- Remove the top cover of your ezH2O unit.
- Press the black reset button located in the top right side, holding for about two seconds before releasing.
- Different messages will flash across the LED interface. ...
- At this point, the filter status light should change back to green when correctly reset.
- Replace the top cover and your filter status reset is complete.
Full Answer
How do I Reset my Elkay EZH2O filter status?
How do I reset my Elkay ezH2O bottle filler filter status? *The directions below are for units with an LED bottle filler counter. Remove the top cover of your ezH2O unit. Press the black reset button located in the top right side, holding for about two seconds before releasing.
How do I reset the filter on my Elkay bottle filling station?
Older Models: Older Elkay ezH2O bottle fillers will not automatically reset with a new filter installation. Here are step-by-step directions for resetting the filter state on older Elkay bottle filling stations, directly from Elkay. Remove the top cover by unscrewing the two Torx screws located on top of the unit.
How do I Reset my EZH2O bottle filler counter?
*The directions below are for units with an LED bottle filler counter. Remove the top cover of your ezH2O unit. Press the black reset button located in the top right side, holding for about two seconds before releasing. Different messages will flash across the LED interface.
How do I Clean my Elkay EZH2O cooler?
Elkay recommends using a soft cloth (we think microfiber would work well) along with mild dishwashing soap to spray and wipe down the unit. We recommend paying extra attention to the bubbler, push buttons, and other areas of the cooler that are often touched by users. How do I change the filter on my Elkay ezH2O cooler?
What does the green light on an Elkay EzH20 mean?
How to change a filter in a bottle?
How to check if filter is properly installed?
Does Elkay EzH2O reset filter?
Can you add videos to your watch history?
How to clean Elkay cooler?
Elkay recommends using a soft cloth (we think microfiber would work well) along with mild dishwashing soap to spray and wipe down the unit . We recommend paying extra attention to the bubbler, push buttons, and other areas of the cooler that are often touched by users.
What time does Elkay water cooler work?
Phone hours are Monday through Friday, 7:30 AM - 5:00 PM EST. Hopefully, this article helps you identify the cause of issue for your water cooler, along with how to fix it and get your Elkay unit back in proper working order.
What causes back pressure in bubbler stream?
Bubbler stream waterway is partially restricted causing back pressure or less space to flow through the bubbler causing back pressure. Clean or replace bubbler.
How to clean a strainer valve?
To clean the strainer, unscrew the solenoid valve cap. Remove the screen and rinse thoroughly with water. Insert screen back onto solenoid valve and make sure o-ring is placed properly.
What happens if you add a water filter to a stream?
If a new water filter is added and the stream becomes low, that filter may cause the water flow to lessen. If this occurs, then you will need to replace the filter.
Why does water run even after power cord is unplugged?
Water continues to run even after the power cord is unplugged. This means that the solenoid or solenoid diaphragm is defective. Replace the solenoid. You will know the solenoid is the issue is you unplug the power cord and the water flow does not immediately stop.
Why is my water stream low?
The solenoid may also be the cause of low water stream. This occurs when the solenoid will not open up all the way. The models this is applicable to are EZ, HTV, and electronic eye models. If this is the case, the solenoid needs to be replaced.
What happens if the program button is not pushed again?
If the program button is not pushed again the display will scroll through the two messages above for three cycles and then default back to bottle count and be back in run mode.
How many pages are in the installation manual for EZWSRK?
Here is the full 19-page Installation and Use Manual for EZWSRK and LZWSRK ezH2O Bottle Filling Stations. These control board instructions as well as additional instructions concerning the control board can be found on page 17 including:
How long does it take to see the bottle counter on a Refrig?
REFRIG units: Place bottle or hand in front of sensor for approximately 9 seconds to see bottle counter count 00000001, (This is based on filling a 20 oz. bottle).
Who is the distributor of Elkay fountains?
Equiparts has been a master distributor of Elkay units and repair parts for over 25 years. Work with us to get expert support for your Elkay drinking fountain and bottle filler needs.
Who sells Elkay filters?
Equiparts is a master distributor of Elkay. We sell all of the units, repair parts, and filters Elkay makes, with many of them in stock and ready to ship. Listed below are related parts and filters for EZWSR and LZWSR units:
Can you find repair parts for Elkay?
If you cannot find the repair parts or units you need, give us a call to place your order. Elkay makes many variations of their bottle fillers and we do not have every configuration listed online. Know that when you call in for help with Elkay units or parts, we will connect you with an Elkay repair parts specialist. We have worked with Elkay for many years, and know their units very well.
How do I make my Elkay water fountain colder?
To adjust the cold feature, unscrew the top part of the water fountain and adjust the toggle switch to the colder setting. The LED display will display the cold setting enabling you to adjust as needed. Refer to your manual for more directions.
How to relieve pressure on water fountain?
Unplug the the water fountain or Turn off the water supply; then dispense water to relieve pressure (through either the bubbler or the bottle filler).
Why is my water fountain flashing red?
Flashing Red: (only applies to P-SKU’s) Filter is installed backward or an issue with the NFC board in the water fountain or tag on the filter. Remove the filter and reinstall 1800 from the original position. See also the troubleshooting guide.
Why isn't my fountain draining?
If the fountain does not drain after this , the push button may be defective and needs to be replaced. Alternatively, the drain hole opening mechanism may be damaged and need to be replaced or fixed.
How to remove top cover of bottle filling station?
Remove the top cover of the bottle filling station by unscrewing the two Torx screws.
Why is my fountain not getting cold?
If the water in the fountain is not getting cold, there is an issue with the compressor. Here are some common compressor issues and how to fix them;
What to do if water fountain is not cold?
If the water fountain’s water is not very cold, check to see if the compressor is low on refrigerant and refill the refrigerant or contact a service agent to do it. Additionally, clean the condenser fins in front of the fan, causing the compressor to malfunction.
What is a ezh2o liv pro?
Serve guests and colleagues cleaner, healthier water in a sustainable way with an ezH2O Liv Pro. This eco-friendly filtered water dispenser is engineered to accommodate the extra capacity needed in commercial spaces such as lobbies and conference rooms.
What is an Elkay ezh2o?
Elkay’s ezH2O Liv is the first built-in filtered water dispenser designed for the home! It's a convenient addition to any room, from your entertaining space to the master suite, and even the kitchen.
How long is the Elkay warranty?
There is a one-year residential or commercial warranty, depending on the unit purchased. Please see the Elkay Limited Product Warranty and Software License for more information.
How to remove filter box cover?
Begin by putting on cut-resistant gloves and safety glasses. Remove the four screws from the filter box cover using an Allen wrench.
How many gallons of water does a commercial water filter have?
Residential models have a 750-gallon filter. Commercial models have a 3,000-gallon filter.
How to activate water dispenser?
Activate the water dispenser by placing the bucket in the alcove to relieve pressure in the water line. Shut off the power to the unit at the circuit breaker. Lift the water line. As you remove the filter, place a towel within the cavity to absorb the water.
Where to install filtered water dispenser?
Install a stylish, eco-friendly filtered water dispenser in convenient areas of your home or business. Place anywhere near a water line and electrical. In homes, install in mudrooms, recreation rooms, playrooms and even in a second-floor hallway.
What does the green light on an Elkay EzH20 mean?
The green light indicates that the filter has between 100-21% of its filter life left. No action is needed when an Elkay bottle filler filter light is green.
How to change a filter in a bottle?
Remove the red cap from the new filter, and insert the filter into the bottle filler. Turn the filter clockwise until you cannot turn it any further.
How to check if filter is properly installed?
Checking that the filter is properly installed - Is the label facing forward, white tag facing back, filter in the right orientation, etc.
Does Elkay EzH2O reset filter?
Older Models: Older Elkay ezH2O bottle fillers will not automatically reset with a new filter installation. Here are step-by-step directions for resetting the filter state on older Elkay bottle filling stations, directly from Elkay.
Can you add videos to your watch history?
Videos you watch may be added to the TV's watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.