When installing the starter strip, you wanna put five nails in each starter strip. Owens Corning recommends 2 to 3 inches back from the edge of the roof. And they recommend five nails, so it’s gonna be one on each end, and then three placed evenly across.
What are starter strip shingles?
Starter Strip Shingles eliminate the need for cutting shingle tabs to create a starter row. Starter Strip is packaged two pieces per shingle, 16 shingles per bundle, 100 lineal feet, and perforated down the center allowing for easy separation.
How do you use a starter strip on a Camelot shingle?
For such applications; begin by separating the strip at the perforated line. When applying shingles with exposures greater than 6 inches, such as the Camelot collection, only full un-split WeatherBlocker starter strip can be used. Place the appropriate sized starter strip with the sealant facing up at the eave edge.
How do you install a starter strip on a roof?
For maximum wind resistance, starter strips should be installed along all rake edges. Begin by laying the strip with the sealant side up, closest to the rake edge. Position the starter strip so that it overlaps the eave starter strip by at least three inches.
How much overhang do you need for a starter strip?
For proper water drainage, Both Pro-Start and Weatherblocker starter strip require a one quarter to three quarter inches overhang at all eave and rake edges. Every Starter strip requires a minimum of four nails driven in a linear fashion one and a half to three inches above the shingle's bottom edge.
See more
How do you install starter strips?
2:303:53How to Install Starter Strip Roofing Shingles | Mastering the Roof by GAFYouTubeStart of suggested clipEnd of suggested clipPosition the starter strip. So that it overlaps the eave starter strip by at least three inches asMorePosition the starter strip. So that it overlaps the eave starter strip by at least three inches as with the eave edges. The starter strip must overhang the rake edge 1/4 to 3/4 of an inch.
Which way does a starter strip go shingles?
0:286:00How to Install Starter Shingles - YouTubeYouTubeStart of suggested clipEnd of suggested clipStrips. Some contractors will opt out of using actual starter shingles and they will use a three topMoreStrips. Some contractors will opt out of using actual starter shingles and they will use a three top shingle or even their architectural shingles that they're installing on your roof.
How do you install Owens Corning starter shingles?
Simply apply a single course of Starter Shingle Roll along a clean, dry and smooth eave line, after removing the release sheet. Apply the Starter Shingle Roll directly onto the WeatherLock® underlayment or a layer of felt. Once it is pressed into place, you're ready to begin shingling.
How do you install a starter course for shingles?
1:096:32HOW TO INSTALL THE STARTER SHINGLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to stall this signal the starter strip shingles around the parameter. Right here is theMoreWe're going to stall this signal the starter strip shingles around the parameter. Right here is the eave. And five nails per single right above the glue line right above the asphalt a sealant.
Does starter strip go on the rakes?
Where do they go? Historically, starter strip shingles have been used not only at the lower eave edge of the roof, but experienced professionals also use them at the gable, or rake edges of roofs.
Do you overlap starter shingles?
0:242:34ESSENTIALS OF THE STARTER SHINGLE - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight here 3/4 inch is good but what we do not want to do is I don't want to make it shorter thanMoreRight here 3/4 inch is good but what we do not want to do is I don't want to make it shorter than that 1/2 inch would be would be okay no the other thing is we do not want to make it longer than an
How do you use a 3 tab shingle starter strip?
0:000:30Common Mistake: Substituting Cut 3-Tab Shingles For Starter StripsYouTubeStart of suggested clipEnd of suggested clipStrips. Remember the edge of the starter shingles should hang over a roof edge or drip edge betweenMoreStrips. Remember the edge of the starter shingles should hang over a roof edge or drip edge between 1/4. And 3/4 of an inch. Find GAF starter shingles at the home depot.
What is the plastic strip on the back of shingles?
What Is That Shiny Plastic Film Strip On Shingles? Sealant protection… GAF adds a thin plastic film to keep the sealant from activating while in storage and shipping. This film is protecting the shingles from sealing together while in storage but does not align with the sealant adhesive when the shingles are installed.
How do you start the first row of three tab shingles?
0:244:56How to : Roofing - Where to start laying (three) 3 tab shingles / starter ...YouTubeStart of suggested clipEnd of suggested clipSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab offMoreSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab off boat. So we want it flipped upside down lined up on a thirty inch mark.
Does starter strip go over drip edge?
After installing drip-edge along the eaves, double the first course of shingles or, as shown, install a starter strip. The lower edge of the starter strip overhangs the drip-edge by 1⁄4 in. to 3⁄4 in. —or even 1 in. if bowing eaves or rake boards require it.
What length should I cut my starter shingles?
Cut 12 inches (30.4 centimeters) off the length of the first shingle that you lay. Then lay down whole tiles to the end of the row, trimming the last shingle so that it fits correctly. Continue laying and nailing down shingles in this manner.
How do you use a 3 tab shingle starter strip?
0:000:30Common Mistake: Substituting Cut 3-Tab Shingles For Starter StripsYouTubeStart of suggested clipEnd of suggested clipStrips. Remember the edge of the starter shingles should hang over a roof edge or drip edge betweenMoreStrips. Remember the edge of the starter shingles should hang over a roof edge or drip edge between 1/4. And 3/4 of an inch. Find GAF starter shingles at the home depot.
How do you start the first row of three tab shingles?
0:244:56How to : Roofing - Where to start laying (three) 3 tab shingles / starter ...YouTubeStart of suggested clipEnd of suggested clipSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab offMoreSo after this one here is nailed in place then you say how I line it up. So we've cut a half tab off boat. So we want it flipped upside down lined up on a thirty inch mark.
What is the plastic strip on the back of shingles?
What Is That Shiny Plastic Film Strip On Shingles? Sealant protection… GAF adds a thin plastic film to keep the sealant from activating while in storage and shipping. This film is protecting the shingles from sealing together while in storage but does not align with the sealant adhesive when the shingles are installed.
How many square inches of intake for Owens Corning roof?
9. For each Roof Mount fan, Owens Corning Roofing requires 600 square inches of intake. See instructions for details.
How does starter strip plus shingle work?
Starter Strip Plus Shingle helps save time by eliminating the need to cut shingles to create a starter row. Starter Strip Plus Shingle is packaged two pieces per shingle, and perforated down the center for easy separation.
Is Owens Corning a global company?
Even though we’re a global company, we ’re always ready to answer your questions. Call to speak with an Owens Corning representative so you can start your project right away.
