How to Remove the Top of a Maytag Washing Machine
- Unplug the washing machine. This is a safety precaution any time you are opening the machine.
- Locate two screws approximately 4 inches off the floor near the two lower-front corners of the machine.
- Pull out on the bottom of the front panel of the machine and then pull down to unsnap the two plastic clips at the top of the front ...
- Lift the front edge of the top of the machine. It is hinged in back, and the front will simply lift up.
- Locate the two 3/8 inch machine bolts in the upper-right-hand corners of the front of the machine if the top of the washer will not simply hinge upward.
How to remove the top of a Maytag washing machine?
How to Remove the Top of a Maytag Washing Machine. Unplug the washing machine. Locate two screws approximately 4 inches off the floor near the two lower-front corners of the machine. Pull out on the bottom of the front panel of the machine and then pull down to unsnap the two plastic clips at the top of the front panel.
How to disassemble Maytag washer?
Rotating the dial
- Set the dial to its standard or normal position, facing up at 12 o’clock.
- Rotate the dial counterclockwise back to the standard position you started in.
- Turn the dial clockwise three settings so that it is in the 3 o’clock position.
- Turn the dial clockwise one setting.
- Turn the dial counterclockwise once to return it to the 3 o’clock position. ...
How to reset Maytag washer?
Maytag Commercial Washer Reset Code
- PF. If a power failure occurs when the dryer is running, you will see a power failure error code.
- F01. This is the ‘Primary Control Failure’ code. ...
- F02. If you entered diagnostic test mode, pressing the wrong button will cause this error to flash. ...
- F22
- F23
- F26
- F28. This code flashes when the moisture sensor strip is open in diagnostic test mode.
- F29. ...
How do you troubleshoot a Maytag washer?
- Assess the load.
- Determine whether the washer is plugged into the electrical outlet.
- Remove any kinks from the drain hose.
- Close the washer's lid securely to add pressure to the lid switch.
- Avoid overcrowding your load; an unbalanced, heavy load can contribute to excessive water fill that can leak.
How do you take the top off of a Maytag washer?
Pull out on the bottom of the front panel of the machine and then pull down to unsnap the two plastic clips at the top of the front panel. Once the two top clips have unhooked, remove the front panel entirely and set it aside.
How do you open a washing machine top panel?
0:002:48How To Open Your GE Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you're basically just pushing inside very gently and then once you push that in you'll be ableMoreAnd you're basically just pushing inside very gently and then once you push that in you'll be able to pull this forward you'll hear him push end.
How do you take the top off a washing machine?
0:594:07Whirlpool/Kenmore Top-Load Washer Model WTW4800XQ2 Disassembly ...YouTubeStart of suggested clipEnd of suggested clipPull the main top forward lift it up and support. It if you need to remove the inner tub first use aMorePull the main top forward lift it up and support. It if you need to remove the inner tub first use a flathead screwdriver to help release the tabs securing the tub ring. And pull the ring.
How do I open my top load Maytag washer?
How to Open a Maytag Top-Load WasherRemove all of the clothes from the washing machine, then disconnect the power to the appliance. ... Remove the two screws on the bottom of the front panel of the washing machine.Pull the bottom of the front panel out to release the two tabs at the top of the washing machine.
How do you take apart a top load washer to clean it?
0:392:50How to Clean, Remove and Replace the Agitator in your Washing MachineYouTubeStart of suggested clipEnd of suggested clipAnd then write down the center of the agitator as a little wound yard remove that just hold theMoreAnd then write down the center of the agitator as a little wound yard remove that just hold the agitator as you unscrew anticlockwise.
How do you take apart a Maytag front load washer?
3:3010:55Whirlpool Front-Load Washer Disassembly, Repair Help ...YouTubeStart of suggested clipEnd of suggested clipUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panelMoreUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panel housing mounting. Screws. You can now lift up the task to detach the housing.
How do I remove the top of my Whirlpool washer?
1:214:22How to Disassemble A Whirlpool Top Load Washer | PartSelect.comYouTubeStart of suggested clipEnd of suggested clipSimply detach the wire harness. We can then remove that switch simply by depressing a locking tab onMoreSimply detach the wire harness. We can then remove that switch simply by depressing a locking tab on some models there may be a retaining screw.
How do you remove the top of a Maytag dryer?
0:183:01Maytag Dryer Disassembly (Model #DE412) – Dryer Repair HelpYouTubeStart of suggested clipEnd of suggested clipNext remove the screws to release the front bulkhead from the cabinet. Reach under the drum and pushMoreNext remove the screws to release the front bulkhead from the cabinet. Reach under the drum and push the idler pulley up to release the belt tension unthread the belt from the pulley and motor shaft.
How to get to anything inside a Maytag washer?
Many parts of a Maytag washing machine are easy to work on, but in order to get to almost anything inside a Maytag washer you first need to remove the front cover and then lift up the top of the machine. Fortunately, Maytag makes this part of the job very simple. Advertisement.
What to do if you are opening a washing machine?
Unplug the washing machine. This is a safety precaution any time you are opening the machine.
How to snap clips out of a sewing machine?
If there are no screws on the front panel of your machine, then slip your flat screwdriver between the side and the front panel approximately 3 inches from the floor. Locate the clips by feel and push in slightly on them with your screwdriver until they snap out as you pull forward on the bottom edge of the front panel. ...
Where are the bolts on a washer?
Locate the two 3/8 inch machine bolts in the upper-right-hand corners of the front of the machine if the top of the washer will not simply hinge upward. Remove these two bolts with your ratchet and set them aside. Now lift up on the front edge of the top of the machine; it is hinged in the back and should lift up and back.
Can you force the front panel off of a Maytag?
Do not force the front panel off or force the lid to hinge up. If excessive force is necessary, then look for the cause. A few Maytag models have plastic snaps on the two bottom corners of the front panel instead of screws.
Step 1
Unplug the Maytag clothes dryer from the power source. Remove the two screws on the front panel. You will find them approximately 4 inches from the bottom, under the beveled edge.
Step 2
Pull the bottom of the front panel toward you until the clips on the top of the panel release.
Step 3
Carefully disengage the wires from the door switch and set the door aside.
Step 1
Unplug the Maytag clothes dryer from the power source. Remove the four screws. You will find one in the hinge on the upper right, one in the hinge on the lower right and one opposite each hinge.
Step 2
Lift the door slightly and pull back. The door and the hinges will disengage. Put the door aside.
Step 3
The front panel of the Maytag clothes dryer is shaped like a goal post. Grasp the skinny, upper sides and wiggle them back and forth to unclip the panel. Pull the skinny ends of the front panel toward you, lifting it off the bottom clips. Set the front panel aside.
