Knowledge Builders

how do i install staggered shiplap

by Maddison Legros Published 1 year ago Updated 2 months ago
image

  1. Measure and cut the shiplap board to fit the wall. ...
  2. Stagger shiplap boards on a wide wall. If the width of your wall exceeds the length of your shiplap, you’ll need to stagger boards by butting 2 boards together.
  3. Squeeze a line of Heavy Adhesive paste along the back of the shiplap board. Do this immediately before you attach the shiplap to the wall.
  4. Set the board against the wall and check that it’s level. The adhesive will hold the shiplap firmly against the wall, so don’t nail it in place yet.
  5. Nail or screw the shiplap to the wall. You can do this using a hammer, a compressed-air nail gun, or a screw gun.

Stagger the shiplap boards so that the end joints are spread out along the wall or ceiling randomly. If you stack seams on top of each other, you'll create an eyesore that draws your eye to the dark lines of the jointed ends. Building pros agree that staggering seams provides a better looking aesthetic.Jan 16, 2021

Full Answer

How do you stagger a shiplap wall?

If the width of your wall exceeds the length of your shiplap, you’ll need to stagger boards by butting 2 boards together. Measure and cut the second (shorter) board to correctly fill the gap between the end of the first board the wall.

Should shiplap be staggered?

Staggering Shiplap Creates A Balanced Aesthetic When installing shiplap on a wall or ceiling that exceeds the length of your shiplap, you’ll need to butt boards together. Stagger the shiplap boards so that the end joints are spread out along the wall or ceiling randomly.

How do you install shiplap from the top down?

If you’re installing shiplap from the top of the wall down, you’ll need to carefully hold the nickels in place on the bottom of the board as you line up the next plank. Alternatively, you could use scrap plexiglass pieces cut into strips, stacked to the desired thickness, and glued together as spacers.

How do you finish shiplap boards?

You can always use caulk to cover up any small mistakes. As you put up a run of shiplap and you encounter an electrical box, place the board over the box and use a pencil to trace its outline onto the board. Use a jigsaw to make your cuts. Once you’ve installed all your shiplap boards, you'll have some finishing touches to add.

image

How do you join two pieces of shiplap?

1:343:23How to Install Shiplap | The Home Depot - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut the boards to fit at the beginning or end of a row if necessary. If two boards meet at the sameMoreCut the boards to fit at the beginning or end of a row if necessary. If two boards meet at the same stud. Position the first piece halfway onto the stud and install.

When installing shiplap do you start at the bottom or top?

bottomThe first key to installing shiplap is to always, always, always start at the bottom of your wall! This little piece of advice is actually good for two very important reasons. First, by starting at the bottom, it allows gravity to be a helpful aid as you work your way up the walls.

Do you overlap shiplap?

Stagger Cuts Start the next piece on the same stud. Cut to fit if necessary. Repeat until you reach the end of the row. Never overlap boards.

Does shiplap have to end on stud?

The answer is yes. The advantage of installing shiplap directly to the studs is that you save yourself the hassle of having to find the studs. Make sure your boards are level and then use a brad nailer to nail it to the stud. Continue this process until all boards are securely fastened.

Do you put trim around shiplap?

Trim Shiplap Edges Another way to finish shiplap edges is to use a trim. Trim is a great way to cover up any gaps and can be used to create a more polished look on any accent wall. It's perfect for adding the finishing touch, so it's definitely something you should consider using if you want a well-finished look.

Do you face nail shiplap?

We always recommend face nailing shiplap and tongue and groove when installing it on your walls, ceiling, and as exterior siding. Face nailing means that you shoot your nail at a 90 degree angle to the board through the flat (or face) of the board.

How do you hide seams in shiplap?

How To Caulk Seams On ShiplapOnce you have installed your shiplap, run a bead of acrylic caulk (also known as latex caulk) along the seams where the shiplap ends butt up to a wall, inside corner or molding.Smooth out the caulk with a clean finger or rag so that the caulk fits neatly into the seam.More items...•

How do I arrange shiplap?

0:352:26Measuring & Staggering Shiplap - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace. It against the wall. All. The way on the side we put a popsicle stick up against the wallMorePlace. It against the wall. All. The way on the side we put a popsicle stick up against the wall because that's what we use to stay for for it's just a blip popsicle stick.

How do you stagger cladding?

3:416:52Staggering the plank walls. - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere. Then I fill in with a Miller piece a long piece. And come off the camera over here. We're notMoreHere. Then I fill in with a Miller piece a long piece. And come off the camera over here. We're not going to worry about this side of the wall because you'll get that you'll get the principle of it.

Should shiplap be installed over drywall?

You can install shiplap right over the drywall. However—and this part is crucial—you must first take the time to find all the studs within your walls and mark them carefully before you place a single board.

Should you glue shiplap to drywall?

Shiplap can be installed directly to sheet rock/drywall. Simply mark the stud locations for nailing the shiplap or you can apply a construction adhesive such as liquid nails.

How long should nails be for shiplap?

1-½” to 2”We recommend using 16- or 18-gauge finish or brad nails. 1-½” to 2” in length should be sufficient. Both gauges are strong enough to hold the lumber securely, but small enough as to not leave a large hole on the face of the board. Go ahead and buy the bulk pack: you're going to need it!

What is shiplap?

Shiplap is basically a shingled siding. It's horizontal boards, and each board overlaps the one below it—much like the shingles on a roof. It's usu...

How much should you overlap the boards?

That depends on the dimension of the board. If your boards are 8 or 10 inches wide, you might do 1-2 inches of overlap. If your boards are smaller,...

Where do you put the nails in shiplap boards?

You want to fasten each board in the area that's going to be covered by the board above it. You don't want to run nails or screws through an expose...

How to measure shiplap?

Using a tape measure, measure the wall on which you’ll be installing shiplap boards from one side to the other. Then, use the tape measure to measure the same distance on each of your shiplap boards. Mark the distance with a pencil.

What is shiplap siding?

Shiplap is a distinctive type of siding which is formed from long, horizontally stacked boards. This siding was initially used on the sides of wooden ships to keep them watertight. Shiplap is currently used for decorative purposes indoors, as its stacked boards create a distinctive visual effect.

How wide is a shiplap wall?

For example, if your wall is 20 feet (6.1 m) wide and your shiplap siding is only 15 feet (4.6 m), you’ll need to cut an additional 5 ft (1.5 m) section of shiplap to finish the row. Even if your boards would fully span the width of your wall, consider staggering your shiplap anyway.

How to raise a board that is not horizontally level?

If the board is not horizontally level, you’ll need to lift out the board, then install spacers beneath the low side to elevate it .

Do you remove shiplap before installing baseboards?

If the wall that you’re applying shiplap to has baseboard molding at the bottom, remove this before you install the shiplap so the baseboards aren’t scratched. Be careful that the lowest shiplap board aligns precisely with the top of the baseboard.

Please inspect the planks prior to instillation. Contact customer service before installing if there are any cosmetic concerns. Read Instructions thoroughly before beginning installation. Instructions must be followed in order for warranty to remain effective

In order to insure proper adhesion and to avoid future movement such as gapping between boards and cracking on the face of the planks, permanent HVAC must be on and maintained between 60 ̊ - 75 ̊ F with a relative humidity in the home between 30-55% for a minimum of 14 days prior to installation as well as during and after installation.

1. Clean and dry the surface

Turn off power to installation area while working around wall outlets and light switches. Remove electrical cover plates, protruding nails and loose paint.

2. "Dry Lay" the planks

Work from several open boxes and “dry lay” before permanently installing to create your desired look. Working from several open cartons, lay them in an open area according to your desired aesthetic and preferred staggered sequence.

3. Adding trim pieces

For walls that have outside corners, a trim piece may need to be purchased separately to create a finished look. If trim pieces are needed on your project, measure 1 3⁄4" back from where you wish the wall to end and then draw a vertical plumb line using your level. This line will be your guide to where the planks need to be cut.

4. Establish your starting line

There are multiple ways you can establish your starting line. The most important aspect of establishing your starting line is to ensure that the first row of planks you install is 100% level. If your baseboard and ceiling are level, you can use one or the other to establish your starting line.

5. Applying the planks

Starting on the left side of the room, and using the starting line (and nails) as a guide, peel the paper off the VacuuBond™ adhesive and position the starter row planks groove side up, along your line. Press into place and immediately use the J-Roller over the plank surface.

6. Stagger the planks

Now that your level starter row is in place, stagger the end joints as you work your way up and down the wall, so that your end joints do not match up from row to row. To accomplish this look and minimize your waste, use your cut off piece from one row to start the next row.

What do you need to know about shiplap?

All You Need to Know About Shiplap. Shiplap can add rustic charm to any blank wall. Learn more about the trendy wooden planks and how you can install them in your own home. Shiplap has been popping up everywhere lately. The rough-sawn wooden planks arranged as horizontal panels can take any wall from drab to dramatic.

How long is a shiplap board?

This cut will give you exactly eight 8-foot-long boards from every sheet of plywood (because the saw eats ⅛ inch with every cut).

What is shiplap used for?

Until the advent of plywood, shiplap boards were commonly used to construct the sheathing between a home’s structural framing and its exterior siding. Nowadays, people often find shiplap sheathing underneath the wood siding of historic homes during exterior renovation projects.

Is shiplap a functional material?

When used indoors, shiplap shifts from functional to purely aesthetic. The wood panels add visual character and texture to otherwise blank walls in a home, and have the ability to adapt to any decorative scheme, depending on how the homeowner chooses to incorporate the material.

Do I need a carpenter to install shiplap?

Installing Shiplap. While you don’t need to be a professional carpenter to install shiplap paneling at home, you should be familiar with basic woodworking skills like measuring, sawing, and nailing. The most common (and affordable) way to re-create a shiplap look from scratch is to use plywood.

Can you put shiplap on a wall?

No matter your home’s style, installing shiplap paneling on one or more walls will enhance your decor. For more adventurous designers, shiplap can go beyond standard wall coverings. Consider installing it as wainscoting, or use it to cover the backs of built-in cubbies or bookcases.

How do I install shiplap?

Installing Shiplap: Cut Strips. Set your table saw to the desired width and don’t forget your safety glasses. Large sheets of plywood are dangerous to cut by yourself on a table saw. Get a friend to help hold the plywood as you move it through the saw.

How do I install a board on a wall?

Place your first board along the edge of the floor and make sure it’s level (Image 1). Use a finish nailer to attach the board to the wall at the location of each stud (Image 2) . Use a nickel as a spacer between every board in a run and between each run (Images 3 and 4). Periodically make sure your boards are level.

How far apart should 2x4 studs be?

Use a stud finder to locate each 2x4 stud in the wall. Use a stud finder to locate each 2x4 stud in the wall. They should be about 16” apart. Use your 4’ level to mark the location of each stud on the wall. Leaving as little waste as possible, you can cut your boards to lengths that match the location of each stud.

How long does it take to install a doorbell?

All you need is three hours and these easy step-by-step instructions. How to Install a Doorbell. Whether your doorbell is broken, unattractive or simply not high-tech enough, it’s an easy fix to replace it with something that’s right for you.

Can you paint shiplap before cutting?

You normally wouldn't start a project by painting, but in this scenario, it’s much easier to paint your plywood shiplap before cutting it. You’ll only need to paint one side of the wood; allow it to fully dry before cutting. Remember to leave that final sheet of plywood unpainted.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9