-1.png?width=688&name=Screenshot (77)-1.png)
Reset the Motion Sensor
- Press the bottom of the face and push up to remove the sensor from the battery cover.
- Remove both batteries from the motion detector.
- While holding down the tamper switch (C), insert one battery into the motion detector.
- Release the tamper switch after one to two seconds.
- Insert the second battery into the motion detector.
- Replace the sensor on the battery cover.
- Press the bottom of the face and push up to remove the sensor from the battery cover.
- Remove both batteries from the motion detector.
- While holding down the tamper switch (C), insert one battery into the motion detector.
- Release the tamper switch after one to two seconds.
How do I know if my Xfinity home motion sensor is working?
Check the Xfinity Home app to see if the sensor status changes when you walk by it. Or, set up a temporary rule for the system to text you whenever the sensor detects movement. When the sensor is triggered (detects movement), it notifies your system and then goes to "sleep" for two minutes to conserve battery power.
How do I restart the motion sensor?
Restart the Motion Sensor by removing its battery, waiting a few seconds, then reinsert the battery. If the message remains, replace the battery with a fresh battery. If the problem is not resolved, it may be caused by an issue with your touchscreen's location.
How do I reset the sensor to factory default settings?
Insert the battery. The sensor should illuminate the LED once when boot-up/initialization tasks are complete. Release the tamper switch while the LED is illuminated (it will be lit for 4 seconds). The sensor should then reset to factory default settings and begin searching for any available home controller or security system.
What should I do if my motion sensor battery is low?
Replace the Motion Sensor battery within two weeks of receiving a low-battery alert. Verify that the Motion Sensor's battery compartment is fully and securely closed. If the issue persists, remove and replace the Motion Sensor battery. If the problem persists, contact us.
How to remove battery from motion detector?
How long does it take to release a tamper switch?
About this website
How do I reset my Comcast door sensor?
The Touchscreen Displays a Communication Lost With Your Door/Window Sensor Message. Restart the Door/Window Sensor by removing its battery, waiting a few seconds, then reinsert the battery. If the message remains, replace the battery with a fresh battery.
How do I fix my Comcast motion sensor?
The Motion Sensor with which you're having trouble....The Touchscreen Displays a Communication Lost with your Motion Sensor MessageRestart the Motion Sensor by removing its battery, waiting a few seconds, then reinsert the battery.If the message remains, replace the battery with a fresh battery.More items...
How do I test my Comcast motion sensor?
Motion Sensors Make sure your system is disarmed. Use the touchscreen to bypass the Motion Sensor. Make sure there is no movement in the area for two minutes. Walk in front of the Sensor, then check your system activity in the Xfinity Home app to see if the motion event was detected.
How do you reset a door sensor?
instructions:Take off the Sensor's cover and remove battery. ... Touch the Sensor's body with a magnet.Insert the battery.Within 2 seconds remove the magnet from the Sensor's body, the LED will turn off. ... Remove the battery.Re-install the battery.Reset will be confirmed by LED blinking.
What does the Xfinity Motion Sensor do?
An Xfinity Home motion sensor detects unexpected motion in large sections of your home while you're away. Set rules to get real-time alerts or trigger other connected devices, like lighting when activity is detected.
How do you change a Motion Sensor battery?
0:411:52How to Replace the Battery for a Home Security Motion DetectorYouTubeStart of suggested clipEnd of suggested clipNext you must release the lens from the device by depressing three tabs on the device. Two on topMoreNext you must release the lens from the device by depressing three tabs on the device. Two on top and one on the bottom. Next remove the batteries insert the new batteries. Pay attention to polarity.
How do you test a motion sensor?
Walk-in front of your motion sensor, your panel's home button will flash Yellow. This will occur each time a motion signal is transmitted. This will allow you to determine if the sensor is detecting movement and also let you explore its range capabilities.
Does Xfinity Home have a panic button?
Press the red Emergency button at the bottom of the touchscreen. On the Emergency screen, tap the panic button for the type of help you need, and hold it for two seconds. Your alarm will sound, and an alert will be sent to the Central Monitoring Station.
What does comm failure mean on Xfinity alarm?
When your touchscreen displays a comm failure alert for a Door/Window or Motion Sensor even after you replaced the batteries, it may indicate that the sensor has stopped working properly and needs to be serviced.
How do I connect my Comcast home door sensor?
Put the sensor in pairing mode by placing the sensor face down and removing the plastic battery tab. The green LED blinks three times every five seconds to indicate that the sensor is searching for the touchscreen. This can take up to five minutes.
Why are my door Sensors not working?
If your door sensor is wireless, a dead battery may be the reason your door sensor is no longer working. Many panels will notify you if the battery in your wireless door sensor is running low so that you can replace it before it fails.
Where is the reset button on Ring door sensor?
Press and hold the setup button (located inside the device) with the battery in, until the LED stops flashing (approximately 10 seconds). Press and hold the Connect Button (located on the side of the device) for 10 seconds until the LED Ring blinks once, then release the button.
How do I change the battery in my Xfinity Motion Sensor?
0:181:39XFINITY Home Battery Replacement: Tyco XHS1-TY motion sensorYouTubeStart of suggested clipEnd of suggested clipThe old batteries by gently lifting them out of the battery. Compartment. Next insert two newMoreThe old batteries by gently lifting them out of the battery. Compartment. Next insert two new batteries into the battery slots positioning the batteries as shown in the diagram.
What does comm failure mean on Xfinity alarm?
When your touchscreen displays a comm failure alert for a Door/Window or Motion Sensor even after you replaced the batteries, it may indicate that the sensor has stopped working properly and needs to be serviced.
Why is my Xfinity keypad flashing?
The status light turns red and flashes when the system is armed. For an SMC Wireless Keypad: Enter a valid keypad code. Press the button for the Armed mode (Arm Away or Arm Stay) that you want to activate.
Why is my Xfinity Home security beeping?
The device makes beeping noises when arming and will beep faster as your security system gets closer to its armed state. Beeping will stop when the system is armed.
Xfinity Home: How do I clear a low battery and tamper alert on ... - reddit
Seems to be no info on this online. Should it be automatic? I followed the instructions that Xfinity posted to replace the battery, but the tamper alert and low battery alert are not clearing after putting things back together.. EDIT: I have also rebooted the touch screen and the modem, walked past the sensor a few times, and armed/disarmed the whole system (had to bypass the sensor of course).
Motion Sensor Troubleshooting - Xfinity Support
Learn what to do when you have a problem with a Motion Sensor connected to your Xfinity Home system.
Motion Sensor Troubleshooting – Xfinity
Learn what to do when you have a problem with a Motion Sensor connected to your Xfinity Home system. What You'll Need: Xfinity Home; The Motion Sensor with which you're having trouble
Xfinity home "sensor tampered" message after battery change
Hello and Happy Monday, Shankarhokie!I hope you’re having a great week so far! I also appreciate you taking a moment out of your day to reach out to us on our Community Forums!
How to remove battery from motion detector?
Press the bottom of the face and push up to remove the sensor from the battery cover. Remove both batteries from the motion detector. While holding down the tamper switch (C), insert one battery into the motion detector. Release the tamper switch after one to two seconds. Insert the second battery into the motion detector.
How long does it take to release a tamper switch?
Release the tamper switch after one to two seconds.
Why doesn't Comcast offer symmetrical 1 Gbps service over DOCSIS 3.1?
Can someone explain to me why nearly 10 years after DOCSIS 3.1 was finalized with support for 1-2 Gbps upstream data the maximum upload speeds Comcast will support (without paying $300/month for their fiber service) is 35 Mbps?
Xfinity locked comments last time, existing issue about continued "accidental" throttling in Monterey, CA still here despite being completely unhelpful before (surprisingly)
Even though you locked the comments on my last post about continually throttling my internet by "accident", I'm still having major issues with my service. Turns out locking and hiding that post didn't help anyone, and is just adding to the paper trail of consumers demonstrating that they tried to get an amicable solution to a problem first.
Failed Refund, wants me to pay for it?
Had a wonderful experience with live chat where this poor ladies supervisor messed up a refund on my account causing me to owe $170. Then I'm asked to pay it again. This seems illegal? Great service.
On going outage
My internet has been out for the last 4 hours. The estimated time given in the app has lapsed. I’d love any info or help to resolve this.
I am having trouble getting a technician out to our house to move the cable line
On our property we have two power poles and on 01/03 during some heavy snow fall the power poll behind the house fell over and is currently resting on top of our house.
How to remove battery from motion detector?
Press the bottom of the face and push up to remove the sensor from the battery cover. Remove both batteries from the motion detector. While holding down the tamper switch (C), insert one battery into the motion detector. Release the tamper switch after one to two seconds. Insert the second battery into the motion detector.
How long does it take to release a tamper switch?
Release the tamper switch after one to two seconds.
-1.png?width=1720&name=Screenshot (77)-1.png)