how do i stop my dvr from beeping

Here are the steps to disable the beeping on the NVR/DVR: Using the mouse, right-click on the screen; Click on " Menu ";

Full Answer

Why is my Hikvision NVR/DVR beeping?

Another aspect you need to consider regarding “beeping sounds” is the exception feature of Hikvision devices. There exists a list of exceptions that can generate a certain alarm. Below we will list all the beeping sound problems and solutions for Hikvision recorders. First of all, make sure you’re using a surveillance hard drive in your NVR/DVR.

How do I Stop my recorder from beeping?

How can I stop my recorder from beeping II: Check The log. In order to get to the log, first, you’ll need to log into the recorder using your pattern or password. Right-clicking the screen and clicking the ‘main menu’ will usually prompt the login page.

How do I get my Hikvision to stop beeping?

The interface on the (new) Hikvision recorders may vary, but the procedure is the same, there’s always a “init” option. Now, your hard drive is ready to be recorded onto and the annoying beeping alarm will stop.

Why is my recorder beeping after hard drive initialization?

If your recorder is beeping after the hard drive has been initialized then this may be caused by things such as not having a network cable connected or certain cameras being offline. Here are the steps how to turn off these alarms. The first step is to right-click on your mouse and log in to your recorder, and then select ‘Menu’.

How do I turn off the beeping on my DVR?

0:474:17How To: Turn off the alarm beeping sound from the DVR - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf using the remote press the button that says alarm. If you are not logged in it will ask you for aMoreIf using the remote press the button that says alarm. If you are not logged in it will ask you for a password. Type. In your password. And press ok if you do not have a password then leave it blank.

Why is my DVR keep beeping?

This message means that your recorder has lost an ongoing connection to a particular IP camera. In this case, check the camera itself to make sure it's still functioning by doing a power/IR test. Check its network cable as well, and source of POE power. If the camera is no longer working, replace the camera.

Why is my HIK DVR beeping?

The most common reason people get this beeping sound is because they are powering up their Hikvision DVR/NVR for the first time with a hard drive that has not been 'initialized' (or it's not even installed).

Why is my H 264 DVR beeping?

If you find your DVR beeping or buzzing, it is because there is a setting in the DVR that activates the internal buzzer to sound when a hard drive error is detected. This is set by default on DVRs and NVRs we sell. The video below will guide you how to disable the internal buzzer on the DVR.

How do I stop my Lorex DVR from beeping?

To disable warnings:Right-click on the Live View to access the Quick Menu.Click Main Menu and then click the Setting icon ( ).Click Event > Warning.Click the Network tab.In the Event Type drop-down, select from the available alerts.Uncheck the box next to Buzzer and click Apply.

How do I stop my Dahua DVR from beeping?

0:001:04How to Turn Off Beeping Noise On Dahua DVR/NVR - YouTubeYouTubeStart of suggested clipEnd of suggested clipI. Come down to abnormalities. I see here that the event is no hard drive and what I'll do is I'llMoreI. Come down to abnormalities. I see here that the event is no hard drive and what I'll do is I'll say enable. And save of that I know is coming out an event type. So.

How do I turn off HIK connect notifications?

Enabling/Disabling Alarm NotificationEnter the Settings page.Tap Alarm Notification to enter the Alarm Notification page.Tap the icon / to enable/disable Alarm Notification.(Optional) Set the notification schedule.(Optional) On the Alarm Notification page, tap Notification Sound Mode to set the sound mode.

Why is my Dahua NVR beeping?

Generally speaking, the beeping indicates there's an error issue with the system, a warning message by the recorder. It can be a motion detecting beeping or an indicator that your hard drive is damaged and the machine is not recording at all. Either way you need to investigate the issue.

How do I know if my DVR hard drive is bad?

Indicators the Hard Drive on your DVR may have failed If you try to access recorded video surveillance footage and you cannot find any video in the history or playback section of your DVR.

How do I stop ZOSI beeping?

Zosi NVR is beepingRight click your mouse (the one connected to your NVR), then go to System Setting > General Setting > Error Setting. Here make sure that “Enable” and “Buzzer” are unchecked (unticked).Right click your NVR mouse again, then go to System setting > Channel Setting > Video Detection.

How can I fix my DVR problem?

DVR TroubleshootingMake sure your equipment (TV and cable) is properly connected and powered on.Make sure the coax cable is connected to the outlet.Remove any objects around your receiver to allow proper ventilation.Refresh your receiver.Unplug your receiver and wait at least 60 seconds before plugging it back in.

Why does HIK connect keep beeping?

The most common reason people get this alarm sound is because they are setting up their recorder for the first time with a hard drive that has not been 'initialised'. This is just another word for formatting, which is the process of wiping off the hard drive and preparing it to be used by a new device.

Why is my HIK connect not recording?

This message (“no record file”) shows up on an NVR, DVR, or on a single camera that has a microSD card. The issue is related to incorrect recording settings, corrupt hard drive (or microSD card), and, in some cases, glitches on the firmware.

How do I turn off Hikvision DVR?

On the old Hikvision CCTV recorder right click with the mouse, click menu, then click shutdown at the bottom right, and then click shutdown again. You'll see a message “system is shutting down please wait” after few seconds it will then show “Please power off”.

What is HDD error in Hikvision DVR?

Hikvision HDD error. Generally speaking, a Hard Drive is not detected error message indicates a hard disk drive (HDD) issue within your Hikvision DVR or NVR system. There are a few things you can do to solve this type of HDD error.

How to stop my recorder from beeping?

In order to get to the log, first, you’ll need to log into the recorder using your pattern or password. Right-clicking the screen and clicking the ‘main menu’ will usually prompt the login page. Once you are logged in, use your mouse to click the “OPERATION” tab, ...

Why is my tamper sensor so sensitive?

The tamper sensor can be a bit sensitive as it was designed to cover a wide array of miscellaneous scenarios. If it goes off it could mean a number of possibilities but it will often trigger due to a Coax cable connection losing signal, or if a camera’s fixed view is altered drastically and suddenly.

Why is my recorder beeping?

If your recorder is beeping after the hard drive has been initialised then this may be caused by things like only having 2 cameras connected to a 4 channel recorder or not having a network cable connected.

Why does my Hikvision recorder make a buzzer?

The most common reason people get this alarm sound is because they are setting up their recorder for the first time with a hard drive that has not been 'initialised'.

What does audible warning mean on a recorder?

Audible Warning will cause the recorder to beep if the selected event occurs

Can HDD error be re-enabled?

Individual alarms, such as ‘HDD Error’ can be re-enabled if desired.

Why is my recorder beeping?

If your recorder is beeping after the hard drive has been initialized then this may be caused by things such as not having a network cable connected or certain cameras being offline. Here are the steps how to turn off these alarms. The first step is to right click on your mouse and log-in into your recorder, and then select ‘Menu’. On the Menu click Configuration.#N#On the Configuration screen select ‘Exceptions’ on the left hand list of sections.#N#You need to click on the menu next to ‘Exception Type’ and select ‘All’.#N#Make sure the tick box next to ‘Audible Warning’ is unticked and then click the ‘Apply’ button.

Why does my Hikvision recorder beep?

in Hikvision. Hikvision recorders ( NVR or DVR) come with all the audible alarms enabled. This can cause the system to sound beep constantly even if everything is set up properly. The most common reason people get this beeping sound is because they are powering up their Hikvision DVR/NVR for the first time with a hard drive ...

How to disable audible warning on Hikvision?

You need to click on the menu next to ‘Exception Type’ and select ‘All’. Make sure the tick box next to ‘Audible Warning’ is unticked and then click the ‘Apply’ button. This has now disabled all the audible warning on your Hikvision recorder.

How to get exceptions on a recorder?

The first step is to right click on your mouse and log-in into your recorder, and then select ‘Menu’. On the Menu click Configuration. On the Configuration screen select ‘Exceptions’ on the left hand list of sections. You need to click on the menu next to ‘Exception Type’ and select ‘All’.

Can you use a surveillance hard drive on a DVR?

First of all, make sure you’re using a surveillance hard drive in your NVR/DVR. Once you have physically installed the hard drive on your recorder, you’ll be prompted to initialize the hard drive during the initial set up. Let’s assume that you are starting from the main live view menu.