INSTALLING AN MP ROTATOR:
- Pull up the body riser using the grey tab and hold in raised position, remove the tab by unscrewing in a counter clockwise direction.
- Screw on the MP Rotator by turning clockwise until hand tight. Do not use pliers as over tightening can damage the nozzle.
- Install the MP Rotator with the Left Edge Indicator pointing to the left side of the desired watering pattern.
How do you install a Hunter Pro sprayer MP Rotator?
Install the MP Rotator with the Left Edge Indicator (flat side of nozzle) pointing to the left side of the desired watering pattern. The Hunter Pro-Spray two piece ratcheting riser will allow you to align the riser by twisting in either direction after MP Rotator is tightened.
What adjustments can be made on an MP Rotator?
There are two adjustments, arc and radius, that can be made on an MP Rotator. Arc: The degrees of coverage of a sprinkler from one side of pattern to the other. A 90-degree arc would be a quarter-circle sprinkler. In other words, how far to the left and to the right the sprinkler will be adjusted to rotate.
What type of body do Hunter MP rotators fit on?
Hunter MP Rotators fit on a traditional pop-up or fixed spray body. The most common bodies are the female threaded version. MP Rotators are also available in a male thread version if needed.
Where can I find the MP Rotator application guide?
1940 Diamond Street / San Marcos, CA 92078 U.S.A. / Tel: (1) 760-744-5240 / Fax: (1) 760-744-7461 / [email protected] / www.mprotator.com MP rotator Landscape Application Guide for Specifiers Specify This Guide includes: 1. MP Rotator Application 2. MP Rotator Models & Performance information 3.
How to install MP rotator?
What is Hunter MP rotator?
How to replace spray nozzle with MP rotator?
Can you mix spray nozzles with MP rotators?
Do Hunter MP rotators have to be head to head?
See 2 more
About this website
Can I adjust MP Rotator without tool?
This MP Rotator Tool is used to adjust both the arc and the radius of MP Rotators. Please note, this tool is not required for adjustments. All adjustments can be made by hand. First, install the MP Rotator with the left edge indicator pointing to the left side of the desired watering pattern.
How do you use the MP Rotator?
5:167:21MP Rotator Sprinkler Overview - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn all MP rotator models rotate the screw clockwise to decrease radius. Or counterclockwise toMoreOn all MP rotator models rotate the screw clockwise to decrease radius. Or counterclockwise to increase radius.
How long should I run MP rotators?
I recommend 60 minutes per rotor zone running 2 days per week, and that should replace that 1" of water lost from evaporation.
How much psi do MP rotators need?
40 psiPressure To achieve maximum radius with an MP Rotator, pressures must be 40 psi or greater.
How do I fix my Hunter MP Rotator?
0:241:52How to fix or adjust the Hunter MP Rotator sprinkler Nozzle - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so on the very top you'll see that there's a small screw. It's very small and it's hard to seeMoreTool so on the very top you'll see that there's a small screw. It's very small and it's hard to see but you'll be able to feel your tool engage the screw. So if you need to reduce.
How many MP rotators are on a zone?
The standard MP Rotators have a matched precipitation rate of approximately 0.4 in/hr. This means any standard MP Rotator at any arc or radius can be placed on the same zone....Customer Type:Body ColorBlackGreyRadius (ft.)8-356-16Warranty3 Years3 YearsFEATURESArc45-36090-36016 more rows
How far do MP rotators spray?
MP ROTATOR DESIGN GUIDE The MP800SR delivers water to distances as small as 6' at a matched precipitation rate of approximately 0.8 in/hr, less than half that of traditional spray nozzles. PRS40 Pair with Pro-Spray® PRS40 for optimal performance. PRS30 Pair with Pro-Spray® PRS30 to achieve minimum 6 ft radius.
What does MP Rotator stand for?
Matched PrecipitationMP stands for Matched Precipitation. An MP rotator is water saving irrigation equipment that converts spray heads easily. MP rotators reduce water use while making the irrigation systems more efficient. MP Rotator Sprinkler Heads. Reduce Your Use!
How much water do MP rotators put out?
Water is delivered at 10 mm/hr with the standard MP Rotator and 20 mm/hr with the MP800 Series, more closely matching what typical soils can absorb. Due to the lack of uniformity, overwatering is the only way to ensure that the driest areas get enough water to keep the landscape green.
Do MP rotators save water?
The MP Rotator's unique design with multiple rotating streams is the world's most efficient sprinkler nozzle with up to 30% water savings vs. traditional sprinklers.
Why do MP rotators stop turning?
If your MP Rotator nozzle is not rotating, the MP Rotator may have some debris in the nozzle. Remove the nozzle to inspect and clean the filter screen. Replace the nozzle and turn the valve on to run sprinklers.
How long should I run my hunter sprinklers?
Typically, you will want 10-13 minutes of run time in the spring and fall, and anywhere from 12 to 17 minutes of run time in the summertime. For flower beds, you will want to use double that amount of time if you are using a drip system, or half if you have a spray system.
How many sprinkler heads should be on a zone?
If your home's water capacity was 10 GPM, you could place 3 heads per zone.
Can you mix rotary and spray sprinklers?
Never Mix. One thing you want to remember is that you don't want to mix these all on the same irrigation zone. That's because there are the different precipitation rates we talked about. Remember, the spray heads here have a precipitation rate that's two to three times more than your rotors or your rotary nozzles.
Why is my hunter sprinkler head not rotating?
The most common reason for a sprinkler to stop rotating is the accumulation of debris in the filter. This video will teach you how to clean the filter on your rotors. Hunter rotary sprinklers operate on a “gear drive” system.
How do I clean my MP Rotator filter?
1:021:49How To Clean A Sprinkler Filter - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the nozzle off. And pull your filter out in this case we've got some debris in the filter. We'MoreTake the nozzle off. And pull your filter out in this case we've got some debris in the filter. We'll use our water to go ahead and wash that. Out. You can also spray that out with a garden hose.
How do you adjust the distance on a sprinkler head?
0:091:06How to Adjust the Distance on Rain Bird Rotor Sprinklers - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a flat bladed screwdriver. Turn the radius reduction screw here at the point of the largeMoreUsing a flat bladed screwdriver. Turn the radius reduction screw here at the point of the large arrow. I can to find where the water comes out to decrease the spray distance up to 25%.
How do you adjust the distance on an MP Rotator?
0:481:48How to Adjust Hunter's MP Rotator - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn all MP rotator models rotate the screw clockwise to decrease radius. Or counter clockwise toMoreOn all MP rotator models rotate the screw clockwise to decrease radius. Or counter clockwise to increase radius.
How many sprinklers can I run at once?
This will primarily be determined by the total flow rate and pressure you have available at your source. For example, you generally have a flow rate of 10 gpm from a ¾-inch spigot where you connect your hose. With your 10 gpm flow rate at your spigot, you could run two sprinklers at 5 gpm each.
How do I know what sprinkler zone to use?
Draw Your Sprinkler Zone Plan With simple math, you can determine how many heads in each zone and then take the total number of sprinklers you need, and divide that by your head/zone number and that will tell you how many zones you need.
Why do MP rotators stop turning?
If your MP Rotator nozzle is not rotating, the MP Rotator may have some debris in the nozzle. Remove the nozzle to inspect and clean the filter screen. Replace the nozzle and turn the valve on to run sprinklers.
How do you adjust a rotating sprinkler?
0:001:51Adjusting Rotary Type Sprinkler Heads | Massey Services - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse the radius adjustment. Finally you'll need to adjust the distance of the spray. To do this turnMoreUse the radius adjustment. Finally you'll need to adjust the distance of the spray. To do this turn the adjustment screw clockwise until it's touching the water stream.
How many sprinkler heads should be on a zone?
If your home's water capacity was 10 GPM, you could place 3 heads per zone.
How do you adjust Rainbird rotating sprinkler heads?
1:051:59How To Adjust A Rain Bird 5000 Series Rotor - YouTubeYouTubeStart of suggested clipEnd of suggested clipStop insert the tool into the arc adjustment hole until it seats then turn the tool in theMoreStop insert the tool into the arc adjustment hole until it seats then turn the tool in the appropriate. Direction clockwise to increase the arc. And counterclockwise to decrease.
Switching from Hunter PGP's to MP Rotators for the Lawn - The Lawn Forum
Greetings, I picked up 6 of the Hunter MP3500's and 6 PRS40 (pressure regulated)bodies couple of days ago. While swapping the bodies (replacing the Hunter PGP's), found that there was no moisture in the clay soil that I dug up.
MP ROTATOR 8' to 35' 0 - Hunter Industries
MP OTATOR Visit hunterindustries.com MP ROTATOR® Radius: 8' to 35' KEY BENEFITS •ow precipitation rate of approximately 0.4 in/hr — lowest in the industry L • Automatic matched precipitation for simplified irrigation design and flexibility
Yahoo
Best in class Yahoo Mail, breaking local, national and global news, finance, sports, music, movies... You get more out of the web, you get more out of life.
How to install MP rotator?
Install the MP Rotator with the Left Edge Indicator (flat side of nozzle) pointing to the left side of the desired watering pattern. The Hunter Pro-Spray two piece ratcheting riser will allow you to align the riser by twisting in either direction after MP Rotator is tightened.
How to adjust MP rotator?
MP Rotator - Adjusting the Radius and Arc 1 Install the MP Rotator with the Left Edge Indicator (flat side of nozzle) pointing to the left side of the desired watering pattern. The Hunter Pro-Spray two piece ratcheting riser will allow you to align the riser by twisting in either direction after MP Rotator is tightened. 2 With the MP Rotator operating and in the pop-up position, rotate the Arc Adjustment Ring. Turning the Arc Adjustment Ring clockwise will increase the arc, counter clockwise will decrease the arc.
Which way to turn arc adjustment ring?
Turning the Arc Adjustment Ring clockwise will increase the arc, counter clockwise will decrease the arc. Note: Adjustment can be done with the MP Rotator Tool (MPTOOL) or by hand.
Does MP rotator shut off?
To prevent damage during adjustment, the MP Rotator does not completely shut off like a spray nozzle. To achieve maximum radius reduction with any MP Rotator model use a 30 PSI (2 BAR) regulating spray body.
Why use MP rotator?
Because the MP Rotator applies less water with increased uniformity, simply doubling the run time used for traditional spray nozzles may supply sufficient water to the landscape while using less water overall.
What is MP corner?
The MP Corner is specially designed to provide extra coverage in tight corners so that neighboring heads do not need to reach into the corner to provide head-to-head coverage , avoiding unnecessary overspray onto non- target areas.
What is the precipitation rate of MP800SR?
With a precipitation rate of approximately 0.8 in/hr, it is strongly suggested to zone the MP800SR separately to maintain matched precipita- tion within each zone. Radius Arc 90° to 210° 360° 6' to 12'
What is the best filter for a MP800SR?
Filtration Guidelines It is recommended to use primary filtration when operating with dirty water. A general rule is to use primary filtration that is five times the mesh rating of the nozzle filter. For example, if the nozzle filter is 20 mesh, the primary filter should be 100 mesh. Field testing has shown that the MP800SR runs well in dirty water conditions with the use of a 150 mesh primary filtration system.
Hunter MP Rotators
What is everyones thoughts on the Hunter MP Rotators? Im in the middle of a renovation of my front lawn but plan on putting an irrigation system in this fall or next spring. I would like to get it done in the fall because im planning on renovating the back yard next spring. I have a roughly 8,500 sqft lawn.
Re: Hunter MP Rotators
I have them in one of my zones that is relatively narrow simply because the PGP Ultra's minimum radius is too large. The Rotators seem fine for my application, but I'd be concerned about their smaller streams at longer distances.
Re: Hunter MP Rotators
Pro: easier to adjust than spray heads (honestly gear rotors too) and more efficient than spray heads. Probably better uniformity than gear rotors but I can't say this with 100% certainty. Probably more intuitive for DIYers, because you don't have to swap nozzles for different flow depending on the arc like gear rotors.
Re: Hunter MP Rotators
I love mine. This was my first irrigation install, so it's taken me a while to dial them in for even coverage. But I am proud that I only made two big goofs. I have two challenging little areas and they stay bone dry. But I have plans to tweak things a bit to water these areas correctly. No big deal.
How to remove a body riser?
Pull up the body riser using the grey tab and hold in raised position, remove the tab by unscrewing in a counter clockwise direction.
What is MP nozzle?
As the most popular popup nozzle in the Hunter range, the MP Rotator nozzles feature unique, multi-trajectory rotating streams that deliver water at a steady rate to allow water to gently soak in at rates that soils can absorb.
How to install MP rotator?
To Install MP Rotator, screw on the MP Rotator by turning clock wise till hand tight. Install the MP Rotator with the Left Edge Indicator pointing to the left side of the desired watering pattern. Note: Ensure no debris gets in the body well replacing nozzle.
What is Hunter MP rotator?
Hunter MP Rotators fit on a traditional pop-up or fixed spray body. The most common bodies are the female threaded version. MP Rotators are also available in a male thread version if needed. MP Rotators make a great replacement for spray nozzles adding the benefit of being a much more efficient nozzle with low preciperation and matched uniformity.
How to replace spray nozzle with MP rotator?
Remember: When replacing spray nozzles with MP Rotator you will need to at least double your run time, which will still save you about 30% more water than spray nozzles. Pull up the body riser and hold in raised position. Remove the current spray nozzle by holding the body and unscrewing counter clockwise.
Can you mix spray nozzles with MP rotators?
Warning: Do not mix Spray Nozzles with MP Rotators on the same zone. MP Rotators have a much lower application rate of water and should run longer, if a spray is on the same zone it will severely overwater in it location.
Do Hunter MP rotators have to be head to head?
Hunter MP rotators should be designed with head to head spacing for optimal performance. Warning: If your nozzles are not covering the desired distance, you may need to move up to a longer arc nozzle. Warning: Do not mix Spray Nozzles with MP Rotators on the same zone.
