How do I sync my Hayward ColorLogic pool lights? To re-synchronize your lights, turn the switch on, then back off, then wait between 11 and 14 seconds and turn the switch back on. When the lights come back on, they should enter program #1, and be synchronized. Refer to the included color card as a quick reference to the available programs.
How to reset ColorLogic lights?
How to resync UCL lights?
What is Hayward ColorLogic 2021?
How long does it take for lights to resync?
How long does it take for a ColorLogic controller to resync?
Why is my Hayward light not working?
Can you fix a Hayward pool light?
See 2 more
How do I resync my pool lights?
0:211:58Synchronising Spectravision LED Pool Lights | Andy's AnswersYouTubeStart of suggested clipEnd of suggested clipThe way to synchronize them mister make sure they've been switched off for around a couple ofMoreThe way to synchronize them mister make sure they've been switched off for around a couple of minutes. You then reapply the power to them for approximately 10 seconds. But no more than 15 seconds.
How do I sync my Hayward omnilogic lights?
0:021:02How to Sync ColorLogic Pool Lights in OmniLogic - YouTubeYouTubeStart of suggested clipEnd of suggested clipHey this is rich with true light pools uh today we're looking at how to sync your hayward colorMoreHey this is rich with true light pools uh today we're looking at how to sync your hayward color logic lights. Today we're looking at a uh hayward omni logic uh and then uh how can we sync. How can we
How do I get my pool light to change colors?
Flipping the switch initially turns your light on. Turning the switch off then on again will set the light to the second color. Repeating this procedure allows you to cycle through the various colors and light shows easily. Keep turning the switch off then on again until you have reached your desired setting.
How do I reset my LED lights in my pool?
0:020:58Pool light not working, resetting GFI - YouTubeYouTubeStart of suggested clipEnd of suggested clipLight is not on so both these gfis are tripped and they get wet or something happens so you justMoreLight is not on so both these gfis are tripped and they get wet or something happens so you just have to reset them you simply push this button.
How do I calibrate my Hayward OmniLogic?
The way it's used is to power down the OmniLogic, place the USB drive into the unit and then re-boot. The system will boot in calibration mode and allow calibration to take place. Once complete, power down the unit and remove the USB stick from the system and power back up as normal and you should be good to go.
How do I reset my Hayward OmniLogic?
The system is essentially a computer so a simple power cycle or 'restart' will fix the problem and it should auto reconnect to the wifi network.Turn off power at the breaker.Wait 5 minutes.Turn power back on and let the system reboot.
How do you change the color on a Hayward ColorLogic pool light?
0:241:36Hayward Colorlogic LED Pool Light Controller From Pool WarehouseYouTubeStart of suggested clipEnd of suggested clipOn simply push in on the knob. And now the lights and the pool will change to that color and you canMoreOn simply push in on the knob. And now the lights and the pool will change to that color and you can see that on the little screen right above.
Why won't my pool lights change color?
Motors. Some pool lights that change colors rely on small motors that rotate a multicolored lens so different portions of the lens filter the light being emitted by a single bulb. These lights are susceptible to motor failure, which will allows them to function normally but without any color change.
Can you replace the bulb in a Hayward ColorLogic pool light?
ColorLogic® 120V LED Replacement Bulbs are a quick, cost-effective way to upgrade standard incandescent pool lights to vibrant, color-rich, energy-efficient LEDs. Installation does not require rewiring or fixture replacements.
How do you reset your LED lights?
To begin with, make sure that your LED light is plugged into an outlet. Next, press and hold the button on top of the power cord for at least 10 seconds. After this time has elapsed, release the button and wait approximately one minute for it to turn off automatically before unplugging it from its outlet.
Why is my LED pool light not working?
Check the lighting fixtures You might be dealing with a worn-out seal, and you may need to have it replaced. If the lighting itself is the problem, you may need to buy new LED lights, especially if it's been damaged. If you're dealing with a blown bulb, you'll also need to get that replaced.
Why won't my pool lights come on?
Check the circuit breaker panel that's usually found on the side of your house. If the breaker that your pool light is on has been tripped, unplug whatever you just turned on or plugged in and then reset the breaker by turning it all the way off and then back on again. If that doesn't work, you may have a bad breaker.
How do you sync pool lights Hayward?
Once installed, all lights should be automatically synchronized, however, if they get out of sync, they can be re-synchronized easily. To re-synchronize your lights, turn the switch on, then back off, then wait between 11 and 14 seconds and turn the switch back on.
How do you sync audio lights?
How To Sync LED Lights To Music (Simple Method)Begin by plugging your LED into the multiplug adaptor to power it up.Turn the LED strip lights on for a few seconds and then off again.Plug your mobile device, laptop, or other audio playback devices into the same multiplug that the LED uses and start playing a song.
How do I update my Hayward OmniLogic?
You need to bring the USB memory stick to the OmniLogic and simply plug it into the side of the Local Display behind the Dead Front. Next, you will go into OmniLogic's Configuration Menu and push Firmware Upgrade. The OmniLogic will automatically reboot with the new Firmware.
How do I sync my DMX lights?
0:314:15How to Sync Lighting to Your Live Show - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing messages sent from our da W setting this all up is very simple just connect the DMX s by USBMoreUsing messages sent from our da W setting this all up is very simple just connect the DMX s by USB to your computer. Run a 3-pin XLR cable.
Hayward ColorLogic Lights Malfunctioning | Trouble Free Pool
Our pool is 3 years old, 100% Hayward equipment. Included are two ColorLogic LED lights. They are on the same circuit, so they should both be turning on/off together, and be on the same color cycle. Everything was as expected until about 4 months ago. Now We have intermittent problems with...
Two of Three Hayward Colorlogic Lights Not Turning On
Service came out and reported that both LED lights went bad. They will be replaced. The more concerning thing was general comments the person made about a lot of LED lights malfunctioning and that is wasn’t limited to Hayward and that Pentair lights were doing it (and I have Pentair bubblers).
How to change colors and operate your Hayward ColorLogic pool light ...
Hayward ColorLogic lights come standard as part of Planet Pools new pool package. With the benefit of having such a versatile and amazing color lighting system on your pool comes the complexities of operating it.
BACKYARD ENVY
Discover how Hayward's ColorLogic Pool, Spa, and Backyard LED Lights can transform your backyard into the perfect place for any occasion. Find a Hayward dealer near you today.
Find a Dealer Today
Discover how Hayward's ColorLogic Pool, Spa, and Backyard LED Lights can transform your backyard into the perfect place for any occasion. Find a Hayward dealer near you today.
What is a color logic light controller?
The ColorLogic Light Controller puts the power of colorful, customizable low-voltage ColorLogic LED lighting at your fingertips. Choose the perfect color option for your pool and backyard from right inside your home using the convenient dial and preview window. As the only wall controller that can be easily installed into an existing light switch, the ColorLogic Light Controller makes it simpler than ever to see your pool, spa and landscaping in a whole new light. Experience unparalleled color, control and convenience - choose the ColorLogic Light Controller for your backyard.
How many colors can you see with ColorLogic?
With the ColorLogic Light Controller’s sleek, simple design, you can instantly view and choose from 10 beautiful fixed colors and 7 color-changing light shows.
How to reset ColorLogic lights?
Press the [<] button till Reset ColorLogic to Default comes up, you can then reset ColorLogic lights to default by pressing the
How to resync UCL lights?
If the lights are controlled by an OmniLogic, you could try tapping in the right part of the dashboard, on the UCL light option. Then click on the body of water the lights are connected with. After that, you should try locating the resync icon which should be at the lower right corner. Immediately, this process is completed, the back arrow should be clicked in to return to the dashboard. Another convenient way is by entering and toggling relays while in service mode.
What is Hayward ColorLogic 2021?
posted on April 6, 2021. Pool owners are quite familiar with the Hayward ColorLogic pool lights. They brighten up the pool in the dark which is very essential in preventing pool accidents. These lights are actually pretty costly and buyers are generally dissatisfied when an issue arises with their lights. This can be a disappointment as they expect ...
How long does it take for lights to resync?
If the lights are controlled by a simple switch, you could try turning on the lights and wait for a period of 60 seconds.
How long does it take for a ColorLogic controller to resync?
You should then wait for a period of two minutes and press the resync button down for three seconds before releasing it.
Why is my Hayward light not working?
Apart from all this, one main issue associated with the Hayward lights is random light failure. This is usually caused by a voltage spike and it is advised that you call an electrician to examine your lines before installation.
Can you fix a Hayward pool light?
These are some problems faced while using the Hayward ColorLogic pool lights and you can be assured as they are nothing to worry about. You can easily fix them yourself but do not fix high voltage issues as they can be dangerous. Only consult a qualified expert for Hayward pool light replacement parts or for proper installation.
