Put the new chainsaw chain
- Start by passing the chain around the motor pulley .
- Then install its guide in the location provided.
- Push the guide all the way toward the pulley to lock it.
- Iron the chain around the guide.
When should you replace the chain on a chainsaw?
When to Replace Your Chainsaw Chain
- If You’ve Reached the “Safety Lines” on the Chain As mentioned above, there are small lines stamped into chainsaw cutter and guides, which indicate how far it can be ...
- If the chain gets broken, dented or chipped If you hit rocks, dirt, ice, etc., your chainsaw chain might have to be replaced. ...
- If your chain is rusty
How to replace the chain on a chainsaw?
Steps On How To Replace A Chainsaw Chain
- Disengage The Chain Brake Of The Chainsaw. In some chainsaws, the chain brake is attached to the side plate. ...
- Detaching The Side Plate Of The Chainsaw. To remove the chainsaw we need to remove the side plate to access the chain. ...
- Release The Chainsaw’s Tension. ...
- Detaching The Chainsaw’s Chain. ...
- Adjust The Tensioning Screw. ...
What are the proper ways to maintain a chainsaw?
To maintain your chainsaw well also look at the following points:
- Adjust the chain tension of your electric chainsaw
- Use the proper lubricant
- Repair the damage caused by randomly Hitting a Nail
- Repair the damage caused by hitting Dirt and Rocks
How to right an inside out chainsaw chain?
How to right a chainsaw chain inside out: Step 1: Ensure you are wearing safety gloves while handling the chain with its sharp cutters. Step 2: Place the chain on a flat surface in the form of a single loop. Step 3: Hold the opposite ends of the loop and twist the chain outward.
How tight must the chainsaw chain be?
The correct chain tension can be checked in two ways: Take the chainsaw chain between your thumb and index finger and lift them 3 to 4 mm, then the...
How to Untangle a Chainsaw Chain?
To untangle a chainsaw chain it is necessary to put the chain of the chainsaw on a horizontal surface and untwist the rings in different directions...
What happens if the chain tension is not correct?
If the chain tension is too tight, the wear on the guide rail and the sprocket increases considerably. Furthermore, the chainsaw loses engine power...
How tight must the chainsaw chain be?
Take the chainsaw chain between your thumb and index finger and lift them 3 to 4 mm, then the tension is fine.
How to tell if chain is on chainsaw?
A chain always lies correctly on the chainsaw when the cutting tooth on the top of the rail points forward. This can easily be checked at a glance.
What happens if the chain tension is not correct?
If the chain tension is too tight, the wear on the guide rail and the sprocket increases considerably.
Why does my chainsaw lengthen?
Over time, it lengthens in size due to the boring of gaps in the connecting links. This process occurs with absolutely any type of chain, therefore, when operating a chainsaw, it is necessary to periodically monitor the correct chain tension and its wear.
What happens if you hang a chain too tight?
A chain that is too loose can cause the guide to derail with rotation. A chain that is too tight can cause accelerated wear of the chain guide, which can even cause smoke if it is not greased. Your chain should hang very partially from the guide, allow 1 cm of maximum deviation .
What causes a chain to expand?
The chain, driven by the motor pulley, will start to heat, which will cause the guide to expand and therefore create additional tension.
Which way to unscrew chain spool?
Now unscrew the cover of the chain spool clockwise.
How Do You Change a Chainsaw Chain?
More often than not, you buy an already-assembled chainsaw where the chain is already attached to the bar.
What to do if chain comes off chainsaw?
If your chain suddenly comes off the chainsaw, the very best thing you can do is to stop using it in the meantime.
Why replace chainsaw chain?
One of the reasons you want to replace a chainsaw chain is poor cutting performance.
How many edges does a chainsaw blade have?
If you look at the top view of the chain, you will notice that the blades have two edges: one sharp and one dull.
What would happen if you checked the direction of the chain from the bottom?
If you check the direction of the chain from the bottom, it would be the complete opposite of the top view.
When the chain is not sagging and stays in contact with the bar after lifting it, you will know that the?
When the chain is not sagging and stays in contact with the bar after lifting it, you will know that the tension is correct.
Should you know your chainsaw before you damage it?
Before you harm yourself or completely damage the chainsaw, you should first get to know your chainsaw and its mechanisms.
How to put chain back on chainsaw?
To reattach your chain, remove the front panel and take the bar and chain off. Line the chain back up on the bar. Hold the chain and bar together and place the chain around the sprocket. Reassemble, then tension your chain.
What happens when you take the front panel off a chainsaw?
When you take the front panel off, since your chain isn’t holding the bar in place, the bar will fall out. I recommend holding onto the bar with one hand while you remove the panel the rest of the way.
Why does my chainsaw chain fall off?
This is the most likely reason why your chain fell off. Running your chainsaw with a chain that’s too loose can cause the chain to pop off when you start cutting.
How to check tension on chain?
There’s two tests to check the tension in your chain; the snap test and the pull test. For the snap test, grab the chain with a well gloved hand and gently pull it away from the bar as far as you can. Allow the chain to snap back, if your chain is tight enough it should snap back into the track.
Why does my chain fall off?
The last reason that your chain may have fallen off is if the sides of your bar track have been worn down and have become too low. As you can imagine, the chain sliding over the bar track creates quite a lot of friction. Over time, this friction where’s down the sides of the bar.
What happens if you can't get your chain to tension?
If you’ve tried to tension your chain but you just can’t seem to get it tight enough, your chain might be the wrong size or it might need replaced.
Why is my chain getting kicked out of the bar?
If these pieces get built up or a larger piece gets stuck, it can cause your chain to get kicked out of the bar track.
Where should the chain be moving on a chainsaw?
If you look at your chainsaw from below, the chain should be moving towards the motor or chainsaw body of the chainsaw.
Which way do chainsaw blades rotate?
All chainsaws have the same chainsaw blade direction. Chainsaw blades ALWAYS rotate clockwise (from left to right).
Why do my chain chains loosen up?
When heavily used, the heat from the motor extends to the bar which causes the chains to loosen up over time.
How to remove bar screws from cardboard?
Place the chainsaw over the cardboard and remove the bar screws and housing.
How far away from the bar should the chain be?
The ideal chain tension is when the drive links ARE STILL engaged once pulled. Check if it can be lifted off up to one-fourth of an inch away from the bar.
Where should the blades of a chain point?
Observe where the sharp edges of the chain point to – the blades should point to the right.
When to do a three way check on chainsaw?
It’s a good practice to always do the three-way check after making any changes or adjustments to the chainsaw. What’s the three-way check, you may ask?
