There are two ways Deep Fill can be used:
- Add a little more water: Press the Deep Fill button once before starting the cycle to add 3 gallons of water to the wash load. Once the washer has stopped filling, you can press it again to add 3 more gallons.
- Full Tub Fill: Press and hold the Deep Fill button for 3 seconds to fill the washer to the maximum water level. ...
Full Answer
How do you activate deep fill on a GE washer?
0:120:30GE Appliances Top Load Washer - Deep Fill - YouTubeYouTubeStart of suggested clipEnd of suggested clipEnergy and water efficiency. Or with the press of the deep fill button add an extra three gallonsMoreEnergy and water efficiency. Or with the press of the deep fill button add an extra three gallons for even more water hold the button for three seconds for a maximum fill.
How do I get my GE washer to fill with more water?
There are two ways Deep Fill can be used:Add a little more water: Press the Deep Fill button once before starting the cycle to add 3 gallons of water to the wash load. ... Full Tub Fill: Press and hold the Deep Fill button for 3 seconds to fill the washer to the maximum water level.
How do you deep fill a washing machine?
0:000:59LG Agitator Washer - How to Use Deep Fill - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress and hold the deep fill button for 3 seconds before starting the cycle. Note using the deepMorePress and hold the deep fill button for 3 seconds before starting the cycle. Note using the deep fill or max option increases the cycle time because of the added fill time required.
Why won't my GE Deep Fill washer fill with water?
Machine Won't Fill If your washer won't fill, check the hot and cold faucets to make sure they're both turned on fully. GE washers require water pressure between 10 and 120 pounds per square inch. Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks.
What causes a washer not to fill with enough water?
They are: Water Tap Is OFF Or Pressure Is Too Low. Water Inlet Valve Is Clogged. Water Inlet Valve Is Burned Out.
How do I reset my deep fill GE washer?
Motor Reset Procedure:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... The motor has now been reset and is ready for you to start a cycle.
What is precise fill on a GE washing machine?
The Precise Fill feature allows the washer to determine the optimum water required to wash the items in the washer basket. To use this option properly, follow the loading instructions listed in the Owner's Manual for your washer and keep the lid closed during the wash cycle.
How do you bypass the water level sensor on a washing machine?
Quick Water Level Bypassing Formula For Washing MachineLet us say you have 2 lbs of clothes.Add the 2 lbs of clothes in the washtub.Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.Start the wash cycle. ... You have successfully bypassed water level sensor.More items...•
How do I determine the water level in my washing machine?
0:182:15Is the water level in my washer correct? - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart your washer. Small though it should be just about here it shouldn't be that much water now ifMoreStart your washer. Small though it should be just about here it shouldn't be that much water now if you notice that your water level is rising to about here halfway at the tub for higher.
Why does my washer only fills half way?
CLEAN OR REPLACE THE WATER FILTERS (WATER INLET SCREENS) Clogged water filters or inlet screens can cause your washer to not completely fill with water. These small water filters are located in between the water hoses and the water inlet valve on the back of the washer.
Do they make a washing machine that fills with water?
Top-rated smart top-load washer: GE The washer also allows you to customize the water-fill levels at the touch of a button so you can fill the tub with the amount of water you want for your wash, while the smart detergent dispenser stores up to 75 ounces of detergent and indicates when your reservoir is low.
How do you change the inlet valve on a GE washing machine?
0:482:27GE Top Load Washer Inlet Valve Replacement #WH13X10037YouTubeStart of suggested clipEnd of suggested clipPanel. Install the new water inlet valve by inserting the ports through the rear panel reinstall theMorePanel. Install the new water inlet valve by inserting the ports through the rear panel reinstall the mounting screws connect the outlet hose to the new valve and secure the clamp.
How do you bypass the water level sensor on a washing machine?
Quick Water Level Bypassing Formula For Washing MachineLet us say you have 2 lbs of clothes.Add the 2 lbs of clothes in the washtub.Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric.Start the wash cycle. ... You have successfully bypassed water level sensor.More items...•
Why does my washer fill so slowly?
Over time, little bits of sediment build up in the screens in front of your water inlet valves. Eventually, there's so much sediment it restricts the flow of water into your washing machine. Ninety percent of the time, the problem is a dirty water inlet screen. Cleaning the screen fixes the problem.
How much should a washing machine fill with water?
Standard top-load washing machines use between 30 and 35 gallons of water per load.
How do you test a washing machine water level switch?
Testing the SwitchFind the wires leading to the terminals of the switch. ... The water level switch has three terminals. ... Touch the probes to terminals 1 and 3, and note the reading (∞ or approximately 0.0).Touch the probes to terminals 2 and 3, and note the reading.More items...
Why is my GE washer not filling up?
If your GE washer isn’t filling up all the way, the problem is mostly a defective inlet valve. Other reasons also include decreased water flow, a broken wire, or a malfunctioning pressure switch.
Why is my GE washing machine not filling up?
Another reason your GE washing may not be filling up properly is an issue with the faucet. You need to examine your hot and cold faucets to make sure they’re switched. Check that the inlet hoses aren’t kinked while you’re at it.
Why is my water flow so low on my GE washer?
The reason why the water flow to your GE washer may be reduced is if the inlet filter is clogged. The inlet filter is a screen located at the end of the hot and cold water hoses. Its job is to block out any large debris that may be present in the water before it enters the machine.
Why does my washer have a pressure sensor?
It has a pressure sensor that triggers the washer to stop the incoming flow of water once it reaches a particular level. When something damages these sensors, they may incorrectly trigger the hoses and valves to stop water from entering even when the washer didn’t fill up all the way yet.
How to make clothes heavier in washing machine?
Put the clothes into the washer. Choose whatever washing cycle you want to use. Let the washer fill up with water. Once it’s done filling, shut down the washer to drain the water. Now, the clothes will be heavier due to being wet, which will trick the machine into thinking there are more clothes.
Why does my water filter clog?
But over time, these inlet filters can clog due to the build-up of filtered particles, resulting in an inconsistent, decreased water flow.
Does a GE washer fill improperly?
Until you replace or fix the sensors, your GE washer will continue to fill improperly. If you’re looking for a new one, consider getting the New WH12X10412 Pressure Switch for GE Washer. It comes with a 1-year warranty so you won’t have to worry about fixing it or getting a replacement if there’s an issue.
How long does it take for a washer to drain water?
If no other selections are made within 24 hours, the washer will drain the water. To spin the clothes, you must select the "Spin Only" or "Drain and Spin" cycle then press "Start.". You may drain and spin a cycle during any wash cycle.
How to stop a washer from running?
If the washer is running, press "Start" once to interrupt the cycle, select "Drain and Spin" and press "Start" again. If "Stop" has been selected and the washer is still full of water, select "Drain and Spin" and press "Start" again.
