How do I remove the outdrive from my Mercruiser?
- Disconnect the speedometer hose.
- Lower the drive and place it in forward gear.
- Remove the two plastic caps on the trim-cylinder rod.
- Pound the trim-cylinder rod with a rubber mallet so that it sticks out about 3 inches.
- Place an outdrive cart underneath the skeg to hold the drive level.
How to remove a MerCruiser Alpha One outdrive?
How to Remove a Mercruiser Alpha One Outdrive Step 1. Disconnect the speedometer hose. It is located underneath the exhaust bellows. If the connection is female, push... Step 2. Lower the drive and place it in forward gear. Ensure that the drive is engaged by turning the propeller. Step 3. Remove ...
How do you remove the outdrive on a Ford F-150?
Remove all but one of the six nuts from the bell-housing stud with a socket wrench. Leave the last nut loose; turn it by hand. Remove the last nut and pull the outdrive straight out. The outdrive must be held stable on the cart. Let the trim cylinders slide out and down.
How do you replace an outdrive on a lawn mower?
Place an outdrive cart underneath the skeg to hold the drive level. Secure the outdrive to the cart. Remove all but one of the six nuts from the bell-housing stud with a socket wrench. Leave the last nut loose; turn it by hand. Remove the last nut and pull the outdrive straight out. The outdrive must be held stable on the cart.
How do you remove an outdrive from a golf cart?
Secure the outdrive to the cart. Remove all but one of the six nuts from the bell-housing stud with a socket wrench. Leave the last nut loose; turn it by hand. Remove the last nut and pull the outdrive straight out.
How do you remove the lower unit on a Mercruiser Alpha One?
8:5018:23How do I remove my Alpha 1 gen 2 lower unit - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut it needs to be in the forward position the front tab the shifter needs to be in the forwardMoreBut it needs to be in the forward position the front tab the shifter needs to be in the forward position before you take it off otherwise. It will just hook on. It.
How do I remove my Alpha 1 sterndrive?
0:443:01Removing an Alpha drive. - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe pop the cap off the pinpoint anchor pop that out so and then we have six nuts that we remove oneMoreWe pop the cap off the pinpoint anchor pop that out so and then we have six nuts that we remove one two three and three on the other side so we'll go ahead and move those this is a 5/8.
How do I change my sterndrive on my boat?
0:144:04How To: Remove ,Replace & Change Mercruiser Marine Bravo Stern ...YouTubeStart of suggested clipEnd of suggested clipWhen it comes off there's a shift cable right in here and it generally pops off but sometimes whenMoreWhen it comes off there's a shift cable right in here and it generally pops off but sometimes when they're a little older. And use the little clip can stick.
How do I uninstall outdrive Alpha 1 Gen 2?
3:1210:52Mercruiser Alpha One gen-2 stern drive removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipObviously this little rubber thing isn't threaded. So you can just pull it out once you get that oneMoreObviously this little rubber thing isn't threaded. So you can just pull it out once you get that one nut off on one side.
How do you remove a stuck sterndrive?
2:347:13How to Remove a STUCK Sterndrive CORRECTLY! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the next thing you want to do is in my case at least I lower the bow of the boat down at theMoreSo the next thing you want to do is in my case at least I lower the bow of the boat down at the front on the tongue just crank down the tongue.
How do you remove a Mercruiser Bravo 3 outdrive?
0:056:34R&R Bravo III Out Drive Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a thick steel you can use a block of wood as well. We do need some wrenches socketsMoreIt's a thick steel you can use a block of wood as well. We do need some wrenches sockets screwdrivers and if you have some seal tools this is really good to take the seals off the share.
How often should Mercruiser bellows be replaced?
every two yearsInspect the bellows annually and replace it every two years.
How do I identify my Mercruiser outdrive?
0:223:45Mercruiser Outdrive Identification -- Alpha Gen 1, Gen 2, and BravoYouTubeStart of suggested clipEnd of suggested clipThe higher power rated um versions. So um those bravo drives um what we're looking at here is anMoreThe higher power rated um versions. So um those bravo drives um what we're looking at here is an alpha gen alpha one gen two so alpha would be the name of the drive.
How do I remove Mercruiser bell housing?
4:259:03How to remove the Gimbal housing on a Mercruiser Bravo I ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd all those are or just some pins with cotter pin there's strike pins that go through with littleMoreAnd all those are or just some pins with cotter pin there's strike pins that go through with little cotter pins on the bottom. You. Pull those off.
How do you remove the lower unit on a Mercury inboard motor?
0:5812:13Remove Stuck Lower Unit | Mercruiser, Alpha 1 - Gen 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis lower unit to the upper unit with a 5 16 allen you can remove that boat. And then down. Here.MoreThis lower unit to the upper unit with a 5 16 allen you can remove that boat. And then down. Here. You can see these two there's two nuts here those are five ace nuts. And then on the front.
How can you tell the difference between Gen 1 and Gen 2 Alpha?
The Alpha Gen II upper and lower housings are fastened together with two through bolts on either side of the drive along with the front and rear bolts, while the Gen 1 drives use one stud visible on either side. Alpha Ones have two studs under the ventilation plate just above the prop.
Do you have to remove outdrive to remove engine?
If it's I/O you need to pull the out drive because the outdrive shaft goes into the engine coupler.