The basic method is:
- Turn the knob to “Pilot Light”
- Push in the knob and hold it in
- Push the “Pilot Light” button next to the knob
- Release the Knob
How do you light the pilot on a gas water heater?
To light an electric water heater, start by setting the temperature control to the lowest temperature and turning the gas regulator valve to the “Off” position. Then, start the flow of gas by setting the gas valve to the “Pilot” position and pushing down on it. Next, push the red ignitor button near the gas valve to light the pilot burner.
Can you manually light a hot water heater?
Most newer hot water heaters use an electronic igniter, this means that you will not be able to manually light it, the way you could with an older one. This means, if the power is out, you will not be able to light the hot water heater. Do not try to light it manually, to avoid safety issues. When should you hit the reset button on a water heater?
What should I do if my water heater smells like gas?
Contact an appliance repair person, a plumber, or your gas company if you are unable to light the water heater after several attempts. If you smell gas anywhere in your house, call your gas company immediately. Even a “little bit of gas” is too much. Do not turn the gas valve back on until you have replaced the access panels.
Can you manually light a water heater with an electronic igniter?
Can you manually light a water heater with an electronic pilot? Most newer hot water heaters use an electronic igniter, this means that you will not be able to manually light it, the way you could with an older one. This means, if the power is out, you will not be able to light the hot water heater.
Why won't my water heater light?
How to heat water in a gas tank?
What is the difference between a new and old gas water heater?
How to turn on pilot light on gas valve?
What happens if a pilot light doesn't relight?
What happens if you don't see a flame burning in your water heater?
What does it mean when your water heater makes a hissing sound?
See 4 more
About this website
How do you light the pilot on a reliance water heater?
0:481:50Relighting Gas Water Heater Pilot Light - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the dial to the pilot setting. Once in this correct pilot position press and hold the buttonMoreTurn the dial to the pilot setting. Once in this correct pilot position press and hold the button all the way down to the start the flow of the gas to the pilot assembly. Immediately.
Where is the reset button on a Reliance gas water heater?
1:343:24How to Reset a Water Heater Shut-off Button - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst. Okay so with the breaker. Off I'm just going to take off these two screws here take off this.MoreFirst. Okay so with the breaker. Off I'm just going to take off these two screws here take off this. Panel. Okay for this particular brand is a little foam cover that you have to remove. Just.
How do I manually light my hot water heater?
Lighting the Pilot Light on a Manual Hot Water Heater Turn the pilot dial to the off position and wait 5-10 minutes for any gas to dissipate. Then, turn the pilot dial until it says the word pilot. After that, set your temperate knob to low. Now, hold the pilot dial down while you light the burner.
How do I turn up the hot water on my reliance water heater?
0:421:45How to Adjust Water Heater Temperature - YouTubeYouTubeStart of suggested clipEnd of suggested clipFind the knob on the valve. And set the temperature between 115. And 120 degrees this loweredMoreFind the knob on the valve. And set the temperature between 115. And 120 degrees this lowered setting will protect the tank from overheating.
Why is my water heater not igniting?
If the pilot doesn't relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple. The good news: You can usually replace a thermocouple for minimal cost and in less than an hour.
How do you reset the pilot light?
How Can I Restart My Pilot Light?Step 1: Turn off your furnace. ... Step 2: Locate your gas valve. ... Step 3: Hold down the red button. ... Step 4: Light the pilot light. ... Step 5: Let go of the button. ... Step 6: Turn your gas back on. ... Step 7: Turn your furnace back on.
Can you manually light a gas water heater with electronic ignition?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.
Can I relight the pilot light by myself?
Relight the pilot light. Turn the knob to “Pilot,” and let gas to flow to the pilot. Light a lighter or match, then push in the reset button. Hold your flame to the pilot light's opening. Keep the reset switch depressed until the pilot light is burning steadily.
How do you light a gas heater with electronic pilot?
Hold down the reset button and bring a grill lighter or long match to the pilot light valve until the pilot ignites. Once the pilot light stays lit, turn the valve to the “on” position. You should hear the furnace activate.
Is Reliance a good water heater?
Reliance water heaters are some of the most reliable water heaters on the market. Several features make these heaters reliable and have a better value. First, with these water heaters, you'll get more hot water at a time. They come with higher input, gallon size, first-hour output, and recovery.
Where is the thermocouple on a Reliance water heater?
It is usually located beside the unit. At the base of the gas water heater there is a gas valve with the thermostat. Turn the thermostat to its lowest setting and put the gas control knob to the off position. Remove the outer door and two screws that hold the manifold door assembly.
What temperature should my hot water heater be set on?
120 degrees Fahrenheit is the safety recommendation against scalding, but 140° is the common default setting. Most experts agree that anything below 120 degrees creates a risk for bacteria to develop inside your water heater from stagnant water, such as legionella that causes Legionnaire's disease.
How do I reset my gas water heater?
0:202:56How to reset gas water tank pilot light - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou simply hold the button down and spark. It and then here's the most important part you continueMoreYou simply hold the button down and spark. It and then here's the most important part you continue to hold that button down for about 60 seconds.
Where is the thermocouple on a reliance water heater?
It is usually located beside the unit. At the base of the gas water heater there is a gas valve with the thermostat. Turn the thermostat to its lowest setting and put the gas control knob to the off position. Remove the outer door and two screws that hold the manifold door assembly.
Why is my reliance water heater beeping?
A water heater may sound a beep to warn that there is a water leak. Leaks may be obvious if the floor is wet near the water heater, but the leak might also be somewhere along the line. The beeping may be initiated by a water heater shutoff feature, a flood prevention device. Beeping may also signal a gas leak.
Are AO Smith and Reliance water heaters the same?
Reliance Water Heaters is a subsidiary of A.O. Smith Water Products Company, headquarterd in Ashland City, Tennessee. A.O. Smith Corporation had worldwide sales of $3 billion in 2017.
Electronic Ignition Water Heater Won’t Light? (Do This!) - Upgraded Home
Many homeowners have an electronic ignition water heater because of their cheap and easy operation. Sometimes, electronic ignition water heaters won’t light due to improper voltage or loose wires. Whether the unit be underpowered or there is a bad thermocouple, let’s take a look at what you can do when an electronic ignition water heater won’t light.
2. No Warm Water
It’s the big trouble when your device’s fundamental function stops operating, and you end up taking showers with cold water. Nevertheless, there’re three different ways to determine what the problem is.
3. Low Water Pressure
This problem can be caused for both hot and cold water, so you should check the cold and hot water for the concerned tabs and showers.
4. Water Odor
According to the reliance 501 water heater manual, water odor can be caused by the bacteria present in your shower water. Sometimes, it can also be present in your water heater tank. This accumulation can cause the water to become stinking.
How Is The Warranty On Reliance Water Heaters?
In most cases, the warranty applies for both the parts and tanks if failure results from manufacturing defects.
Where Are Reliance Water Heaters Manufactured?
Reliance water heaters are manufactured in Ashland City, Tennessee. As we have seen above, the company is reputable for producing commercial and residential water pump tanks and heaters.
How Long Do Reliance Water Heaters Last?
Just like other water tank options, Reliance tank water heaters last for between 8 to 12 years. The tankless water heaters can last for up to 20 years.
What is a resilient water heater?
As we have above, Resilience water heaters are high-quality products. The tanks are lined with glass which makes the heater durable. It also makes it possible for the tank to retain more heat. The tanks are also built with anode rods to prevent any possible corrosion. It means that the heaters will have a long life compared to other brands.
What is the best water heater for a homestead?
Water heaters are vital additions to a homestead, and buying the best option must be a well-thought-out decision. Resilience water heaters are among the best products on the market that you can select.
What is the energy factor of a heater?
The heater has an energy factor of 3.45
How to reduce the temperature of a water tank?
Locate the temperature dial on the tank and unscrew its cover. Using a screwdriver, adjust the temperature to 120 degrees. For every 10 degrees reduction, you’ll save at least 5% in energy costs.
How Do You Light an Electronic Ignition Water Heater?
The electronic igniter, will either light the pilot light or will light the gas directly. Here are some instructions on how to do so.
Why Is My Hot Water Heater Not Igniting?
If you have been having trouble with your hot water heater not igniting, then there could be several issues. Let’s look at some of the most common problems, so that we may find the solutions.
What happens if you have too much voltage in a water heater?
If you are getting too much voltage, (over 125 VAC) it can cause your igniter to fail. Use your multimeter, to test how much voltage is going to the igniter. Most new electric igniter water heaters will have a control board. The control board will throw a code if there is a problem with the voltage.
What is an induced draft water heater?
Induced draft water heater. An induced draft water heater is a type of water heater that uses a small fan, to draw the combustion gas from the combustion chamber. Induced draft water heaters use an intermittent pilot or hot surface ignition instead of a standing pilot light. Condensing water heater.
Why is it important to have a hot water heater?
We need them to do laundry, take showers, clean dishes, and much more. When you can’t get your water heater to light, you may get a little bit irritated.
How do you know if your gas igniter is working?
Your igniter should light the gas directly if it is a hot surface ignition. You will know it is working if you feel the heat coming from the unit.
How to light a gas igniter?
Lighting a hot surface ignition: Locate the igniter button. Press and hold down the button. Listen for the click and ignition.
Why won't my water heater light?
Low gas pressure or a malfunctioning gas valve may also be to blame if this process doesn’t work. Contact an appliance repair person, a plumber, or your gas company if you are unable to light the water heater after several attempts.
How to heat water in a gas tank?
Reignite the main burner. Turn the main gas valve back “On” and adjust the temperature control to your desired setting. The main burner under the tank should light and begin heating the water in the tank .
What is the difference between a new and old gas water heater?
There are two basic styles of gas hot water heaters, “new” and “old.”. Old style heaters will require you to use your own flame to relight the pilot, while new style tanks come equipped with a pilot light igniter.
How to turn on pilot light on gas valve?
Turn the gas valve to the "Pilot" setting and push down on it. Doing this starts the flow of gas into the tube that supplies the pilot light.
What happens if a pilot light doesn't relight?
If the pilot light doesn’t relight or goes out immediately after relighting, you may have a bad thermocouple. The thermocouple extends from the temperature control into the flame area of the pilot light. They are relatively cheap, and you can install one yourself.
What happens if you don't see a flame burning in your water heater?
If you do not see a small flame burning, then your pilot light has gone out. If you have a newer water heater, it is possible that your panel is not removable and that you view your pilot light through glass. In this case, if you cannot see a flame burning through the glass, then your pilot light is out.
What does it mean when your water heater makes a hissing sound?
Also listen for a hissing sound near the water heater, as this is a sign of a gas leak.
