around the sink drain. If you cannot use plumber's putty on your type of sink, a small amount of silicone caulk will do. Tip: Warm the plumber's putty by rolling it in your hands before applying it to the flange.
Why does pop up drain have holes?
They serve two functions: to prevent an overflow with the drain stopper engaged and to provide an escape route for air in the drain. Without this hole, a full basin of water would drain slowly because of the resistance it puts on air escaping up from the drain.
When should you not use plumbers putty?
Do not use plumber's putty where you need adhesive strength (to bond materials or prevent them from moving) or where you need a watertight seal in exposed areas.
How do you put a pop up sink stopper back in?
1:314:58How to repair or reassemble pop-up sink stopper DIY video ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn the opening in the back of the the pipe there. So now we are going to insert the new pit rod intoMoreIn the opening in the back of the the pipe there. So now we are going to insert the new pit rod into the back of the pipe. You'll want to test to make sure that it actually goes into one of the holes.
How do you reattach a pop up stopper?
4:346:12FAST Sink Drain Stopper Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull push the stopper down a little bit farther. Till we hook it and I hooked it so I got it rightMorePull push the stopper down a little bit farther. Till we hook it and I hooked it so I got it right there.
How does a push pull drain stopper work?
A push-and-pull stopper is very similar to a lift-and-turn stopper in design and look, but it is pushed down to close and pulled up to open rather than twisted. Installation is also similar, with the stopper body attached to the drain with a setscrew found under the cap of the stopper.
How does a push pop up drain work?
A pop-up drain assembly is a drain that gives you an option to seal your drain to hold water by simply pushing on it to close and to open. Pop-up drains are designed to come in two different options “with overflow” or ”without overflow” openings. They are simple to use and quick to install.
What is the phone number for drainage in Michigan?
For drainage systems in southeastern Michigan, give us a call at 248-505-3065.
Is EZ drain a weak pipe?
I am going to go over a few tips right here for you for when installing EZ Drain by NDS. I don’t recommend what they sell at The Home Depot. It’s a really weak pipe. It’s actually the weakest pipe that I’ve ever seen, to be honest with you.
Where to insert pivot rod in drain?from thespruce.com
Insert the pivot rod into the opening in the side of the tailpiece from under the sink. Usually, there is a plastic washer on each side of the plastic ball. You should be able to feel the tip of the pivot rod slide through the opening in the stopper linkage inside the drain assembly.
How to tighten a drain nut?from thespruce.com
Tighten the mounting nut with channel-type pliers while continuing to hold the tailpiece in place. Do not over-tighten this nut, but make sure it is secure enough so that the drain assembly does not spin in the drain opening.
How does a drain stopper work?from thespruce.com
For most bathroom sinks, the drain stopper apparatus is a pop-up assembly that works by means of a small vertical rod attached to a pivot rod below the sink. This lift rod slides up and down through a small hole in the back of the faucet body. The pivot rod moves a linkage inside the drain tailpiece, lifting or lowering the stopper as needed.
Why is my pop up assembly hard to move?from thespruce.com
If the pop-up assembly is hard to move when you move the pivot rod, it's likely that the pivot rod nut has been tightened down too much and needs to be slightly loosened.
What to use on a pop up sink?from thespruce.com
If you do not have plumber's putty or cannot use it on your type of sink, then you can use silicone caulk. Some pop-up assemblies come with a foam or rubber gasket to use in place of plumber's putty or caulk.
How to connect a vertical strap to a horizontal pivot rod?from thespruce.com
Connect the vertical strap to the horizontal pivot rod by threading the spring clip onto the rod; one end of the clip attaches on each side of the strap.
What to use in place of plumber's putty?from thespruce.com
Some pop-up assemblies come with a foam or rubber gasket to use in place of plumber's putty or caulk. Scoop out a ball of plumber's putty and roll it in your hand to form a long rope, then lay the rope around the edge of the drain ring. Aaron Stickley.
What is the phone number for drainage in Michigan?
For drainage systems in southeastern Michigan, give us a call at 248-505-3065.
Is EZ drain a weak pipe?
I am going to go over a few tips right here for you for when installing EZ Drain by NDS. I don’t recommend what they sell at The Home Depot. It’s a really weak pipe. It’s actually the weakest pipe that I’ve ever seen, to be honest with you.
