Installing Your Livewell or Baitwell
- Adjust the lid twist locks to the desired tension.
- Attach air hose firmly to the back of the black Air Control
- Run pump leads though the hole next to the Air Control Center. ...
- Attach copper and s/s electrical clips to the wires.
- Tanks with installed Hold Down Plates for Infusers on bottom of tank.
How to install a livewell or bait well on a boat?
This Livewell or Bait Well setup is easy to install. As you can see by the diagram the overflow outlets directly through the hull of the boat above the water line allowing you to refresh and recirculate the water in your livewell or bait well tank. This design is best if you are doing a horizontal mount livewell.
What size pump do I need for my livewell?
Pump would depend on the gallon size and number of Livewells and Bait Wells you will have installed in your boat. This Livewell or Bait Well setup is simple and easy.
Do I need a live well pump on my Boat?
This will allow fish to remain healthy while the standard live well pump is off when the boat is in contaminated water, or when the pump is air-locked. Many boats have the live well pump installed on the transom.
How do I refresh the water in my livewell?
As you can see by the diagram the overflow "T's" into the drain line allowing you to refresh and recirculate the water in your livewell or bait well tank. This design is best if you are doing a side mount livewell or if you don't want to drill an above waterline hole in your boat.
How do you install a livewell pump?
5:4017:31How to Install or Replace a Livewell Aerator Pump in Your Boat!YouTubeStart of suggested clipEnd of suggested clipAnd we need to cut the power wire. And splice in the new one all right so just so you get a betterMoreAnd we need to cut the power wire. And splice in the new one all right so just so you get a better idea of what this looks like this is the actual aerator pump. And you can see you've got the flange.
How do you plumb a livewell pump?
18:2432:55Livewell Plumbing Installation Tutorial 2021 - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor all the water to come in and enter the pump the hosing all that good stuff. This is the through-MoreFor all the water to come in and enter the pump the hosing all that good stuff. This is the through-hole fitting that we're going to be using for that application as you can see this thing breaks.
How do you install a livewell pump on a jon boat?
1:2812:24How To Install A Livewell Pump In A Jon Boat - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you need to be about 2 inches or so below the waterline drill important that way when you standMoreAnd you need to be about 2 inches or so below the waterline drill important that way when you stand in the boat. Your intake valve is the waterline so you can suck in sucking water from the lake.
Can you use a bilge pump for a livewell?
Install a Pump Box Bilge pumps work here because they use the same motors and impellers as in centrifugal livewell pumps.
How does livewell pump out work?
1:538:23Ranger RT188 Livewell Controls EXPLAINED (Pump In ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt closes the drain valve. So this water will not go out of your live well so if you want to fillMoreIt closes the drain valve. So this water will not go out of your live well so if you want to fill your live well. Up you put it on auto. And you take your switch right here your rear aerator switch.
Where does my livewell drain?
You can take a look at the livewell pump to see how it's plumbed, but the livewell will probably drain out back through the pump when it's out of the water. There could possibly be a valve inline to turn off flow through the drain/fill hose near the pump also, but you'll see it when you look at the pump.
How do you put a livewell in a boat?
1:0610:39Make your own Tourney-grade Livewell | TBNation - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere we are with the top box we cut out a lid for our splash guard. We are using a lot of 3/4MoreHere we are with the top box we cut out a lid for our splash guard. We are using a lot of 3/4 braided flex hosing Center through hole fittings clamps.
Why is my livewell not pumping water?
If you hear the pump running, it may be worn out, and unable to pump water because the impeller is too worn. Just to be sure, check and make sure there's no crossover switch that's on recirculate, instead of auto fill. There might also be some debris in the pump. They are easy to remove and check.
How do you replace a bilge pump on a boat?
0:263:57DIY Automatic Bilge Pump Installation or Replacement | BoatUS - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the first thing I need to do is unscrew the hose from the pump. You'll notice here that on thisMoreSo the first thing I need to do is unscrew the hose from the pump. You'll notice here that on this pump I've actually got a golden hose fitting. So I can just unscrew that.
Are livewell pumps submersible?
Pump is fully submersible and utilizes tin-coated, 16-gauge wire for safety. Extremely efficient, very low current draw and offer high capacity output.
Is a aerator pump same as a live well pump?
A re-circulation pump recirculates the water inside your live well. Some people also call this an aerator... re-circulation adds air into the water. They are the same thing just call it which ever one you want too.
How long does a live well pump last?
Depending on the equipment type and model, well pumps typically last anywhere from 8 to 15 years. However, several factors can contribute to the premature expiration of a well pump.
How to clean a KeepAlive oxygen regulator?
If your KeepAlive Oxygen Regulator is accidentally immersed in salt water, remove the red dust cover from the safety relief valve, flush well with fresh water, and let dry before using again.
What is a two pump boat?
A two pump system is the preferred system of boat builders wanting to provide a superior livewell. A simple two pump system provides a back-up in the event of pump failure.
How to turn on oxygen cylinder?
Before turning on the oxygen cylinder valve, check to be sure that the regulator is in the “0” position. 2. Stand behind the cylinder so that the cylinder is between you and the regulator. Remember: Never stand in front of a cylinder outlet or regulator when opening the cylinder valve.
Can a boat be trailered with a live well pump?
When the boat is on a plane, the intake of the pump is out of the water and is ineffective. The boat can also be trailered while the bait remains in the live well. This system always remains on while fish are in the well. ONE PUMP INSTALLATION.
Does KeepAlive work in salt water?
KeepAlive, operating in salt water, provides a much more dramatic VISUAL display than fresh water. To ensure that your Infusor is operating properly, LISTEN for the sound of air at the Air Control Valve. IN FRESH WATER, the Infusor produces many sizes of bubbles.