how do i reset my coleman furnace

1. Turn the Coleman furnace system switch to the "Off" position on the electric service panel.
2. Locate the manual reset switch near the left side of your furnace blower. ...
3. Press the reset button, which you will find in the middle of the limit switch. Use this manual reset button when the furnace burner will not operate.
4. Turn the system switch to the "On" position.

Where is the reset switch on a Coleman furnace?

Turn the Coleman furnace system switch to the "Off" position on the electric service panel. Locate the manual reset switch near the left side of your furnace blower. Your Coleman furnace has an upper limit switch for manual reset and a lower limit switch for automatic reset.

How do you turn off the upper limit on a Coleman furnace?

Identify the circuit breaker switch that controls the electricity to your Coleman furnace. Move the switch into the "Off" position. Examine the furnace to locate the upper limit switch.

How do I Stop my Coleman furnace from overheating?

Your Coleman furnace also has two high temperature limit switches to protect it from overheating by turning off the power to the ignition controlling the gas valve. You must reset the Coleman furnace switch to get your furnace operating again.

How do you reset a Coleman upper limit switch?

Performing a manual reset on a Coleman upper limit switch is a quick and simple process. Open the cover of your circuit breaker box. Identify the circuit breaker switch that controls the electricity to your Coleman furnace.

Does a Coleman furnace have a reset button?

The reset button on a Coleman furnace is located in the middle of the control panel. Their specific location is in the middle of the upper and lower limit switches. The upper limit switch will allow you to do a manual reset and the lower limit switch allows for an automatic reset.

Where is the reset button on my furnace?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

Why is my Coleman furnace not working?

Most likely, either the electrical system providing your furnace's power has shorted or the power switch has blown. Try resetting your furnace's circuit breaker. If it has blown, you will need to replace it. The furnace's igniter might either be cracked or faulty.

How do I reset my Coleman HVAC?

How do you reset your AC unit?Turn off your air conditioning system using the thermostat. ... Search for the breaker box. ... Shut off your AC unit at the breaker. ... Wait at least a full minute before switching the breaker back to the “on” position.Wait for 30 minutes before turning your unit back on at the thermostat.More items...•

What causes a furnace to need to be reset?

The basic purpose of a reset button is to serve as a safety feature. It helps shut down the furnace when the furnace is too hot. This essentially prevents the overheated furnace from triggering the circuit breaker. As noted above, a furnace may need to be reset sometimes, such as when it is too hot.

How long does it take for a furnace to reset?

Press and hold the reset button for about 30 seconds. Raise your thermostat to the desired temperature. This should ignite your furnace. If there's no ignition, then it's time to call a professional.

What does 3 flashes mean on a Coleman furnace?

CODE: Three red flashes. RESULT: Pressure switch is stuck in the open position. FIX: Check if there is a faulty inducer, a blocked vent pipe, a broken pressure switch hose, or a faulty pressure switch.

Where is the limit switch located on a Coleman furnace?

1:123:34Furnace - Limit Switch | Repair and Replace - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst disconnect the wires. Now unscrew and remove the limit switch. Take the multimeter and set itMoreFirst disconnect the wires. Now unscrew and remove the limit switch. Take the multimeter and set it to the lowest ohms of resistance.

How do you ignite a Coleman furnace?

2:546:03How to light a pilot on a mobile home furnace - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you'll do you'll get your match inside of there right where it needs to go you will pushMoreSo what you'll do you'll get your match inside of there right where it needs to go you will push this down at that point and it'll light in there.

What is a limit switch on a Coleman furnace?

Coleman furnaces contain two internal safety components—known as high-limit switches—that are designed to stop electricity from reaching the gas ignition valve if the furnace overheats to dangerous temperatures.

Why is my furnace blower not working?

If you see or hear the fan turn on, your blower motor is not the culprit. If the fan does not start, you have a wiring issue (circuit breaker trips) or motor problem (circuit breaker does not trip). While your thermostat may be at fault, only an HVAC technician can diagnose and remedy the issue correctly.

Where is the pilot light on my Coleman furnace?

0:473:05Tips to lighting the pilot on a Coleman furnace in a manufactured home.YouTubeStart of suggested clipEnd of suggested clipThe front okay the front of this little you it's very difficult to see here there's just not enoughMoreThe front okay the front of this little you it's very difficult to see here there's just not enough light. But you need there's like a little rectangular.

How do I turn my furnace back on?

2:134:41Relight a Natural Gas Furnace - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you have matches or a barbecue lighter on hand turn the power switch off it is typicallyMoreMake sure you have matches or a barbecue lighter on hand turn the power switch off it is typically located near the furnace wall or ceiling carefully remove the furnace door as the inner door may be

What do you do when your furnace doesn't turn on?

What to Do When Your Furnace Won't Turn OnCheck Your Circuit Breakers. Even if you use a gas or propane furnace, some of the components run on electricity. ... Check Your Thermostat. ... Check the Drain Pan. ... Check Your Air Filter. ... Check the Pilot Light. ... Check Your Natural Gas or Oil Supply.

How do I reset my furnace lockout?

Regardless of the culprit, you will have to perform a reset procedure to get your furnace out of lockout. Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again.

Why is my heat not turning on?

If your heating system will not turn on, the first thing you should do is check the thermostat. The thermostat's battery may have gone bad, causing it to power off. If your thermostat is hardwired, a power surge, brownout, or brief power outage may have caused the thermostat to lose its settings.

How long do you have to wait to reset a furnace?

Some furnaces have a minimum time threshold for resetting the electrical settings, and waiting at least 5 minutes ensures that this threshold is met.

How to turn on a furnace when restarting?

Set your thermostat to kick the heater on when it restarts. On your thermostat or control unit, turn the heat up so that the furnace will kick on when you restart it. In other words, if it is 70 °F (21 °C), set your thermostat to at least 75 °F (24 °C). If it is 80 °F (27 °C), set your thermostat to 85 °F (29 °C). This way you won’t have to worry about the temperature sensors on your thermostat interfering with your reboot.

What to do if your furnace doesn't work?

If your furnace doesn’t do anything, check the thermostat again to make sure that your furnace is getting accurate information from the control.

What does a green light on a furnace mean?

On older furnaces, a steady green light is usually the diagnostic sign for all-clear. Newer control units will either read “ready,” “on,” or “clear.”. On every furnace with a diagnostic unit, there is a piece of paper taped to the inside of your removable panel.

How to tell which furnace panel is removable?

To determine which panel is removable, look in the corners of each panel. One of the will be screwed or soldered into the body of the furnace . The other one can be removed.

How to tell which side of a furnace is removable?

To determine which panel is removable, look in the corners of each panel. One of the will be screwed or soldered into the body of the furnace. The other one can be removed. Tip: To figure out which side of your furnace is the front, look for the brand name or company logo of the furnace’s manufacturer.

How to check oil tank on furnace?

If you have an oil furnace, look at the top of your tank for a small glass or metal gauge with numbers on it . It is usually affixed to one of the pipe connections on top. This is the oil gauge. If the needle or line on the gauge is in the red, you need to refill the oil on your tank.

What to do if you smell gas coming from a Coleman furnace?

If you smell gas coming from your Coleman furnace, leave immediately and call for help. Founded in 1900, Coleman Heating and Air Conditioning has been manufacturing HVAC equipment for residential customers for over 100 years. Coleman furnaces contain two internal safety components—known as high-limit switches—that are designed to stop electricity ...

What is a high limit switch on a Coleman furnace?

Coleman furnaces contain two internal safety components—known as high-limit switches—that are designed to stop electricity from reaching the gas ignition valve if the furnace overheats to dangerous temperatures. The furnace's lower limit switch is programmed for automatic reset, but the upper limit switch must be manually reset.

How to find upper limit switch on furnace?

Examine the furnace to locate the upper limit switch. Look for a small round component with a raised red button at its center.

Where is the reset button on a furnace?

The location of the furnace reset button depends on the brand and model of your exact furnace. If you have central AC system in your house, the reset button should be find on the blower motor. Read on to know how to find the furnace reset button location, click here.

What to do if furnace doesn't start?

If the furnace doesn’t restart, call HVAC technician to troubleshoot the furnace and determine the exact problems. Only a professional can properly identify why your furnace isn’t starting.

Most Common Problems

Armed with the DIY spirit, you can be the 'furnace guy.' Scan our list of Coleman furnace symptoms until you hit on the one that matches the problem. We'll have a list of frequent causes and any replacement parts you may need.

The Right Parts for the Job

We carry more than 4 million parts from over 175 major brands, so chances are, we've got the part you need.