Turn on the pump and the dirty water will flow out the waste line. Once the water runs clear in the valves sight glass, turn off the pump. Rotate the valve to rinse. Turn on the pump for 20-30 seconds.
- Ensure the hoses are securely attached. ...
- Check the skimmer water level. ...
- Add water to the pump basket. ...
- Open the air valve. ...
- Confirm that the necessary cleaning agent is in the filter. ...
- Monitor the filter's pressure gauge and water return flow.
How do I hook up my Hayward pool pump?
The process of how to drain the pool with Hayward pump
- First, you need to set It up. You Will require at least a 100-foot outlet hose a hose connector, and a hose clamp.
- Connect the hose pipe to sewer and pump. First of all, find your sewer drainage pipe and connect it to the pump using a hosepipe. ...
- Drop the pump in the shallow end. ...
- Start draining the water. ...
How do you program a Hayward variable speed pool pump?
You can program it (not sure if you are using the standalone interface on the back of the pump or through a controller) to kick to higher speeds on a timed basis for cleaners or solar. The 4 speed buttons can be used for heater operation or spa jets if you have a spa. John the Hayward Tech. [email protected].
How do you replace a Hayward pool pump?
- Using a flathead screwdriver, begin to pry one side of the lock ring assembly 'out-and-up' towards the top of the body.
- It may take at least 2 or 3 screwdrivers to begin lifting the lock ring assembly over the lip it rides under.
- After clearing the lip at the starting point, begin working your way around the lock ring assembly until you free it.
How to operate a Hayward pool pump?
How to Operate a Hayward Pool Pump. Ensure the hoses are securely attached. The Hayward pool pump works well because it creates a vacuum environment. Check the skimmer water level. Add water to the pump basket. Open the air valve. Confirm that the necessary cleaning agent is in the filter. Monitor the filter's pressure gauge and water return flow.
How do I start my Hayward pool filter?
1:102:12Opening Your Pool- How to Prime Your Filter Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere might have been an error in the hose you got to redo that step. But as long as you see waterMoreThere might have been an error in the hose you got to redo that step. But as long as you see water movement in there and you got water on top of that basket.
How do I turn on my pool pump?
0:581:52How to use your pool pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipTurn the valve until the arrow is pointing towards the skimmer in this position the check valveMoreTurn the valve until the arrow is pointing towards the skimmer in this position the check valve closes. The skimmer Inlet. And 100% of the pumps power is concentrated on the bottom drain.
How do you manually turn a Hayward pump?
0:111:35Hayward XE Series Pool Pumps - Manual Override - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere is a manual override function available to enter manual override at any time during normalMoreThere is a manual override function available to enter manual override at any time during normal operation. Simply press and then release the button.
Why is my pool pump not coming on?
It could be something blocking it, a dirty pool filter, or too much air in the system. If there's something blocking your pump's suction, check your filter gauge. If it's 10psi above the normal reading, clean your filter. This will reduce pressure and reset your pump's flow.
Why is my Hayward pool pump not turning on?
Check all connections, circuit breakers, and fuses. Repair or replace any tripped breakers or blown fuses. Inspect the motor shaft for any obstructions. Remove the pump and basket, then look for and remove any debris in the shaft.
How do I turn on my pool filter?
0:071:48There Are Several Positions On My Pool Filter. How Do I Work It?YouTubeStart of suggested clipEnd of suggested clipHow do I work it first always remember to turn your pump off when changing positions on your filterMoreHow do I work it first always remember to turn your pump off when changing positions on your filter valve the filter. Position is used to filter the pool.
How do I turn on my above ground pool pump?
4:318:17Start Up Instructions for your New Above Ground Pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're done you only want to run that for let's say about 15 seconds or so. Now we push it down weMoreWe're done you only want to run that for let's say about 15 seconds or so. Now we push it down we put it back to filter. And we're ready to go now. We're going to plug our pump.
How do I know if my pool pump is working?
0:434:58POOL PUMP Not Working? How To Fix 6 Common Pump ProblemsYouTubeStart of suggested clipEnd of suggested clipIf the motor shaft isn't rotating check to see if the motor is jammed with debris. And finally ifMoreIf the motor shaft isn't rotating check to see if the motor is jammed with debris. And finally if the pump turns on but isn't running at full steam. And you hear a humming noise check your capacitor.
How do I turn my Hayward pool pump on after winter?
0:102:01How to PRIME a Swimming POOL PUMP | Swim University - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo that way the water goes inside the filter head and right back out to the pool make sure all theMoreSo that way the water goes inside the filter head and right back out to the pool make sure all the plugs. And everything are removed from your pool. Before you turn anything on now if your pump.
How does a Hayward pool pump work?
Water is drawn from your pool by the powerful suction created from the pump.The pump draws the water through the skimmers and drains, removing large debris during the journey.When the pump's impeller is reached, pressure forces water through the filer, catching any debris not caught by skimmer baskets.More items...
How do you troubleshoot a Hayward pool pump?
How to Troubleshoot a Hayward Pool PumpStep 1: Check the Hoses. Tighten all hose connections on the pump and filter. ... Step 2: Inspect the Pressure Gauge. ... Step 3: Check the Skimmer Basket. ... Step 4: Remove Debris. ... Step 5: Inspect the Impeller. ... Step 6: Backwash the Filter. ... Step 7: Replace the Sand or DE.
How do you manually turn on a pool pump impeller?
0:532:37Swimming Pool Service Tip: Unclogging Your Impeller - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can put a screwdriver or NPS pool supply cells a what's an impeller unclog er it's a tool justMoreYou can put a screwdriver or NPS pool supply cells a what's an impeller unclog er it's a tool just to unclog the impeller.
Step 2
SET CURRENT DAY AND TIME - Press the Menu button. You will see a screen that says "Configuration Menu Locked".
Step 3
UNLOCK CONFIGURATION MENU - Press and hold down the < and > buttons until the screen changes to "Configuration Menu Press > to Enter".
Step 4
LOCATE TIME SCREEN - Press > twice and you should see the main time screen.
Step 6
CHANGE DAY - The day will be blinking. Press the + or - to change the day. Once the correct day appears, press > to move over to the time.
Step 7
CHANGE TIME - Once the hour is blinking, press + or - to change it. Press > to move over to the minutes and then AM/PM. Once the minutes and AM/PM is set, press > to take you to the next category (RPMS).
Step 8
SPEED SELECTION - After completely setting the time and hitting >, you'll move on to the RPM or % Selection. You can press + or - to switch between RPM's or %.
Step 9
MAX SPEED - The max allowed speed can be changed by pressing + or -. Once you have selected the max speed, press > to move on to minimum speed. Note: You may want to test the speeds by running the pump before programming the max and minimum speeds. Salt systems and heaters have minimum and max flow rates.
Hayward Pool Pump Troubleshooting
1 Check the filter. Is it dirty? Clean it. 2 Check the motor. Is it working properly? Replace if necessary. 3 Check the impeller. Is it clean? Clean it. 4 Check the belt. Is it worn? Replace if necessary. ## FAQs
Deep check the hoses
Check the hoses for leaks. If any leak is found, stop using the pump immediately. How to fix a leaking hose?
Check the Pressure Gauge
If the gauge explains zero pressure, the problem is not the pump itself but rather the hose connection. Check the connections between the pump and the tank and between the tank and the outlet. If the gauge still explains zero pressure after checking these connections, the problem is likely the hose itself.
Investigate the Skimmer Basket
Check if the skimmer basket is full of oil. If it is empty, fill it with oil. If the skimmer basket is filled with oil, check the level of the oil in the reservoir. It should be about half way. If the level of the oil is low, remove the drain plug and pour in more oil until the level reaches halfway.
Check the Impeller
Check the impeller blade is clean. Cleaning the blades helps to prevent clogs. Check the Drain Plug Answer: Remove the drain plug from the bottom of the tank.
Backwash the Filter
Remove the filter basket and backwash the filter using hot water. Clean the Tank Answer: Rinse the tank with warm water.
How do I know if my Hayward pool pump is bad?
If the motor sounds like it’s running but the pump isn’t moving any water, check the following: 1 Make sure the electrical cord is plugged into a good outlet. 2 Check the breaker box if applicable. 3 Check the circuit breakers in the panel. 4 Check the fuse box if applicable. 5 Check the wiring harness.
How to start up a pool before flipping the switch?
Before you flip the switch, you'll want to remove the ice compensators from the skimmer put your skimmer baskets back and screw in the return jet eyeball fittings that direct water into your pool. At this point, you should also check your water level.
What to do after pool is turned on?
After your pool is turned on and circulation begins, you should walk around and inspect all of the various parts for leaks and other possible issues.
What to do after reattaching pool equipment?
Make sure all of your equipment is ready to get back to work. After reattaching your pool equipment, you should reinstall your deck equipment. Everything from the ladder to the diving board.
How do I clean a pool cover?
Step 2. Remove the cover from your pool 1 Try and remove as much loose debris from your cover as possible to prevent it from making its way into your pool. 2 Start to slowly peel back your cover, folding it in halves as you do, for easy removal. 3 Once the pool cover is off, lay it out and sweep it off before cleaning it thoroughly with soap and water. It should be clean and dry before you place it into storage for the season.
How to get rid of algae in pool?
Once properly balanced, you'll want to shock your pool with a quality shock treatment to get rid of all that winter algae buildup.
What to do before you remove the cover from an inground pool?
Before you remove the cover from your inground pool, you'll want to make sure that you have the necessary supplies to treat the water. The last thing you want to do is get halfway through the process only to realize that you don't have what you need.
When should I put my pool filter and pump away?
While some people leave pool items in the same place all year round, others prefer to put them away during the wintertime to avoid exposing it to the elements. Regardless of your approach, always make sure your pool pump and pool filter (including their various parts) are secured in place.
How long does a Hayward pump run?
Pump only Runs for 5 seconds. If your Hayward pump runs for only 5 seconds and shuts off, check the incoming voltage. Most inground Hayward pumps are shipped to accept 230V, and if you only give it 115V, it can’t get up to speed.
What causes a pool pump to leak?
On the plumbing side, you can have problems with air leaks, water leaks or just getting the water to flow properly.
Why does my pump have a breaker?
If the breaker trips while the pump is running, the pump is likely drawing more amperage or voltage than the breaker rating . This could be caused by incorrect voltage or from clogged or restricted pipes, valves or impeller. It could also be just a bad breaker.
What happens when a pump trip a breaker?
When the breaker trips when trying to turn on the pump, most likely the motor shaft is frozen, the impeller is stuck, or the capacitor has blown. In some cases, it can be a bad breaker, especially one that is used often to turn the pump on and off.
What to do if pump won't start?
If the pump won’t start or run, check these things. If the motor does not turn on, check the breaker and timeclock switches. If the motor hums but does not start, check that the shaft is free-spinning, then check the capacitor. If the motor makes no noise at all, check the wiring and terminal connections.
Why does my pump motor make a humming noise?
Makes Noise: If the pump motor makes a humming sound when trying to start, you likely have a bad start capacitor.
Why does my pump shut off?
Other causes of a pump shutting itself off include loose or broken wires or incorrect voltage, more than 10% more or less of the rated input voltage. In most cases however, a motor that is over-heating tends to be defective beyond repair, when caused by an internal short across the motor windings.
Where is the pool pump located?
A pool pump is placed in the center of the pool that gives proper flow to the water and always keeps clean and safe. Sometimes there are distinct problems happen its leaks water and gives a loud sound. In this condition, you need to get it ASAP. If the problem does not solve your own self then call the professionals.
Why is my air pump not working?
Provide shade that air is passing freely on all parts of the pump. Sometimes wires are broken or the wrong voltage is the reason for not working. Wires are correctly placed on your own but if the motor is overheating, you can call professionals and change it immediately.
Why does my pump smoke?
Smoking and sparkling problem occur because of electricity problems. Mostly the pump motor receives 115V. When the motor received high voltage pressure like 230V its might be smoking or sparkling. Sometimes it happens when the shaft seal can are not correctly installed in this way pump produces smoke.
Step 1
First and foremost, make sure that power to the pump has been cut off. Unplug the pump if possible.
Step 2
Disconnect the hoses by removing the hose clamp then sliding the hose off of the hose adapter. Place the hoses over the swimming pool wall so that the water does not drain out of the pool.
Step 3
I recommend placing the pump on a shop bench or table so that it is easier to work on.
Step 4
Remove the pump lid by gripping the handle and slowly turning the cover counter clockwise, the pulling up towards you. Once the cover is off, remove the basket and drain any water inside of the strainer housing.
Step 5
Next, we’ll need to remove the strainer. To do this, we’ll first need to remove the c-clip that locks it into place. Simply pull it gently outwards towards you and lift it out of place.
Step 6
Now you can begin turning the strainer counter clockwise (if you are facing the strainer) until it can be removed.
Step 7
Depending on which motor you have on your PowerFlo, this next step will vary. If the motor doesn’t have a cover on the end of it, the four thru-bolts should be visible. Using a ¼ socket, loosen and remove the thru-bolts. If you feel resistance, I would recommend stopping and contacting a professional.
