As a rule of thumb, when tightening the chain, you should use a torque wrench. To tighten the chain, you should turn the wrench counterclockwise. The two markings on the wrench are “T”R”. Remember to always move the wrench to a side before checking the chainsaw chain.
How do you tighten the chain on a chainsaw?
If you want to properly tighten a chainsaw chain, remember the following steps. Loosen the bar nuts so you can easily adjust the chain tension screw. While pulling up on the tip of the bar, adjust the chain so it doesn't sag and it holds itself to the bottom of the bar.
How do I adjust the chain on my bike?
Loosen the bar nuts so you can easily adjust the chain tension screw. While pulling up on the tip of the bar, adjust the chain so it doesn't sag and it holds itself to the bottom of the bar. I like to pull on the chain for a reference. It should "give" about a 1/4 inch from the bar without much effort.
How do you adjust the guide bar on a chainsaw?
Most chainsaws come with "scwrench" (screwdriver/wrench) that matches their side plate nut and tension adjustment screw size. This will give the guide bar and chain the room they need to be adjusted.
How do you know when it's time to tighten a chain?
If the chain's drive links are disengaged from the guide bar when pulled, then it's time to tighten it up. Chainsaw chains can also be overtightened.
Why does my Echo chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won't change as you work your saw.
How do I tighten the chain on my ECHO CS 352?
0:001:53How to adjust chain tension on Echo chainsaw (CS 352) - YouTubeYouTubeStart of suggested clipEnd of suggested clipUntil the chain just snugs up a little bit against it you don't want it tight you just want it toMoreUntil the chain just snugs up a little bit against it you don't want it tight you just want it to get up there and then you check it by just pull it and see if it goes smoothly that's a little jerky.
What do I do if my chainsaw chain is loose?
0:312:05How to Tension a Chainsaw Chain - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'll go ahead and adjust that now I just want to tighten that up a little bit it'll pull theMoreAnd I'll go ahead and adjust that now I just want to tighten that up a little bit it'll pull the chain up tight against the bar. Like that and proper tape fit is achieved.
Where is the tension screw on a chainsaw?
0:281:33Chapter 5: Adjusting Your Chainsaw's Chain Tension - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou should now have a slight up-and-down movement of the bar. Holding the tip of the bar up rotate.MoreYou should now have a slight up-and-down movement of the bar. Holding the tip of the bar up rotate. The adjustment screw clockwise until the chain is seated against the bottom rail of the bar.
How do I tighten the chain on my ECHO CS 490?
0:382:01ECHO Pro-Tip: How to Adjust Chain Tension on a Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold the bar nose up and while using a slotted screwdriver or scrunch turn the adjuster screwMoreHold the bar nose up and while using a slotted screwdriver or scrunch turn the adjuster screw clockwise until the chain contacts the underneath side of the bar.
How tight should your chainsaw chain be?
The chainsaw chain should feel snug but still pull freely. Finally, perform a "snap" test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Why does chain jump off chainsaw?
Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain. Even if your chain saw is not throwing its chain, the tension might not be correct.
Is the chain on a chainsaw supposed to be loose?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can't pull the drive links out of the bar nose.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don't over-tighten the chain as this could cause it to break.
How do I tighten the chain on my Echo Power Pruner?
0:382:18How to Adjust Chain Tension on Echo Pole Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you want to tighten this just grab a screwdriver. You want to tighten it so this gets sucked upMoreAnd you want to tighten this just grab a screwdriver. You want to tighten it so this gets sucked up most of the way but that it still moves smoothly like this that's moving smoothly.
What angle do you sharpen an Echo chainsaw?
2:146:06How to sharpen an ECHO chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipBegin by sharpening the shortest or most badly damaged cutter. The cutting angle varies between 25.MoreBegin by sharpening the shortest or most badly damaged cutter. The cutting angle varies between 25. And 30 degrees depending on the type of chain.
What size chainsaw file do I need?
Simply put, the type of chainsaw file you need directly corresponds with the size of your chain pitch. The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be.
How to tension a chainsaw?
Steps to Tension a Chainsaw Chain. Even though tensioning a chainsaw chain is easy and takes less than a minute, it's important to do each step carefully and correctly. Forgetting to do something like lift the guide bar nose when tightening it can seriously affect your tool. Most chainsaws come with "scwrench" (screwdriver/wrench) ...
What happens if a chainsaw chain is too loose?
If a chainsaw chain is allowed to become too loose, it can easily come off the bar during operation and create an unsafe situation for the user. Chainsaw chain tension should be checked and tightened often. We explain simple steps for how to tension a chainsaw chain below.
Can chainsaw chains be overtightened?
Chainsaw chains can also be overtightened. There should be at least a little play in the chain, just not enough for the drive links to leave the guide bar. Tightening a chainsaw chain too tightly risks breaking it during operation.
Can chainsaw chains be loose?
Chainsaw chains stretch and become loose during operation. This article's maintenance steps explain how to properly tension a chainsaw chain in under a minute. Chainsaw chains stretch during normal operation and begin to sag on a saw's guide bar. If a chainsaw chain is allowed to become too loose, it can easily come off ...
Where are the brakes on a chainsaw?
This will give the guide bar and chain the room they need to be adjusted.#N#The brakes of some chainsaws are attached directly to the side panel. If this is the case, make sure to unlock the brake before removing the side panel.
Can you pull a chainsaw chain out of the bar?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can't pull the drive links out of the bar nose.
How to tighten chainsaw chain?
If you want to properly tighten a chainsaw chain, remember the following steps. Loosen the bar nuts so you can easily adjust the chain tension screw. While pulling up on the tip of the bar, adjust the chain so it doesn't sag and it holds itself to the bottom of the bar. I like to pull on the chain for a reference.
How to check chain tension?
Once you have the perfect tension and still holding up on the bar, tighten the bar cover nuts which locks the bar into place. To check the proper chain tension, after you've tightened the bar cover nuts just pull up on the chain and see how much it gives .
How to adjust chain tension on chainsaw?
To adjust the chainsaw chain tension, loosen the bar nuts first. Loosening the bar nuts will accomplish two things. First, it allows the bar to move forward as you adjust the tensioning screw which tightens the chain. Second, it allows the bar to move up and down .
Why is chainsaw chain tension important?
Proper chainsaw chain tension is almost as important as the sharpness of your chain. A chain that's too tight won't bite into the wood and it will prematurely wear out your drive sprocket because it puts too much tension on the sprocket itself. When you think about a chainsaw chain, it's basically an oval. As the engine moves the chain ...
How to tell if chainsaw chain is too loose?
To start with, look at your chain. If you can see the chain sagging down from the bottom of the bar .....it's too loose. On the other hand, if you tug on the chain and it doesn't easy separate itself from the bar.......it's too tight. This photo shows a chainsaw chain that is too loose.
Why does my chain have slack when cutting?
By adjusting your chain in the "up" position, it eliminates the slack in the chain when you cut because the bar is already in the up position. It almost takes three hands but it's possible with just two. To start, loosen the bar cover nuts.
What happens if your chain is too tight?
So, if your chain is too tight it won't take long for physics to damage your saw. A chain that's too loose is also a dangerous scenario. A loose chain can derail itself from the bar and whip back towards you, possibly cutting your hands or legs. The proper chain tension is similar to a Goldilocks nursery ryme.
