The Console and indicator diagnostic test on a Maytag Bravos Washing Machine is used to check the cycle selector knob, console indicators, user interface buttons, two-digit display, and beeper. 1. The washing machine should be in standby (off) mode. 2. Press and release the following buttons within 4 seconds.
Full Answer
What is the diagnostic test on a Maytag Bravos washing machine?
Console & Indicator Diagnostic Test Mode The Console and indicator diagnostic test on a Maytag Bravos Washing Machine is used to check the cycle selector knob, console indicators, user interface buttons, two-digit display, and beeper. 1. The washing machine should be in standby (off) mode.
Why won’t my Maytag Bravos wash Lint away?
Top-loading high-efficiency washers, like the Maytag Bravos, use much less water and that can result in lint not being washed away as easily as it is with a standard washer that uses a high-volume of water. It is helpful to run a cleaning cycle each month to flush away any lint residue in the washer. Use the Washer Correctly
How do I clean the filter on my Maytag Bravos washer?
To clean the pump filter, follow the directions in your washer manual to access the water pump. You may find lots of lint, coins, buttons, or even a sock that is causing a slow drain and leaving lint on your clothes. Problem With Maytag Bravos Fabric Softener Dispenser
How do I perform a diagnostic test on my Kenmore Bravos washer?
Perform steps 1 and 2 for the activation of the Bravos automatic diagnostic test mode then press the same button one more time while 88 is on the washing machine display for 5 seconds. Pressing the "STOP" or "POWER" button at any time to exit the washing machine's diagnostic mode.
See more
How do I put my Maytag Bravo in test mode?
Turn your cycle selector knob right (clockwise) one click to enter service/self-test mode. That's it..you have just instructed it to enter Diagnostic Test Modes.
How do I put my Maytag washer in test mode?
0:064:55How To Put Your Maytag commercial Washer In To Self Test Mode ...YouTubeStart of suggested clipEnd of suggested clipYou go left right right left right and if you're successful all of these lights will start flashingMoreYou go left right right left right and if you're successful all of these lights will start flashing and then you know you're in test mode to go into the quick test mode you want to toggle this switch.
How do you reset a Maytag Bravos washer?
Turn the Cycle Selector knob counterclockwise or left (all the way around) once. Next, turn the knob clockwise (right) – Go three clicks clockwise (count one… two… three as you turn the dial clockwise).
How do you put a washing machine in self test diagnostic mode?
6:0013:59How To Put Your Washer In Self Test Diagnostic Mode (Whirlpool Built)YouTubeStart of suggested clipEnd of suggested clipJust the spin light only to spin light is automatic test mode now what this is going to do is thisMoreJust the spin light only to spin light is automatic test mode now what this is going to do is this going to basically let water in it's going to agitate. It's going to drain.
How do I calibrate my Maytag Bravos washing machine?
1:192:03Whirlpool Maytag Top Load Washer Calibration Diagnostics - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou'll then need to hold the start button for a good 5 6 7 seconds or so until the lights stopMoreYou'll then need to hold the start button for a good 5 6 7 seconds or so until the lights stop flashing. And that pulls you out of diagnostic mode so that we can then go back in and calibrate.
How do you reset the sensor on a Maytag washer?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.
Is there a reset button on a Maytag Bravos XL washer?
Maytag Bravos XL washer calibration/ “Reset” (step by step) Turn the washer's Cycle Selector knob counter-clockwise or left once (all-the-way around). Now rotate the knob clockwise(right) – you should go 3 clicks clockwise(count 1… 2… 3 as you rotate the dial clockwise).
Why is my Maytag Bravos washer not spinning?
One of the most common reasons a washing machine won't spin is an unbalanced wash load. During a wash cycle, larger, heavier items can clump on one side of the machine, causing an imbalance that affects the spin cycle. Overloading the washtub with too many items can also cause an imbalance that prohibits spinning.
How do you run a diagnostics and read error code on a Maytag washer?
0:045:38How to Run Diagnostics and Read Error Codes on a Maytag WasherYouTubeStart of suggested clipEnd of suggested clipThen it's three ticks to the right one tick to the left and one tick to the right and you have to beMoreThen it's three ticks to the right one tick to the left and one tick to the right and you have to be pretty precise or your timing. Or it won't engage. And then when it engages the lights flash.
How do you run a diagnostic test on a Maytag dishwasher?
0:132:46DISHWASHER DIAGNOSTIC TEST—FAST AND EASY - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne two three and then you press the same keys again same sequence one two three. And then you pressMoreOne two three and then you press the same keys again same sequence one two three. And then you press it again one two three so you're doing three any three keys except the power key.
How do I reset my Maytag front load washer to factory settings?
Hold down the Delicates and Knits button for five seconds. The washer's LED display should now flash and start to blink, which means the error codes have been resolved and the washer has reset.
How do I reset my Maytag Direct Drive washing machine?
0:021:09How to Reset a Maytag Maxima Washer machine #Shorts - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay this is a maytag maxima washer if you're having a little trouble with the machine. So you cleanMoreOkay this is a maytag maxima washer if you're having a little trouble with the machine. So you clean up clean it up make sure it's clean and then you come up here you do one two three one two three
Automatic Diagnostic Test Mode
1. The washing machine needs to be plugged in and in stand by mode with all indicators off. 2. Choose any one button on the washer's console except...
Manual Diagnostic Test Mode
Perform steps 1 and 2 for the activation of the Bravos automatic diagnostic test mode then press the same button one more time while 88 is on the w...
Console & Indicator Diagnostic Test Mode
The Console and indicator diagnostic test on a Maytag Bravos Washing Machine is used to check the cycle selector knob, console indicators, user int...
How to Troubleshoot a Maytag Bravos Washer?
Is there a troubleshoot issue in your Maytag Bravo washer? If there is, you have to follow a few crucial steps to deal with it quickly.
Why do you need to clean Maytag washers after each month?
Therefore, after each month, you should have a cleaning cycle to flush away all the residue left in the lint.
How long does a Maytag machine last?
A Maytag machine will work perfectly for years if maintained correctly and checked weekly, trust me.
Why does my washer lint?
Another reason for excess lint on your clothes after the washer stops is that the water pump filter is not working well. Generally, it gets clogged.
Why does my washer vibrate after redistribution?
If it rocks or vibrates even after redistribution of loads, then there must be a problem with the feet. Adjust the feet accordingly on the washer.
How long do you have to cut off the power supply to a washer?
Firstly you have to cut off the power supply to your washer for at least 1 minute.
What does a timer do on a washing machine?
That’s because the timer controls all the features such as wash, rinse, and spin cycles.
How to test a Maytag washer lid switch?
How Do You Test the Lid Switch Inside a Maytag Washing Machine? Test the lid switch inside a Maytag washer using a continuity meter or multimeter. Opening and closing the lid should cause the switch to alternate between continuity and no continuity. To access the lid switch, open the back of the control panel.
What does it mean when a machine fills with water but does not agitate or spin?
When a machine fills with water but does not agitate or spin, the lid switch is suspect. The lid switch is a safety device that prevents the machine from operating when the lid is open. It activates each time the lid is opened, and closing the lid gently helps prevent the switch from malfunctioning.
What is a Maytag washer?
Share. Email. Courtesy of Maytag. Maytag is a familiar and popular name brand of washers and dryers. The Maytag line has been around for more than one hundred years with the first washer introduced to the market in 1907.
How to clean a washer with rubbing alcohol?
Begin by cleaning the switch contact points on the lid and the body of the washer with a cotton swab dipped in rubbing alcohol to remove any dirt and lint build-up.
How to clean a dishwasher with white vinegar?
Heat the vinegar in the microwave until it is very hot but not boiling. Dip an old toothbrush into the heated vinegar and give the dispenser a good scrubbing. It is also helpful after the scrubbing to fill the dispenser with the warm distilled white vinegar and let the empty washer run through a hot wash cycle.
Why is my laundry dispenser not working?
If dispensers will not work correctly is often a problem with the water flow into the unit. Detergent, bleach, and fabric softener are dispensed at the proper time in the laundry cycle by a burst of water that flushes out the dispenser cup. The water lines could be kinked or clogged with residue. It is also possible that the solenoid that controls water flow is not functioning correctly. To help you check the solenoid, water lines, and remove the unit for cleaning, consult the user/repair manual .
How to clean a sanitizer dispenser?
If the dispenser is removable, fill a sink with hot water and allow the dispenser to soak for at least 30 minutes. Use a small soft-bristled bottle brush to clean every opening. If the dispenser is not removable, you can still give it a good cleaning using distilled white vinegar.
Can you use too much detergent in a washer?
Using too much detergent leaves a residue on clothes that is sticky enough to hold onto lint and hair. No more than two teaspoons of high-efficiency detergent should be used per load of laundry.
Can Bravos washers continue after wash cycle?
Maytag Bravos washer will not continue to the next cycle after the wash cycle.
