- Measure the length and width of each stair tread individually. On most staircases, each stair is a slightly different size.
- Cut the tread to the exact size needed using a miter saw. ...
- Number each tread piece on the back side where it will not be seen after installation with the corresponding step number as you cut them.
- Stain the treads to protect the surface of the wood. Leave the stain to dry according to the manufacturer’s directions.
- Set the stair treads in place, testing each to make sure it fits properly. Leave the treads on their respective steps until you are ready to install them.
- Squeeze a bead of polyurethane glue along each stringer that the step will rest on. ...
- Set the stair tread in place and tap the front edge with a rubber mallet to form a bond with the glue and the riser.
- Leave the glue to cure according to the manufacturer’s directions and avoid walking on the stairs until then.
Full Answer
How to install wood stair treads without showing nail holes?
Jun 25, 2021 · When dealing with a metal stringer there are a few different options we offer. You can mortar the treads on, install them using angle brackets, or weld them onto the stringer using weld plates. Empire Precast specializes in stair tread manufacturing so using the dimensions of the stair and your metal stringer we can determine the proper position for the weld plates and …
How do I install trim around stair treads?
Nov 07, 2019 · Easily remodel carpeted stairs to beautiful hardwoodUse a urethane based construction adhesive with RetroTreadsWider cove covers imperfections in existing st...
How to install unfinished oak stair treads?
Measure each tread and cut it to size then install it using 2-1/4' trim screws. installing the treads. Install the Treads. fill in screw holes with wood putty. Fill Screw Holes. mark stair railing for angled cut. Cut Railing to Length. pre drill landing and treads for balusters. attach rail fasteners into newel posts.
How to attach carpet stair treads?
Jul 25, 2021 · Dry-fit each tread before installing. Installing the Stair Treads Individually measure and cut each stair tread to length with a handheld circular saw or sliding miter saw. To make sure you achieve a near perfect fit, I suggest using an angle finder to make sure the treads should indeed be cut at a straight 90 degrees.
Should you nail or screw stair treads?
Don't fasten treads and or risers with only nails or staples. The adhesive is much more important than the fasteners. There will be times when fastening may be limited, so a good adhesive is critical.Sep 28, 2015
How do you install stair treads?
5:048:25Installing Prefinished Stair Treads - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen installing the risers we always want to install the ripped edge up. This way any uneven cutsMoreWhen installing the risers we always want to install the ripped edge up. This way any uneven cuts will be hidden under the nose of the new stair tread and the flat edge will show on top of the tread.
What is the best way to fasten stair treads?
2:574:21Slick Way of Blind Fastening Stair Treads - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn snap it into place make sure you're using a rubber mallet lock lock that in nice tight fit andMoreIn snap it into place make sure you're using a rubber mallet lock lock that in nice tight fit and then you simply take this little screw. Make sure you've got a right angle drill.
How do you install stair treads over existing stairs?
Cut the treads to width with a handheld circular saw or sliding miter saw. Use construction adhesive and finish nails to install the new risers to cover the existing ones. If you're working with thin hardwood risers, then it's a good idea to predrill the nail holes to avoid splitting the wood.
How do you attach wood stair treads?
1:272:47Creak free wood stair treads WITHOUT NAILS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they'll flex a bit what I'm actually aiming. For is this gap here and when this glue is wet I'llMoreAnd they'll flex a bit what I'm actually aiming. For is this gap here and when this glue is wet I'll tighten all the outside screws. That's going to pull the board the tread down. And smash the glue.
How do you glue down wood stair treads?
9:4024:25How to Install Hardwood Stair Treads & Risers...Key Techniques for ...YouTubeStart of suggested clipEnd of suggested clipIf it is I'll trust the adhesive. And the pressure fit. If state the tread has a little bit of aMoreIf it is I'll trust the adhesive. And the pressure fit. If state the tread has a little bit of a twist in it and it wants to raise up off of the riser.
Can you install stair treads without nails?
Modern adhesive technology allows for the installation of stair treads without having to drill holes for screws or hammer nails into the surface. Over time, the staircase will shift as the house settles and nails can work themselves loose, not only leaving an unsightly hole but also creating a safety hazard.
Can you glue down stair treads?
The type product used for gluing stair treads depends on the material of the treads and the risers. The advantages of using adhesive that attach stair treads include reduced use of nails or screws, simple installation and the ability to easily bond most types of surfaces together.Sep 21, 2017
Do you install stair treads or risers first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser. Treads and risers fasten with construction adhesive to the subfloor.
Should you stain stair treads before installation?
Staining and varnishing hardwood treads prior to installation is recommended, especially in this case where we have stone or tile risers. We purchased 11.5-in x 48-in unfinished red oak stair treads from Lowes for about $30 each. Treads should be laid out, sanded if needed, and cleaned prior to applying stain.
How do you fill the gap between stair tread and riser?
Run a heavy bead of the silicone along the gap to fill it, and then use a wet fingertip to smooth it out if necessary. It's the fastest way to fill minor gaps, and if you're not happy with the way it looks, you can always install molding over it.
How much should a stair tread overhang?
The nosing on treads, believe it or not, has a code minimum and maximum of how far the nosing projects over the next stair. Nosings are required to overhang a minimum of ¾-in. to a maximum of 1-¼-in. Also the maximum nosing radius cannot exceed 9/16 of an inch.
Step 1: Measure Each Step
The first thing you'll need to do is measure your steps. Using your tape measure, determine the width and depth (pictured in the image above) of each step. You will need these dimensions when it comes time to shop for your new stair treads.
Step 2: Purchasing Stair Treads
This is the fun part! You can find a variety of stair treads at your local hardware superstore. These safety stair parts come in a variety of materials: metal stair treads, cast concrete stair treads, carpet stair treads, and even glow-in-the-dark stair treads.
Step 3: Installing Your Stair Treads
After you've purchased your new set of stair treads or received them on your doorstep, it's time to officially begin the installation process.
Step 4: Apply Adhesive to Tread Backing
Flip over your first tread or nosing so you are looking at its underside. Using your caulk gun and adhesive, apply a thin line of caulk around each pre-drilled hole, then make a nice squiggle through the middle. For extra security, you can make a caulk outline around the perimeter of the underside as well.
Step 5: Anchor Tread to Stair
Once adhesive has been applied to the tread backing, turn it over and carefully place it in position on your stair. Grab your power drill and the appropriate drill bit (one size smaller than that of your screw or anchor).
Step 6: Complete Your Installation
Repeat the previous instructions until all stairs have been equipped with its own anti-slip tread.
Basic Information
How do I install stair treads? This is a question we hear often and I am here today to answer it for you.
Metal Stringer
When dealing with a metal stringer there are a few different options we offer. You can mortar the treads on, install them using angle brackets, or weld them onto the stringer using weld plates.
Wood Stringer
For a wood stringer the method of installation will be entirely the same as the previously mentioned metal stringer installation steps.
Conclusion
For any further questions or inquires regarding stair tread installation please contact us or speak with a contractor/installer to determine what method is right for you.
How deep should a stair tread be?
Allowing for a 1 1/2-inch overhang, the minimum depth of the stair tread must be at least 10 inches. Cut the tread to the exact size needed using a miter saw. The blade of the miter saw must cut the wood on ...
Can a miter saw cut through a stair tread?
The blade of the miter saw must cut the wood on the waste side of the marked line or your stair tread will be too short. Do not cut through the line or on the measured side of the tread. Both mistakes will leave you with a wasted stair tread.
How long does it take to install prefinished stair treads?
In other words, half the work is done for you, so installation takes only about 15 minutes per tread.
How deep is stair tread?
Standard tread depth is 11-1/2 inches, and a variety of widths are available to meet your specifications. Additionally, Stair-treads.com is not simply a distributor but also the tread manufacturer, and the company will custom-stain the treads to your flooring.
What are the advantages of prefinished stair treads?
The primary advantage of using the prefinished stair treads is the ease of installation. For example, the stairs shown in this article were built of lumber and covered with carpet. Once the carpet was removed, the raw lumber tread was revealed and it was downright ugly.
What is retrofitting stair treads?
Retro-fitting stair treads is the simplest solution for a DIY’er intent on installing hardwood treads over an existing flight of stairs. High-quality prefinished stair treads are made of solid edge-glued wood—not a veneered or engineered material—and can be used to “cap” or reface an existing tread. The primary advantage of using the prefinished stair treads is the ease of installation.
How do I cut bull nose off of a stair tread?
One way is to cut it off. Using a handheld circular saw or jigsaw, cut the bull nose of the tread back flush with (or slightly behind) the existing riser.
Do you have to remove old lumber treads when refacing stairs?
By refacing the stairs with the new prefinished treads, there was no need remove the old lumber tread. This is a particularly important advantage when dealing with “pre-fab” staircases that are built in a factory and delivered to the jobsite during construction.
Can you cut a riser with a miter saw?
Risers can be cut to length with a miter saw, handheld circular saw, or even a hand saw. I had to rip the risers to width, which is a little trickier. It’s possible to rip the risers with a handheld circ saw with an edge guide, but you’ll get the most accurate results using a table saw with a rip fence.
What to do if there is no space between steps?
If an open space exists underneath the nosing of the tread when it is applied against the step, you must fill the space with Epoxy Nose Caulk. It is essential that there be no space between the step and the stair tread when the installation is completed.
Can you flood stairs?
Do not flood stairs. 4. In stubborn cases, damp mop with room temperature water and solution of liquid detergent suitable for rubber floor covering or a solution of ammonia and water. Immediately rinse stairs with clean room-temperature water, changing rinse water frequently.
Do you cut a tread over size?
Fitting and Cutting. Treads are usually supplied over-size, with untrimmed ends, to allow extra material to compensate for variations in step dimensions. Treads should be individually trimmed to fit each step, both in depth and from side to side. The rear edge should be cut with a slight under-bevel for a better fit.
Can you put rubber treads on steps?
If the shape of the steps do not conform to the shape of the stair treads and cannot be altered to conform, we do not recommend installation of treads unless special instructions are carefully followed. We do not recommend installing rubber treads on exterior steps.
Can you put rubber risers on stair treads?
Rubber or vinyl risers should not be installed so as to extend up underneath the nose of the stair tread. The top of the riser should butt against the bottom of the tread nose.
Do you need to keep traffic off newly installed stair treads?
It is important that traffic be kept off newly installed stair treads, until the adhesive has set up sufficiently to prevent movement and assure a firm bond. Where construction work by other trades requires traffic over newly installed stair treads, protect treads with heavy building paper or planking as needed.
