Place a small bucket under the valve. Turn the nut counterclockwise using a 5/8-inch wrench to remove the hose from the valve. Drain the water from the hose into the bucket. 3. Trace the water line up to the point where the line joins onto the bottom of the faucet. Use a 3/4-inch wrench to loosen the fitting at the end of the faucet.
How do you fix a leaky hose under the sink?
Two fixes to a hose leaking under the sink. Turn off the water supply valve to the leaking flexible hose under the sink. Remove the old flexible braided hose. Check the shut-off valve and sink line. Next, attach your new braided water line. Test it out. Worried about water leaking in other places? Get one of these Why is the sink line leaking?
What to do if the water shutoff valve under a sink?
If the shutoff valve under a sink won't turn, you need to repair it as soon as possible. You don't want to have a water emergency occur and be unable to turn off the water. Knowing various methods to fix a stuck water valve under a sink can protect you from unexpected water troubles.
How do you remove a trap from a kitchen sink?
Locate the large nut connecting the trap to the straight section of pipe that extends down from the sink, called the tailpiece. Turn it counterclockwise to unscrew it. If it's plastic, you can often do this by hand; if it is metal or difficult to turn, use a pipe wrench or adjustable pliers.
How do you remove a flexible braided hose from a faucet?
Remove the old flexible braided hose. Use a wrench to remove the flexible water hose from the water shut-off valve and faucet line. Ours was very tight, so we had to use two wrenches to loosen it a bit. Check the shut-off valve and sink line. Once you have it removed, inspect the water line to make sure nothing was left behind.
How do I disconnect the water line under my sink?
0:321:41How to Disconnect Water Supply Lines in Kitchen Sinks - YouTubeYouTubeStart of suggested clipEnd of suggested clipIs you want to unscrew. The top part that goes up to the kitchen sink. So let's do that real. Quick.MoreIs you want to unscrew. The top part that goes up to the kitchen sink. So let's do that real. Quick. Second thing you know is what you want to do is you want to unhook the hose.
How do you loosen a water supply line?
4:486:56Replace Old Bathroom Water Supply Lines (Without Leaks!) - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine and put it right on top of the nut and then you can turn it counterclockwise to loosen in thatMoreLine and put it right on top of the nut and then you can turn it counterclockwise to loosen in that that's up against the bottom of the faucet.
How do you loosen PVC pipe under sink?
0:072:24Loosening Plastic Plumbing : Plumbing Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you want to grip it just enough that you have a hold on it. Then I take my pair of pliers. And I'MoreSo you want to grip it just enough that you have a hold on it. Then I take my pair of pliers. And I'll grip the other one and just give it a little twist. And they should come right apart.
How do I unscrew my kitchen sink pipes?
1:064:52How to Disconnect a Kitchen Sink Drain - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe union for the trap is still right hand threaded but since it is facing upwards or upside downMoreThe union for the trap is still right hand threaded but since it is facing upwards or upside down loosen it by turning it clockwise.
How do you loosen a tight pipe fitting?
0:001:24Loosen Stuck Pipe Threads - With Heat! - YouTubeYouTubeStart of suggested clipEnd of suggested clipFitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apartMoreFitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.
How do you loosen a stuck compression nut?
1:202:52Compression Ring Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake the rib joint pliers and securely hold the compression nut with them while slowly grinding withMoreTake the rib joint pliers and securely hold the compression nut with them while slowly grinding with the power grinder.
How do you loosen up PVC pipe?
Heat can be used to soften and weaken the PVC. Direct heat onto the joint you are trying to break. Then, as the PVC heats, start pulling the connection apart. If you use heat to separate a pipe from a fitting, both the pipe and fitting should not be reused in pressure applications.
How do you loosen a glued PVC joint?
2:2510:294 GENIUS Ways To Remove Glued PVC Fittings | GOT2LEARNYouTubeStart of suggested clipEnd of suggested clipWhen you found the right one heat it thoroughly for around one minute and put it inside the pipe asMoreWhen you found the right one heat it thoroughly for around one minute and put it inside the pipe as such. What this does is it heats up the glue just enough for the pipe to unstick.
How do you unscrew a pipe without a wrench?
What to Use if You Don't Have a WrenchDuck tape. Duct tape is useful in almost any situation but you may be surprised to learn that you can use it to loosen bolts. ... Two coins. Who would think that money can be used as a makeshift tool? ... Zip-tie. ... Another nut and bolt.
How do you unscrew a pipe?
Squeeze a pair of pliers or adjustable wrenches onto the pipe, placing one on each side of the joint. Keep your tools as close to the joint as possible. Hold one of the wrenches still while you twist the other one to unscrew it. If that fails, you can try turning both wrenches in opposite directions at the same time.
How do you get a stuck thread out of a pipe?
0:181:21How to Remove a Stuck or Broken Threaded Pipe Nipple - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold it in one hand and twist the tool clockwise with the wrench. And it should just loosen. SoMoreHold it in one hand and twist the tool clockwise with the wrench. And it should just loosen. So that's it next time you have a stuck pipe nipple try using an internal pipe wrench tool to remove it.
What happens if you over tighten water supply line?
Do not overtighten the supply line. Screwing a supply line on too tight is one of the worst things you can do. Such overtightening will cause the metal threads inside of the line to become warped, making it much easier for water to slip past. It may also damage the rubber O-rings inside of the line.
How do I fix a clogged water pipe in my house?
1:132:10Cleaning Clogged Water Pipes - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so start with some baking soda to add a little bit of water mix it up. And so it's more likeMoreOkay so start with some baking soda to add a little bit of water mix it up. And so it's more like just a pourable paste type of consistency.
How to prevent a shut off valve from freezing?
Prevent shutoff valves from freezing or becoming stiff by turning the valve on and off twice a year. Place a folded piece of paper towel on the adjustable wrench jaws or wrap it around the shutoff valve prior to moving the bonnet nut to avoid scratching the metal surface. Warnings.
Why does my sink shut off valve freeze?
Sink shutoff valves can freeze or stiffen due to mineral buildup or disuse. The packing nut of the valve, also called the bonnet nut, is unscrewed to loosen the shutoff valve knob and make it easier to turn.
Who is Alexis Rohlin?
Alexis Rohlin is a professional writer for various websites . She has produced works for Red Anvil Publishing and was one of the top 10 finalists in the 2007 Midnight Hour Short Story Contest for OnceWritten.com. Rohlin holds a Bachelor of Fine Arts in English from Madonna University. Related Articles.
How to unstuck a valve?
After a few hours, use a hammer or wrench to gently tap on the valve to help unstuck it. Alternatively you can grab the valve handle with a wrench and use a hammer to gently tap the wrench in a counterclockwise direction.
How to get a stuck shut off valve off?
To loosen a stuck shut off valve, loosen its packing nut then try to turn the handle left and right. If that doesn’t work, spray it with a penetrating oil and wait for a few hours. Blowing hot air over the valve using a hairdryer is also another great way to melt the gunk and loosen it.
Why is my shut off valve stuck?
Stuck shut off valves are caused my corrosions and mineral deposits either on the inside or outside the valve making it hard to turn the valve shaft. Turning all your shut off valves on and off at least twice a year is a good way to prevent them from getting stuck.
What is a penetrating oil?
A penetrating oil is a type of oil with low viscosity (resistance to flow) which allows it to penetrate/seep through a connection thereby lubricating and loosening it . Kroil, PB B’laster, Liquid Wrench and Knock’er Loose Plus are all decent penetrating oils to buy.
How to clean a hair dryer valve?
If using a hairdryer is not viable, boil some water until it starts steaming. Pour it in a bowl (plastic of course) and soak in a heavy cloth/towel. Place the cloth over the valve and wait for a few minutes.
How to get water out of a cloth?
You can as well pour boiling water over the cloth slowly with another container underneath it to collect the water. Check if the valve has loosened.
Can you loosen a shut off valve?
Loosening the packing can loosen the shut off valve as well. Before grabbing a wrench, place a small pan/bucket under the valve to collect any water that may spill once the nut is loosened.
How to remove a swivel nut from a P pipe?
When the nut is disengaged, lower the curved section of pipe and disengage it from the tailpiece. Turn the trap over and empty the water into the bucket. Reverse the procedure to reinstall the trap after you clean it.
What is a S trap in a sink?
If your drain pipes are in the floor instead of the wall , your sink may have an S-trap. It is similar to a P-trap, and the procedure for removing the curved section of pipe is the same.
How to loosen a swivel nut?
Loosen the swivel nut at the opposite end of the "P," either by hand or with a wrench or pliers. When the nut is disengaged, lower the curved section of pipe and disengage it from the tailpiece.
What is a P trap?
Consequently, plumbers call it a P-trap, and it fulfills the important function of sealing sewer gases inside the drain and keeping them out of your house. A pool of standing water inside the curve creates the seal, but hair and other debris that collect there can block it. Removing it for cleaning is a simple task.
What degree does Chris Deziel have?
Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since 1975. As a landscape builder, he helped establish two gardening companies.
Can you reuse a metal trap?
If you have an older metal trap and the nuts are very hard to turn, it may be too corroded to reuse. If so, replace it with a metal or plastic one.
Why is the sink line leaking?
Over time the build-up of minerals in your water like limescale and calcium can begin to wear down the parts of your plumbing. The flexible hose under your sink’s seal can corrode because of the minerals in the water. This is what happened to us. Apparently, they can go every 10 years or so. If your house is getting older, it may be something to pay attention to. This house is now 11 years old, and I’m starting to notice more and more repairs and maintenance that are needed like when our Toilet Tank Was Not Filling Up.
How do I tighten a faucet hose?
Start with the harder-to-reach thread, likely the one that connects to the faucet. Thread it at first with your hands, then use your adjustable wrench to snug it tight. Because of the rubber gasket inside, I was told there was no need for Teflon tape. You should ask when you purchase your flexible hose if it will need plumbers tape or not.
How to remove a flexible water hose?
Use a wrench to remove the flexible water hose from the water shut-off valve and faucet line. Ours was very tight, so we had to use two wrenches to loosen it a bit.
What to do if your water line doesn't work?
If that doesn’t work, you will need to replace the flexible hose under the sink. Make sure that the hose is leaking and not coming from the tap of the sink or elsewhere. Lay some paper towel down on the bottom of the waterline and see where the water is coming through—next, check the water supply line to see if the water is coming out.
How long does it take to fix a leaking hose under the sink?
Many water issues can be tough challenges; however, fixing a leaking flexible hose under a sink is an easy repair. It took all of 5 minutes to do and was very straightforward. If you are new to home repairs, this is one even a novice can tackle.
How to check if a sink leaks?
Turn the water back on at the shut-off valve and inspect for leaks. Turn on the water in the sink to make sure things are running properly. If you tightened everything enough, you’re all done. If you don’t have a water sensor underneath your sink, you may want to check back in a few hours to make sure that there is no leak and that everything has been snagged up properly.
Why does the hose under my sink corrode?
The flexible hose under your sink’s seal can corrode because of the minerals in the water. This is what happened to us. Apparently, they can go every 10 years or so. If your house is getting older, it may be something to pay attention to.
How to get orange rust off bolts?
If the bolt is covered with orange streaks or crumbly bits of rust, scrub them away with a wir e brush and wipe the area dry. Then squirt a penetrating oil like Liquid Wrench on the threads as close to the problem as possible . Give it time to soak in. The longer you let the oil work, the better.
How to remove lime from a nut?
If the nut is encrusted with whitish lime deposits, remove what you can with a wire brush, then brush on white vinegar to dissolve what remains. If a nut resists all these attempts to loosen it, it will have to be cut off with a hacksaw or reciprocating saw.
Why is my faucet nut frozen?
But often that nut will be frozen due to corrosion or mineral buildup from years of water seepage.
How to loosen a nut?
Moving the nut in any direction is progress. Then try to loosen it using a correctly sized wrench. 2. Tap with a hammer. Jarring the nut can break its bond to the bolt. To make sure you hit the nut itself and not the surrounding threads, place a center punch on the nut and strike the punch with a hammer. 3.
Leak prevention tip
Hand-tightened compression nuts for water supply lines always seem to need an extra turn with pliers. But a big part of the problem is low-quality supply lines.
Toilet water supply line installation
Buy a toilet water supply line that has a metal nut or a reinforced plastic nut.
Required Tools for this toilet water supply line Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
Required Materials for this toilet water supply line Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
